• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.494-496
• /
• 2000

The properties of piezoelectric and dielectric for 0.05Pb$(Mn_{0.4}W_{0.2}Nb_{0.4})O_3$ - $0.95PbZr_{x}Ti_{1-x}O_{3}$ compositions have been investigated. In the composition of 0.05Pb$(Mn_{0.4}W_{0.2}Nb_{0.4})O_3$-$0.95PbZr_{0.51}Ti_{0.49}O_{3}$, the values of $k_p$ and ${\varepsilon_{33}}^T/{\varepsilon}_0$ are maximized, but $Q_m$ was minimized ($k_p$=56.5[%], $Q_m$=1130, $d_{33}$=258[pC/N], ${\varepsilon_{33}}^T/{\varepsilon}_0$=1170). The grain size was suppressed and the uniformity of gram was improved at the $1100[^{\circ}C]$. Dielectric constant increase at the Ti rich, but decrease at the Zr rich after poling. Because the dielectric constant after poling is determined by compromising effects between dipole switching and electostriction inducing stress(dielectric constant increasing factor) and dipole rotation to the poling direction (dielectric constant decreasing factor).

• Journal of the Korean Society for Nondestructive Testing
• /
• v.18 no.3
• /
• pp.163-171
• /
• 1998

Near/far field length and directivity of transducers were investigated for the improvement and evaluation of the detectability of flaws in a disc. The reference block is fabricated for the disc of stage 6 in Yonggwang unit 1. The near/far field and directivity of an ultrasonic transducer with the center frequency of 5MHz were calculated for the inspection of the disc. These values showed good agreements with the experimental results. In the system composed of a wedge and a disc, those are evaluated theoretically and experimentally for the specimen with the artificial flaws of the size 2mm and 4mm and an ultrasonic transducer with the center frequency 5MHz and diameter 0.5inch. The detectability of keyway-flaw and detectable region for inspection were evaluated by using both tangential $45^{\circ}$ and $90^{\circ}$ transducers located at the distance of 53mm and 75mm from the disc hub, respectively.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.846-850
• /
• 2002

A PMN-PT-BT/Ag composite was prepared by surface modification with MgO sol with hoping to suppress silver's migration during sintering. The mixture of PbO, $N_2O_5,\;TiO_2\;with\;Mg(NO_3)_2$ instead of MgO was ball milled, the solvent was removed and then the dried powders were calcined at 950$^{\circ}C$/1h. The calcined powder were treated with 3.0 mol% $Ag_2O$ and 1.0 wt% MgO sol and calcined at 550$^{\circ}C$/1h. The dielectrics sintered at 1000$^{\circ}C$/4h under a flowing oxygen showed the density of 7.84g/$cm^3$, the room temperature dielectric constant of 18400, the dielectric loss of 2.4%, the specific resistivity of $0.24{\times}10^{12}{\Omega}{\cdot}cm$. It also showed the bending strength of $120.7{\pm}11.26$ MPa and the fracture toughness of $0.87{\pm}0.002\;MPam^{1/2}$ which were comparable to commercial PZT. The microstructure sonsisted of grains of ∼4${\mu}m$. SEM and SIMS analysis showed that Ag grew as ∼1${\mu}m$ and excess MgO as ∼0.5${\mu}m$.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.981-983
• /
• 1999

In this paper, the electrical characteristics of $\lambda$ vibration-mode piezoelectric transformer for applying to CCFL driving inverter was investigated. Piezoelectric transformer was made of PZT - PMN - 0.5wt% $Nb_{2}O_{5}$ composition. As a results of the electrical characteristics of piezoelectric transformer, when applied voltage was $35[V_{rms}]$ in $100[k{\Omega}]$ load resistance, output voltage was about $710[V_{rms}]$ and output power was more than 2[W]. As output power increased, step-up ratio and temperature was very stable until output power was 2.5[W]. Also, Efficiency was maximum in $70[k{\Omega}]$ load resistance, and about 89[%]. Also, when CCFL was used as load, the maintaining voltage was $700[V_{rms}]$ and the luminescence was $2000[cd/m^2]$ in applying $25[V_{rms}]$ to piezoelectric transformer. Conclusively, piezoelectric transformer fabricated in this paper can be applied to piezoelectric inverter for CCFL driving.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.279-282
• /
• 2003

In this paper, to apply piezoelectric transformer for PDA backlight inverter, piezoelectric transformer using the composition which $Nb_2O_5$ added into PNW-PMN-PZT ceramics was fabricated as Rosen-type one with the size of $1165mm^3$. And their electrical characteristics were investigated with the variations of load resistance and driving frequency And then, the driving circuit for PDA CCFL(0.6W) which composed of the two MOSFETs connecting in series was manufactured using piezoelectric transformer, VCO and one-chip microprocessor. After driving for 25 min using the proposed circuit for PDA CCFL(0.6W), driving frequency of 214.4kHz, input voltage of 31.78 V and input current of 21.1mA were shown. And then, output voltage of 293.2 V and output current of 2.2mA were shown. At the same time, efficiency of 96.2$\%$ and temperature rise of $3.6^{\circ}C$ were appeared at the piezoelectric transformer.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.3 s.246
• /
• pp.318-327
• /
• 2006

Due to the diversified use of recent Piezoelectric Zirconate Titanate Composite Actuate. (PZTCA), various PZTCAs with the different ply orientation of the fiber layer have been applied. For this reason, the applicable bending moment equation is necessary even though the fiber layer ply orientation and the laminate configuration are changed. The aim of this research is to evaluate the relationship between the total effective moment $(M^E)$ and Bernoulli-Euler bending moment (M) when the ply orientations of UD CFRP are changed. In conclusions, firstly, as the performance test results by the CFRP ply orientation, the performance of [0] and [90] were stable. However, while the performance of [+45] was suddenly decreased after 5 hours. Secondly, the change of $(M^E)$ by the CFRP ply orientation was evaluated. As the CFRP ply orientation was increased from [0] to [+60], the $(M^E)$ were gradually decreased. However, they became a little bit increased from [+60] to [90]. Finally, after the change of M by the CFRP ply orientation was evaluated, it was found that $M^E=2.2M$ was valid for just [0] and that there was a relationship between $M^E$ and M according to the ply orientation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.478-480
• /
• 2001

Fe-base amorphous films exhibit large saturation magnetostriction and soft magnetic Properties, which make them suitable for strain sensor applications. Most important material properties for the performance of these elements are the superior soft magnetic properties, such as high permeability and small coercive force, as well as magnetoelastic properties. It is well known that the strain generated in film deposition and/or post-heat treatment processes is one of important material properties, which effects on the soft magnetic properties of the film via magnetoelastic coupling. In this study, the effect of an isotropic strain in plane of magnetic films have been performed experimently. Amorphous films with the composition of (F $e_{90}$ $Co_{10}$)$_{78}$S $i_{l2}$ $B_{10}$ were employed in this study. The film with 5${\mu}{\textrm}{m}$ thick was deposed onto the polyimide substrate with 50${\mu}{\textrm}{m}$ thick by virtue of RF sputtering. The film was subject to post annealing with a static magnetic field with 500Oe magnetic field intensity at 35$0^{\circ}C$ for 1 hour. The polyimide substrate with the film was bonded with an adhesive on PZT piezoelectric substrate with 600${\mu}{\textrm}{m}$ thick in applying voltage of 500V. The change in MH loops of films due to the isotropic strain was measured by using VSM. The coercive force was evaluated from MH loops. It has shown in the results that M-H loops of films are subject to change considerably with a dc voltage, resulting of the magnetization rotation from normal to plane direction as the applied voltage is changed from 500V to 250V.50V.V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.312-312
• /
• 2010

모터나 기계류와 같이 주변에서 발생하는 미활용 진동에너지를 전기에너지로 수확하기 위한 Piezoelectric Energy Harvester를 개발하고자 하였다. PZT-5H의 조성으로 후막세라믹 적층 구조 캔틸레버 타입의 압전시트를 통해 압전 에너지 하베스터를 제작하였다. 일반적으로 진동에너지를 수확하여 전기에너지로 변환시키는 압전 에너지 하베스팅 기술은 에너지 효율이 낮은 문제점을 가지고 있으므로 에너지 효율을 높이기 위한 방법으로 본 연구에서는 Unimorph 와 Bimorph 타입의 캔틸레버의 가로, 세로, 두께, 재료변수에 따라 발생하는 최적의 효율을 가지는 구조를 찾고자 하였다. 캔틸레버 각 변수에 따른 공진주파수 대역에서 발생하는 전압을 분석하여 50Hz의 공진주파수를 가지는 60*35*0.2mm의 캔틸레버를 설계하였다. 시뮬레이션을 통해 얻어진 결과를 실험적으로 검증하기 위해 전력량을 측정한 결과, Bimorph는 Unimorph 타입에 비해 2배가량의 향상된 발전특성을 가지며 에너지 하베스터에서 초당 $76.2\;{\mu}W$의 전력량을 가지는 것을 확인하였고 시뮬레이션 결과와의 타당성을 확인하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.7
• /
• pp.563-567
• /
• 2011

The most widely used piezoelectric ceramics are lead oxide based ferroelectrics (PZT). However, the toxicity of lead oxide and its high vapor pressure during processing have led to a demand for alternative lead-free piezoelectric materials. We synthesized Lead-free piezoelectric ceramics of $0.96(K_{0.5}Na_{0.5})NbO_3-0.04SrZrO_3+x$ mol% $ZrO_2$ [KNN-SZ+$xZrO_2$; x= 0~0.10] doped with 0.1 wt% $MnO_2$ by a conventional solid state method. We investigated the piezoelectric properties and microstructures of these disk samples sintered in reduced atmosphere in order to evaluate the possibility of the multilayered piezoelectric ceramics having the base metal such as Ni as a internal electrode. All of these KNN-SZ samples sintered in 3%$H_2-97%N_2$ atmosphere at $1,140^{\circ}C$ exhibit pure perovskite structure irrespective of the content of $ZrO_2$. Meanwhile, the sintering denisty and piezoelectric properties such as $K_p$, $Q_m$ and $d_{33}$ of KNN-SZ samples as a function of $ZrO_2$ content show the maxima ($k_p$=28.07%, $Q_m$= 101.34, $d_{33}$= 156 pC/N) at x= 0.04 and it is likely that there is some morphotropic phase boundary(MPB) in this KNN-SZ+$xZrO_2$ composition system. These results indicate that the ceramic composition is a promising candidate material for applications in lead free multilayer piezoelectric ceramics.

• Korean Journal of Materials Research
• /
• v.30 no.7
• /
• pp.343-349
• /
• 2020

NKN [(Na,K)NbO₃] is a candidate lead-free piezoelectric material to replace PZT [Pb(Zr,Ti)O₃]. A single crystal has excellent piezoelectric-properties and its properties are dependent of the crystal orientation direction. However, it is hard to fabricate a single crystal with stoichiometrically stable composition due to volatilization of sodium during the growth process. To solve this problem, a solid solution composition is designed (Na,K)NbO₃-Ba(Cu,Nb)O₃ and solid state grain growth is studied for a sizable single crystal. Ceramic powders of (Na,K)NbO₃-M(Cu,Nb)O₃ (M = Ca, Sr, Ba) are synthesized and grain growth behavior is investigated for different temperatures and times. Average normal grain sizes of individual specimens, which are heat-treated at 1,125 ℃ for 10 h, are 6.9, 2.8, and 1.6 ㎛ for M = Ca, Sr, and Ba, respectively. Depending on M, the distortion of NKN structure can be altered. XRD results show that (NKN-CaCuN: shrunken orthorhombic; NKN-SrCuN: orthorhombic; NKN-BaCuN: cubic). For the sample heat-treated at 1,125 ℃ for 10 h, the maximum grain sizes of individual specimens are measured as 40, 5, and 4,000 ㎛ for M = Ca, Sr, and Ba, respectively. This abnormal grain size is related to the partial melting temperature (NKN-CaCuN: 960 ℃; NKN-SrCuN: 971 ℃; NKN-BaCuN: 945 ℃).