• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.4
• /
• pp.367-375
• /
• 2013

The mechanical vibration of a PM synchronous motor at low speeds due to the back emf harmonics may be serious problems in some application such as MDPS(Motor driven power steering), electric vehicles. In this paper, torque ripple reduction for an interior PM synchronous motor including back emf harmonics is proposed. The dq flux linkage harmonics of the permanent magnet are estimated on real time by using the dq currents of the real system and the model of the MRAS observer. Based on the estimated flux linkage harmonics, the dq harmonic currents for reducing the torque ripples are compensated on the dq reference currents. The estimation of the flux linkage harmonics by the MRAS observer and the torque ripple reduction of the proposed algorithm was verified by the simulation and experiment.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.7
• /
• pp.323-328
• /
• 2005

This paper is proposed maximum thrust design of slotted permanent magnet linear synchronous motor(PMLSM) using surface harmonic method(SHM) considering slot effect. The genetic a1gorithm is used for optimization. The functional are selected the maximum thrust and the minimum detent force. This time. design parameters are set as permanent magnet(PM) width. PM height and slot width. Thrust is increased from 272[N] to 295[N] and detent force is decreased from 5[N] to 2.43[N] greatly in optimum design. Therefore, thrust ripple isn't generating almost. Also, the results of 2D EMC considering slot-effect are compared with ones of experimental and finite element analysis..

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.12
• /
• pp.2116-2121
• /
• 2007

Numerical identification of synthetic d-q flux linkage, representative parameters for analyzing interior buried PM synchronous Motor(IPMSM) with distinguished magnetic saturation, has been peformed. Particularly, numerical identification of synthetic flux linkage using modified Finite Element Method(F.E.M) has been taken cross-magnetization of multi-layered PM configuration into consideration. Futhermore, experimental identification on the purpose-built prototype has been made to verify the validity of the numerically identified synthetic d-q flux linkages.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.2
• /
• pp.137-141
• /
• 2005

A transverse flux, PM-exited linear motor (TFM-LM) with inner mover was designed and built. Its output power density is higher and its weight is lower than those of the conventional PM exited linear synchronous motors (PM LSM). To obtain the maximum thrust force under the given volume, the thrust force density with respect to the ratio of the slot width and the length of pole pitch is analyzed by the 3-dimension finite element method (FEM). Finally, calculated static thrust forces was compared with the experimental values. The calculated and measured performance of the transverse flux, PM-exited linear motor with inner mover revealed great potential for system improvements by reducing the mass of the linear motor. For examples, when this motor was applied to a ropeless elevator, it was possible to increase the power density by more than 400% over the conventional PM-LSM. The results of this study recommend this type of motor for the ropeless elevator or gearless direct linear driving system.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1845-1850
• /
• 2011

Permanent Magnet Synchronous Motor(PM motor) of Advanced EMU is the direct drive morot(DDM) without using reduction gear and Interior buried Permanent Magnet Synchronous Motor(IPMSM). Propulsion system for IPMSM control is composed 1C1M. 1C1M is good for each motor control and anti slip/slide. Propulsion control system have completed running test on field and reliability test is in progress.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.5
• /
• pp.977-983
• /
• 2011

This paper proposes a new adaptive speed controller to achieve a robust speed control of a permanent magnet synchronous motor(PMSM). The proposed adaptive regulator does not require any information on the motor parameter and load torque values, so it is very insensitive to model parameter and load torque variations. Also, the stability of the proposed adaptive control system is proven. To validate the robustness of the proposed adaptive speed controller, both simulation and experimental results are provided under motor parameter and load torque variations. It is clearly demonstrated that the proposed adaptive regulator can accurately control the speed of permanent magnet synchronous motors.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.6
• /
• pp.556-564
• /
• 2013

This paper proposes an initial rotor position detecting algorithm of a PM synchronous motor using an incremental encoder. The proposed algorithm estimates the phase offset between the rotor magnetic flux and the Z-pulse of the incremental encoder by applying six aligning mode current control. The absolute rotor position for driving a PM synchronous motor is calculated by using the phase offset of the Z pulse and A, B pulse signals of the encoder. The PMSM drives based on the estimated rotor position is applied to the elevator door system. The door length is measured on line at first setup of the elevator. The speed control for open, close, and reopen of the elevator door is also presented and the proposed algorithm for the elevator door system is verified by experiment.

• Journal of Power Electronics
• /
• v.17 no.5
• /
• pp.1223-1230
• /
• 2017

The back emf harmonics of a permanent magnet (PM) synchronous motor is a major source of torque ripple. For torque control applications including column fitted MDPS (motor driven power steering) systems, it is essential to reduce the mechanical vibrations due to torque ripples at low speeds. In this paper, a torque ripple reduction algorithm for interior PM synchronous motors is proposed. The harmonic currents that cancel the $6^{th}$ order torque harmonic are added to the nominal dq currents for MTPA (maximum torque per ampere) operation. The compensated harmonic currents are derived from flux linkage harmonics based on a FFT analysis of the back emf harmonics. Simulation and experimental results verify that the $6^{th}$ order torque harmonic and THD of the torque ripple are reduced by compensating the dq harmonic currents.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.3
• /
• pp.216-222
• /
• 2017

The rotor position of a PM synchronous motor is commonly estimated from the mathematical model for the sensorless control without rotor position sensors. For the magnet flux-based rotor position estimator in the stationary reference frame, the magnet flux estimator for estimating rotor position and speed includes the integrator. The integrator in the magnet flux estimator may accumulate the offset of the current sensors and the voltage drift. This continuous accumulation of the offset may cause the drift and overflow in the integrator, such that the estimated rotor position and speed may fail to track the real rotor position and speed. In this paper, the magnet flux estimator without integrator is proposed to avoid overflow in the integrator. The proposed rotor position and speed estimator based on magnet flux estimator are verified through simulation and experiment.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.334-336
• /
• 1995

An adaptive feedback linearization technique of a PM synchronous motor with specified output dynamic performance is proposed. The adaptive parameter estimation is achieved by a model reference adaptive technique where the stator resistance and flux linkage can be estimated with the current dynamic model and the state observer. Using these estimated parameters, the linearizing control inputs are calculated and a nonlinear coupled model of a PM synchronous motor is input-output linearized. The resultant model has the load torque disturbance. To get ti perfect decoupled model, the load torque is estimated. The adaptation laws are derived by the hyperstability theory and positivity concept. The robustness of the proposed control scheme will be proven through the computer simulations.