• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2003년도 추계총회 및 연구발표회 초록집
• /
• pp.128.2-128
• /
• 2003

• 한국수소및신에너지학회논문집
• /
• 제15권4호
• /
• pp.291-300
• /
• 2004

Performance of PEMFC is affected by many factors such as that of MEA, configuration of flow field, operating conditions, humidification, cooling and so on. In this study, in order to improve the performance of fuel cell, a small area fuel cell stack was made and its performance was tested under various operating conditions. Stack consists of 3 single PEM fuel cells. Channel is serpentine type and the active area of the electrode is $50cm^2$. The test results show that the peak power is 60W at $70^\circ{C}$ of stack temperature with humidification condition.

• Journal of Microbiology and Biotechnology
• /
• 제26권12호
• /
• pp.2171-2178
• /
• 2016

Polyester cloth (PC) was selected as a prospective inexpensive substitute separator material for microbial fuel cells (MFCs). PC was compared with a traditional Nafion proton exchange membrane (PEM) as an MFC separator by analyzing its physical and electrochemical properties. A single layer of PC showed higher mass transfer (e.g., for $O_2/H^+/ions$) than the Nafion PEM; in the case of oxygen mass transfer coefficient ($k_o$), a rate of $50.0{\times}10^{-5} cm{\cdot}s^{-1}$ was observed compared with a rate of $20.8{\times}10^{-5}cm/s$ in the Nafion PEM. Increased numbers of PC layers were found to reduce the oxygen mass transfer coefficient. In addition, the diffusion coefficient of oxygen ($D_O$) for PC ($2.0-3.3{\times}10^{-6}cm^2/s$) was lower than that of the Nafion PEM ($3.8{\times}10^{-6}cm^2/s$). The PC was found to have a low ohmic resistance ($0.29-0.38{\Omega}$) in the MFC, which was similar to that of Nafion PEM ($0.31{\Omega}$); this resulted in comparable maximum power density and maximum current density in MFCs with PC and those with Nafion PEMs. Moreover, a higher average current generation was observed in MFCs with PC ($104.3{\pm}15.3A/m^3$) compared with MFCs with Nafion PEM ($100.4{\pm}17.7A/m^3$), as well as showing insignificant degradation of the PC surface, during 177 days of use in swine wastewater. These results suggest that PC separators could serve as a low-cost alternative to Nafion PEMs for construction of cost-effective MFCs.

• 한국수소및신에너지학회논문집
• /
• 제24권1호
• /
• pp.50-60
• /
• 2013

High temperature proton exchange membrane fuel cells (PEMFCs) using phosphoric acid (PA) doped polybenzimidazole (PBI) membranes have been concentrated as one of solutions to the limits with traditional low temperature PEMFCs. However, the amount of reported experimental data is not enough to catch the operational characteristics correlated with cell performance and durability. In this study, design of experiments (DOE) based operational optimization method for high temperature PEMFCs has been proposed. Response surface method (RSM) is very useful to effectively analyze target system's characteristics and to optimize operating conditions for a short time. Thus RSM using central composite design (CCD) as one of methodologies for design of experiments (DOE) was adopted. For this work, the statistic models which predict the performance and degradation rate with respect to the operating conditions have been developed. The developed performance and degradation models exhibit a good agreement with experimental data. Compared to the existing arbitrary operation, the expected cell lifetime and average cell performance during whole operation could be improved by optimizing operating conditions. Furthermore, the proposed optimization method could find different new optimal solutions for operating conditions if the target lifetime of the fuel cell system is changed. It is expected that the proposed method is very useful to find optimal operating conditions and enhance performance and durability for many other types of fuel cell systems.

• 멤브레인
• /
• 제32권5호
• /
• pp.292-303
• /
• 2022

이산화탄소 배출이 없는 고분자 전해질 막 연료전지(polymer electrolyte membrane fuel cell, PEMFC)는 수송용, 발전용 시스템에 적용 가능한 친환경 에너지 변환장치이다. PEMFC의 주요 구성품 중 하나인 고분자 전해질 막(polymer electrolyte membrane, PEM)은 구동시간 동안의 높은 수소 이온 전도도와 물리화학적 안정성 갖춘 과불소화계 고분자(perfluorinated sulfonic acid, PFSA) 기반 PEM (PFSA-PEM)이 상용화 되어있다. 하지만 PFSA-PEM의 단점으로 지적되는 낮은 유리전이온도와 높은 기체 투과도의 보완이 요구되고 있다. 이에 본 총설에서는 PFSA-PEM의 성능 향상 및 단점 보완을 위해 1) PFSA의 측쇄부 길이를 조절함으로써 이온교환용량의 증가와 고분자의 결정성을 증가시켜 PFSA-PEM의 능력을 향상시킨 연구와 2) 유/무기 첨가제를 도입하여 수소 이온 전도도 및 물리적 안정성을 향상시키는 복합 막 연구 및 3) 다공성 지지체를 도입하여 PEM의 두께를 효과적으로 감소시켜 막 저항을 효과적으로 줄이고 내구성을 큰 폭으로 개선한 다공-충진막에 관한 연구를 소개하고자 한다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.76.2-76.2
• /
• 2010

The gas diffusion layer is the key component of the proton exchange membrane fuel cell because it directly affect to the mass transport mechanism and dynamic behavior of the cell. In this study, the effects of GDL aging on the transient response of the PEM fuel cell is systematically investigated using current step transient response analysis under different stoichiometric ratios and humidity conditions. With GDLs aged by the accelerated stress test, the effects of hydrophobicity and structural changes due to carbon loss in the GDL on the transient response of PEM fuel cells are determined. The degraded GDLs that had uneven hydrophobicity distributions cause local water flooding inside the GDL and induce lower and unstable voltage responses after load changes.

• Journal of Electrochemical Science and Technology
• /
• 제8권1호
• /
• pp.7-14
• /
• 2017

This study aims to examine the influences of substrates/diffusion layers (DL) and oxygen reduction reaction catalysts ($M_{ORR}$) on the performance of $M_{ORR}/IrO_2$/DL-type bifunctional oxygen electrodes for use in polymer electrolyte membrane (PEM)-type unitized regenerative fuel cells (URFC). The $M_{ORR}/IrO_2$/DL electrodes were prepared via two sequential steps: anodic electrodeposition of $IrO_2$ on various DLs and fabrication of $M_{ORR}$ layers (Pt, Pd, and Pt-Ru) by spraying on $IrO_2/DL$. Experiments using different DLs, with Pt as the $M_{ORR}$, revealed that the roughness factor of the DL mainly determined the electrode performance for both water electrolyzer (WE) and fuel cell (FC) operations, while the contributions of porosity and substrate material were insignificant. When Pt-Ru was utilized as the $M_{ORR}$ instead of Pt, WE performance was enhanced and the electrode performance was assessed by analyzing round-trip efficiencies (${\varepsilon}_{RT}$) at current densities of 0.2 and $0.4A/cm^2$. As a result, using Pt-Ru instead of Pt alone provided better ${\varepsilon}_{RT}$ at both current densities, while Pd resulted in very low ${\varepsilon}_{RT}$. Improved efficiency was related to the additional catalytic action by Ru toward ORR during WE operation.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2008년도 추계학술대회 논문집
• /
• pp.193-195
• /
• 2008

As arising the cost and decreasing of gasoline and fossil fuel, renewable energy sources such as photovoltaics, wind and fuel cell have been interested. Among of them, PEM fuel cells are good energy sources to provide reliable power at steady state regardless of weather, time of day and location as long as the fuel and air are supplied, but they cannot respond to electrical load transients as fast as desired. This is mainly due to their slow internal electrochemical and thermodynamic responses. Therefore, to use the fuel cells with high efficiency, this paper finds characteristic curve and understand operation of PEMFC based on three theoretical approaches such as activation, ohmic and concentration and make the model using MATLAB. That result was compared with real system to certify.

• 한국수소및신에너지학회논문집
• /
• 제24권1호
• /
• pp.61-69
• /
• 2013

Polymer exchange membrane (PEM) fuel cells have multifunctional properties, and bipolar plates are one of the key components in these fuel cells. Generally, a bipolar plate has a gas flow path for hydrogen and oxygen liberated at the anode and cathode, respectively. In this study, the influence of iodine applied to a bipolar plate was investigated. Accordingly, we compared bipolar plates with and without iodine coating, and the performances of these plates were evaluated under operating conditions of $75^{\circ}C$ and 100% relative humidity. The membrane and platinum-carbon layer were affected by the iodine-coated bipolar plate. Bipolar plates coated with iodine and a membrane-electrode assembly (MEA) were investigated by electron probe microanalyzer (EPMA) and energy-dispersive x-ray spectroscopy (EDS) analysis. Polarization curves showed that the performance of a coated bipolar plate is approximately 19% higher than that of a plate without coating. Moreover, electrochemical impedance spectroscopy (EIS) analysis revealed that charge transfer resistance and membrane resistance decreased with the influence of the iodine charge transfer complex for fuel cells on the performance.

• 한국가스학회지
• /
• 제23권6호
• /
• pp.33-38
• /
• 2019

제조식 수소충전소에서 생산되는 수소가스는 일반적으로 석탄연료의 개질 및 부생가스 등을 활용하지만 순수물을 활용한 수전해 기술의 경우 청정한 기술로 각광 받고 있다. 전기에너지를 이용하여 순수한 물로부터 수소를 생산하는 기술 중에는 향후 가격 및 성능 경쟁에서 우수한 PEM(Polymer Electrolyte Membrane electrolysis)을 이용한 개발이 주로 이루어지고 있다. 이에 본 연구에서는 국내 수소충전소 중 개발단계에 있는 PEM 수전해 수소충전소에 대해 잠재된 유해위험요소를 확인하여 안전한 수소생산 및 수소충전소의 활성화를 도모하고자 한다. 유해위험요소를 도출하기 위해서는 수전해 수소충전소의 설비 및 장치의 안전성이 우선 확보되어야하기에 FMEA(Failure Mode & Effect Analysis)를 수행함으로써 수전해 및 수소충전소의 설비에서의 유해위험요인을 분석하였다.