• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.882-885
• /
• 2018

Recently, signal integrity on PCB (printed circuit board) becomes very important as the system operation speed increases. So far, PCB is customarily designed to minimize area and cost. However, ultra-high-speed PCB often fail to operate properly, unless it is precisely and carefully designed considering dielectric characteristics, line width, line spacing, and impedance matching. This paper surveys many problems in ultra-high-speed PCB and various design methods to mitigate them.

• Journal of the Korea Safety Management & Science
• /
• v.15 no.2
• /
• pp.129-134
• /
• 2013

In this study, the heat flow analysis compatible commercial code CFX 11 was used to develop the structure inside PCB circuit board devices, which could stable radiant heat as well as the cooling device within it. In case of modifying the arrangement of electronic parts on the PCB inside the multi channel temperature measurement board devices, radiant heat effects did not show a rising tendency, whereas the overall temperature went down in case of installing the vents in the outer case of PCB circuit board devices. In terms of installation location, it was the most appropriate to install it on the electronic parts with no heat. Besides, in case of mounting the fan as a cooling device by considering various user environments for multi channel temperature measurement board devices, the radiant heat effects were shown higher than in case of installing the vents, and the middle sections were the most appropriate to its installation location. In case of changing the wind quantity of the fan from its selected installation location, the best radiant heat effects were shown at high speed as expected.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.6
• /
• pp.1967-1971
• /
• 2012

A hexavalent chromium (Cr (VI)) is one of the hazardous substances regulated by the RoHS. The determination of Cr (VI) in various polymers and printed circuit board (PCB) has been very important. In this study, the three different analytical methods were investigated for the determination of a hexavalent chromium in Acrylonitrile Butadiene Styrene copolymer (ABS) and PCB. The results by three analytical methods were obtained and compared. An analytical method by UV-Visible spectrometer has been generally used for the determination of Cr (VI) in a sample, but a hexavalent chromium should complex with diphenylcarbazide for the detection in the method. The complexation did make an adverse effect on the quantitative analysis of Cr (VI) in ABS. The analytical method using diphenylcarbazide was also not applicable to printed circuit board (PCB) because PCB contained lots of irons. The irons interfered with the analysis of hexavalent chromium because those also could complex with diphenylcarbazide. In this study, hexavalent chromiums in PCB have been separated by ion chromatography (IC), then directly and selectively detected by inductively coupled plasma atomic emission spectrometry (ICP-AES). The quantity of Cr (VI) in PCB was 0.1 mg/kg.

• Korean Journal of Computational Design and Engineering
• /
• v.9 no.4
• /
• pp.416-424
• /
• 2004

In this paper, the heat transfer analysis and thermal stress analysis of the PCB(Printed Circuit Board) equipped in electronic Packages are carried out for various may types of chips on the PCB. And two structural PCB models are used in the analyses. The electronic chips on the PCB usually emit heat and this heat generates the thermal stress around the chip. The thermal load due to the heat generation of chips on the PCB may cause the malfunction of the electronic packages such as a monitor. a computer etc. Hence, the PCB should be designed to withstand these thermal loads. In this paper, the heat transfer analysis and thermal stress analysis are executed for the PCB model with pins and the analysis results are compared with the results for the PCB model without pins. The analysis results show that the PCB model without pins is not good for the thermal stress analysis of PCB, even though these two models have similar heat transfer characteristics. The analysis results also show that the highest thermal stress occurs in the pin especially attached to the highest temperature chip, and the PCB constrained to the electronic package on the long side is structurally more stable than other cases. The analyses of the PCB are executed using the finite element analysis code, NISA.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.874-877
• /
• 2018

Many SMDs (surface mount device) are mounted and mutually connected on a PCB (printed circuit board). System performance degrades when their transmission characteristics are bad. Pads connecting a PCB and SMDs affects PCB transmission characteristics significantly, so pad should be properly aligned to optimize impedance matching. In this paper, effects on PCB transmission characteristics are simulated by pad alignment. When frequency is relatively low, pad alignment seldom affect PCB transmission characteristics, but it affects more and more when frequency or pad size becomes larger. Therefore, pad alignment should be carefully chosen based on target frequency and pad size. Especially, the proposed edge-aligned pad is generally more advantageous over the conventional centered-aligned pad in 12~16 GHz Ku-band frequency.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.78-81
• /
• 2002

Printed Circuit Boards for satellite are composed of multi-layered copper plate and glass epoxy. Each copper layer have the complicated and different pattern to operate correctly for its mission. Especially. copper layer give effect on the PCB stiffness seriously. But It can make more complicate to predict the exact stiffness of PCB. In KOMPSAT-2 program, too many type of PCB are used for each electronic unit, and they have different type of pattern of copper layer. Solar array regulator has two type of PCB and it will be considered for this study. In this study. we calculate the PCB board stiffness of KOMPSAT-2 SAR unit considering the concept of simplified representative volume element. It will be correlated with the test results under KOMPSAT-2 vibration environmental condition to increase the reliability of this study.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.5
• /
• pp.89-96
• /
• 2007

Inkjet printing has become one of the most attractive manufacturing techniques in industry. Especially inkjet printing technology will soon be part of the PCB (Printed Circuit Board) fabrication processes. Traditional printing on PCB includes screen printing and photolithography. These technologies involve high costs, time-consuming procedures and several process steps. However, by inkjet technology manufacturing time and production costs can be reduced, and procedures can be more efficient. PCB manufacturers therefore willingly accept this inkjet technology to the PCB industry, and are quickly shifting from conventional to inkjet printing. To produce the printed circuit board by the inkjet technology, it must be harmonized with conductive nano ink, printing process, system, and inkjet printhead. In this study, micro patterning of conductive line has been investigated using the piezoelectric printhead driven by a bipolar voltage signal is used to dispense 20-40 ${\mu}m$ diameter droplets and silver nano ink which consists of 1 to 50 nm silver particles that are homogeneously suspended in an organic carrier. To fabricate a conductive line used in PCB with high precision, a printed line width was calculated and compared with printing results.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.05a
• /
• pp.674-675
• /
• 2016

In this paper, we propose a manufacturing process model of Internet of Things devices using a Printed Circuit Board (PCB)-mounted RFID tag chip for reducing electronic wastes. Electrical and electronic products require a PCB surface mount and many examination. Also, conventional barcode systems cannot provide traceability management in PCB manufacturing before finishing Surface Mount Technology (SMT) process. The proposed process model does not require workers' attaching and detaching process unlike barcode systems. Also, RFID tag chip can record all the data in manufacturing steps. Thus, the number of connections to a database management system (DBMS) can be reduced.

• Proceedings of the IEEK Conference
• /
• 2000.06e
• /
• pp.9-12
• /
• 2000

This paper describes the modeling and experimental results of coreless printed circuit board (PCB) based transformer that can be used for power conversion at high frequency operation. The principle of using coreless PCB based transformer in 2MHz, 10W class ZVS Flyback DC-DC converter has been successfully demonstrated. The maximum power conversion efficiency is 79%. Even for high operating frequency, an efficiency greater than 70% can be obtained with under 1% regulation error.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1992.04b
• /
• pp.159-168
• /
• 1992

생산라인의 line balancing이 흐름생산에 있어서 일관된 생산을 하기 위한 필수조건이다. 여러 다양한 제품을 생산하는 printed circuit board(PCB) 공장에서의 line balancing을 얻기 위해서는 mixed model line balancing절차를 설명하고자 한다.