• Transactions on Electrical and Electronic Materials
• /
• 제12권6호
• /
• pp.267-270
• /
• 2011

In the process of inkjet-printed zinc tin oxide thin-film transistor, the effect of metallic interlayer underneath of source and drain electrode was investigated. The reason for the improved electrical properties with thin molybdenum oxide ($MoO_3$) layer was due to the chemically intermixed state of metallic interlayer, aluminum source and drain, and oxide semiconductor together. The atomic configuration of three Mo $3d_3$ and $3d_5$ doublets, three different Al 2p core levels, two Sn $3d_5$, and four different types of oxygen O 1s in the interfaces among those layers was confirmed by X-ray photospectroscopy.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.166-166
• /
• 2010

Recently, TFTs based on amorphous oxide semiconductors (AOSs) such as ZnO, InZnO, ZnSnO, GaZnO, TiOx, InGaZnO(IGZO), SnGaZnO, etc. have been attracting a grate deal of attention as potential alternatives to existing TFT technology to meet emerging technological demands where Si-based or organic electronics cannot provide a solution. Since, in 2003, Masuda et al. and Nomura et al. have reported on transparent TFTs using ZnO and IGZO as active layers, respectively, much efforts have been devoted to develop oxide TFTs using aforementioned amorphous oxide semiconductors as their active layers. In this thesis, I report on the performance of thin-film transistors using amorphous indium gallium zinc oxides for an active channel layer at room temperature. $SiO_2$ was employed as the gate dielectric oxide. The amorphous indium gallium zinc oxides were deposited by RF magnetron sputtering. The carrier concentration of amorphous indium gallium zinc oxide was controlled by oxygen pressure in the sputtering ambient. Devices are realized that display a threshold voltage of 1.5V and an on/off ration of > $10^9$ operated as an n-type enhancement mode with saturation mobility with $9.06\;cm^2/V{\cdot}s$. The devices show optical transmittance above 80% in the visible range. In conclusion, the fabrication and characterization of thin-film transistors using amorphous indium gallium zinc oxides for an active channel layer were reported. The operation of the devices was an n-type enhancement mode with good saturation characteristics.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.162-162
• /
• 2010

InSb has received great attentions as a promising candidate for the active layer of infrared photodetectors due to the well matched band gap for the detection of $3{\sim}5\;{\mu}m$ infrared (IR) wavelength and high electron mobility (106 cm2/Vs at 77 K). In the fabrication of InSb photodetectors, passivation step to suppress dark currents is the key process and intensive studies were conducted to deposit the high quality passivation layers on InSb. Silicon dioxide (SiO2), silicon nitride (Si3N4) and anodic oxide have been investigated as passivation layers and SiO2 is generally used in recent InSb detector fabrication technology due to its better interface properties than other candidates. However, even in SiO2, indium oxide and antimony oxide formation at SiO2/InSb interface has been a critical problem and these oxides prevent the further improvement of interface properties. Also, the mechanisms for the formation of interface phases are still not fully understood. In this study, we report the quantitative analysis of indium and antimony oxide formation at SiO2/InSb interface during plasma enhanced chemical vapor deposition at various growth temperatures and subsequent heat treatments. 30 nm-thick SiO2 layers were deposited on InSb at 120, 160, 200, 240 and $300^{\circ}C$, and analyzed by X-ray photoelectron spectroscopy (XPS). With increasing deposition temperature, contents of indium and antimony oxides were also increased due to the enhanced diffusion. In addition, the sample deposited at $120^{\circ}C$ was annealed at $300^{\circ}C$ for 10 and 30 min and the contents of interfacial oxides were analyzed. Compared to as-grown samples, annealed sample showed lower contents of antimony oxide. This result implies that reduction process of antimony oxide to elemental antimony occurred at the interface more actively than as-grown samples.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1442-1444
• /
• 1995

In this study, we confirmed that the crystallinity and the mechanical properties of polycrystalline Silicon(poly-Si) deposited on the poly-oxide are better than those of poly-Si on the conventional sacrificial layers that is CVD oxide layer or PSG. But the etch rate of poly-oxide is poor than that of the CVD oxide layer or PSG. Therefore, to make the best use of small stress and fast etch rate, we fabricated the double oxide layer; 10%-thick poly-oxide on 90%-thick CVD oxide or PSG. To estimate structure deformation by stress, we fabricated the test structures; cantilever. bridge and ring/beam structure and estimated by SEM. As the results, all structure is expressed the deformed structure by residual stress(tensile stress) and the deformation of the structure layer on the double oxide layer is small compared with that of the structure layer on the CVD oxide layer or PSG. And, the etch rate of the double oxide layer is enhanced compared with that of the poly-oxide.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(2)
• /
• pp.29-32
• /
• 2001

In this paper, the thermal oxidation behaviors and the electrical characteristics of the thermal oxide grown on SiC are discussed. For these studies the oxide layers with various thickness were on SiC in wet $O_2$ or dry $O_2$ at l15$0^{\circ}C$ and the MOS capacitors using the 350$\AA$ gate oxide grown in wet $O_2$ were fabricated and electrically characterized. It was found from the experimental results that the oxidation rate of SiC with the Si-face and with the carbon-face were about 10% and 50% of oxidation rate of Si. The C-V measurement results of the SiC oxide showed abnormal hysterisis properties which had ever been not observed for the Si oxide. And the hysterisis behavior was seen more significant when initial bias voltage was more negative or more positive. The hysterisis property of the SiC oxide was believed to be due the substantial amount of the deep level traps to exist at the interface between the oxide and the SiC substrate. The leakage of the SiC oxide was found to be one order larger than the Si oxide, but the breakdown strength was almost equal to that of the Si oxide.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권10호
• /
• pp.464-468
• /
• 2003

The double layers of $SiO_2$/$Si_3$$N_4$ have superior charge storage stability than a single layer of $SiO_2$. Many researchers are very interested in the charge storage mechanism of $SiO_2$/$Si_3$$N_4$ [1,2]. In this paper, the electrical characteristics of thermal oxide and atmospheric pressure chemical vapor deposition (APCVD) of $Si_4$$N_4$ have been investigated and explained using high frequency capacitance-voltage measurements. Additionally, this paper will describe capacitance-voltage characteristics for double layers of $SiO_2$/$Si_4$$N_4$ by "Athena", a semiconductor device simulation tool created by Silvaco, Inc.vaco, Inc.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.240-240
• /
• 2010

A multiple alloy metal nano-dots memory using FN tunneling was investigated in order to confirm its structural possibility for future flash memory. In this work, a multiple FePt nano-dots device with a high work function (~5.2 eV) and extremely high dot density (${\sim}\;1.2{\times}10^{13}/cm^2$) was fabricated. Its structural effect for multiple layers was evaluated and compared to one with a single layer in terms of the cell characteristics and reliability. We confirm that MOS capacitor structures with 2-4 multiple FePt nano-dot layers provide a larger threshold voltage window and better retention characteristics. Furthermore, it was also revealed that several process parameters for block oxide and inter-tunnel oxide between the nano-dot layers are very important to improve the efficiency of electron injection into multiple nano-dots. From these results, it is expected that a multiple FePt nano-dots memory using Fowler-Nordheim (FN)-tunneling could be a candidate structure for future flash memory.

• Bulletin of the Korean Chemical Society
• /
• 제33권1호
• /
• pp.189-193
• /
• 2012

ZnO nanorods were grown on the $Cd_xZn_{1-x}O$ seed layers with various Cd mole fractions by hydrothermal method. The effects of the Cd mole fraction for $Cd_xZn_{1-x}O$ seed layers on the structural and optical properties of the ZnO nanorods were investigated by scanning electron microscopy, X-ray diffraction, and photoluminescence. The narrowest full-width at half-maximum and largest grain size of the $Cd_xZn_{1-x}O$ seed layers, indicating improvement in crystal quality, were observed at the Cd mole fraction of 0.5. At the Cd mole fraction of 0.5, the largest enhancement in the density, the crystal quality, and the growth rate of the ZnO nanorods was observed while their appearance was not affected significantly by the incorporation of the Cd in the $Cd_xZn_{1-x}O$ seed layers. Consequently, the luminescent properties of the ZnO nanorods were enhanced. The largest improvement in the structural and optical properties of the ZnO nanorods was observed at the Cd mole fraction of 0.5.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.248-248
• /
• 2016

We have investigated the crystallinity, preferential ordering, and interfacial stability of 1,4,5,8,9,11-hexaazatriphenylene-hexanitrile (HATCN) thin film interconnected with organic/inorganic multilayer. At the region close to the organic-organic interface, HATCN formed low crystalline order with substantial amorphous phase. As film growth continued, HATCN stacked with high crystalline phase. After a sputtering deposition of the indium zinc oxide (IZO) layer on top of HATCN/organic layer, the volume fraction of preferentially ordered HATCN crystals increased without any structural deterioration. In addition, the HATCN surface was kept quite stable by preserving the sharp interface between HATCN and sputtering deposited IZO layers.

• 한국분말재료학회지
• /
• 제6권3호
• /
• pp.224-230
• /
• 1999

Oxide powders of $Cr_2O_3 \;and\;Cr_2O_3+3{\%}TiO_2$ were prepared by spray drying, plasma densification and fused+crushed processes. The oxide coating layers were made by plasma spray and characterized by microstructure, hardness, adhesion strength and relative density. The optimum spray distance for the high quality coatings by spraying dried powders was found to be 9cm. A small amount addition of $TiO_2\;in\;Cr_2O_3$ powder significantly improved coating characteristics by lowering the melting point of powders. The hardness and relative density of coating layers of the plasma densified powders were comparable to fused and crushed powders, however, the adhesion strength was much higher in the former case.