• Journal of the Korean institute of surface engineering
• /
• v.52 no.2
• /
• pp.62-71
• /
• 2019

Al1050 and Al7075 alloy specimens were exposed to atmospheric conditions for 24 months and analyzed by Transmission Electron Microscopy to characterize their corrosion behavior and oxide film characteristics, especially focusing on intergranular corrosion or oxidation. In general, the intergranular oxygen penetration depth of Al1050 was deeper than Al7075. Since O and Si signals were overlapped at the oxidized grain boundaries of Al1050 and Mg is not included in Al1050, it is concluded that Si segregated along the grain boundaries directly impacts on the intergranular corrosion of Al1050. Cr-Si or Mg-Si intermetallic particles were not observed along the grain boundaries of Al7050, but Mg-Si particle was barely observed in the matrix. 10-nm size Mg-Zn particles were also found all over the matrix. Mg was mainly observed along the oxidized grain boundary of Al7075, but Si was not detected due to the Mg-Si particle formation in the matrix and relatively low concentration of Si in Al7075. Therefore, it is thought that Mg plays an important role in the intergranular corrosion of Al7075 under atmospheric corrosion conditions.

• Food Science of Animal Resources
• /
• v.39 no.3
• /
• pp.355-370
• /
• 2019

The present study aimed at evaluating effects of traditional sauce type and storage time on shelf-life and flavor compounds of marinated pork cooked by Sous-Vide method. Five different traditional sauces (Meju soy sauce, Brewed soy sauce, Fish-soy sauce, Ishiru fish sauce and Anchovy fish sauce) purchased from Asian countries were used. After marination with the sauces, polyvinylchloride film bags containing the marinated pork samples were cooked using Sous-Vide method for $55^{\circ}C$ for 5 h and $60^{\circ}C$ for 30 min, and were then stored for 8 wk at $10^{\circ}C$. Results showed that the pork samples marinated with the sauces retarded the growth of total plate counts (TPC) during storage. At $8^{th}$ wk storage, TPC counts were significantly lower in all samples marinated with the sauces compared to control (p<0.05). Lipid oxidation level was significantly lower in the T2 (Meju soy sauce) and T6 (Anchovy fish sauce) compared to those of T3 (Brewed soy sauce) and T5 (Ishiru fish sauce) or control after 8 wk storage (p>0.05). Forty volatile flavor compounds were detected from the control and marinated samples at $4^{th}$ wk of storage. The pork marinated with Anchovy fish sauce presented significantly higher amounts of importantly pleasant flavor compounds such as; pyrazines and sulfurcontaining compounds than those marinated with other remaining sauces and control. It is concluded that the marination with Anchovy fish sauce partly improved the shelf-life and increased amounts of pleasant flavor compounds of Sous-Vide cooked pork products during storage in comparison to the other remaining sauces.

• Journal of Sensor Science and Technology
• /
• v.32 no.3
• /
• pp.169-173
• /
• 2023

With the increasing concern of global warming caused by greenhouse gases owing to the recent industrial development, there is a growing need for advanced technology to control these emissions. Among the various greenhouse gases, nitrogen dioxide (NO₂) is a major contributor to global warming and is mainly released from sources, such as automobile exhaust and factories. Although semiconductor-type NO₂ gas sensors, such as SnO₂, have been extensively studied, they often require high operating temperatures and complicated manufacturing processes, while lacking selectivity, resulting in inaccurate measurements of NO₂ gas levels. To address these limitations, a novel sensor using PbS quantum dots (QDs) was developed, which operates at low temperatures and exhibits high selectivity toward NO₂ gas owing to its strong oxidation reaction. Furthermore, the use of P3HT conductive polymer improved the thin film quality, reactivity, and reaction rate of the sensor. The sensor demonstrated the ability to accurately measure NO₂ gas concentrations ranging from 500 to 100 ppm, with a 5.1 times higher sensitivity, 1.5 times higher response rate, and 1.15 times higher recovery rate compared with sensors without P3HT.

• Analytical Science and Technology
• /
• v.19 no.5
• /
• pp.394-399
• /
• 2006

The polishing performance and the relationships of electrochemistry depending upon oxidizers and additives in the tungsten CMP slurry used in semiconductor industry were investigated. Hydrogen peroxide, ferric nitrate and potassium iodate were used as oxidizers and they showed different oxidation reactions on tungsten film depending on the kind of oxidizers and pH of slurry. The differences influenced the polishing performance. Etching reaction was predominated in the hydrogen peroxide. However, passivation reaction was prevailed in ferric nitrate and potassium iodate. TMAH and KOH raised the potential energy and removal rate of tungsten, and improved a dispersion characteristic of slurry by increasing absolute value of zeta potential. Addition of 100 ppm of poly(acrylic acid) of M.W. 250,000 improved dispersion ability.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.33 no.2
• /
• pp.71-79
• /
• 2017

Purpose: Ni-Cr alloy does not contain Beryllium, causing the metal compound to form oxides in the furnace but by using Titanium as a chemical catalyst the forming of the oxides can be controlled, and by controlling the impurities formed on the metal surface, the possibility of the Ni-Cr alloy bond strength being increased can be analysed. Materials and Methods: Titanium was used as a chemical catalyst in the porcelain for the oxidation of beryllium-free metal (Ni-Cr) alloy. The T1 group, which does not use Titanium power as a chemical catalyst is a reference model for comparison. The T2 group and T3 group used 10 g and 20 g of Titanium power, respectively. They are fabricated to observe the shear bond strength and surface properties. There was no significance when One-way ANOVA analysis/Tukey Honestly Significant Difference Test was conducted for statistical analysis among groups (P > 0.05). Results: Results of measuring the three-point flexural bond strength of the Ni-Cr alloy and thickness of the oxide film. Experiment T3 using 20 g Titanium chemical catalyst: $39.22{\pm}3.41MPa$ and $6.66{\mu}m$, having the highest bond strength and thinness of oxide film. Experiment T2 using 10 g Titanium chemical catalyst: $34.65{\pm}1.39MPa$ and $13.22{\mu}m$. Experiment T1 using no Titanium chemical catalyst: $32.37{\pm}1.91MPa$ and $22.22{\mu}m$. Conclusion: The T2 and T3 experiments using Titanium chemical catalyst showed higher bond strength for the Ni-Cr alloy and lower thickness of oxide film than experiment T1, and the titanium catalyst being able to increase bond strength was observed.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.3
• /
• pp.253-261
• /
• 2005

Catalytic wet oxidation of ppm levels of trichloroethylene (TCE) in water has been conducted using $TiO_2$-supported cobalt oxides at a given temperature and weight hourly space velocity. 5% $CoO_x/TiO_2$ might be the most promising catalyst for the wet oxidation at $36^{\circ}C$ although it exhibited a transient behavior in time on-stream activity. Not only could the bare support be inactive for the wet decomposition reaction, but no TCE removal also occurred by the process of adsorption on $TiO_2$ surface. The catalytic activity was independent of all particle sizes used, thereby representing no mass transfer limitation in intraparticle diffusion. Characterization of the $CoO_x$ catalyst by acquiring XPS spectra of both fresh and used Co surfaces gave different surface spectral features of each $CoO_x$. Co $2p_{3/2}$ binding energy of Co species exposed predominantly onto the outermost surface of the fresh catalyst appeared at 781.3 eV, which is very similar to the chemical states of $CoTiO_x$ such as $Co_2TiO_4$ and $CoTiO_3$. The spent catalyst possessed a 780.3 eV main peak with a satellite structure at 795.8 eV. Based on XPS spectra of reference Co compound, the TCE-exposed Co surfaces could be assigned to be in the form of mainly $Co_3O_4$. XRD measurements indicated that the phase structure of Co species in 5% $CoO_x/TiO_2$ catalyst even before reaction is quite comparable to the diffraction lines of external $Co_3O_4$ standard. A model structure of $CoO_x$ present on titania surfaces would be $Co_3O_4$, encapsulated in thin-film $CoTiO_x$ species consisting of $Co_2TiO_4$ and $CoTiO_3$, which may be active for the decomposition of TCE in a flow of water.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.18 no.2
• /
• pp.181-188
• /
• 1989

The present study has been carried out to investigate the effect of Bactokil(made from didecyldimethyl ammonium chloride isopropanol and water) and Taipet-F (made from natural vitamin E, L-ascorbic acid, glyceride and gallic acid) on retarding lipid oxidation in boiled-dried anchovy. To process boiled-dried anchovy, boiled anchovy dried in cabinet drier $(dry-bulb\;temperature\;40^{\circ}C)$ for 1 hour were fronted with the Bactokil, the Taipet-F and mixture of Bactokil and Taipet-F, respectively. Anchovy fronted with chemicals were redried for 8 hours, packed in polyethylene film bag, and then stored at room temperature $(24{\pm}3^{\circ}C)$. These products were compared with control(untreated with chemicals) during storage. The changes in volatile basic nitrogen of each product was negligible during storage. The thiobarbituric acid and peroxide values of each product increased up to 10 days of storage, and then decreased. In color value of each product, L value increased, while n, b and ${\bigtriangleup}E$ values decreased during storage. The changes in brown pigment formation of each product increased up to final stage of storage. From the results of chemical analysis and sensory evaluation, the product treated with Taipet-F(0.5%, v/v) was the most effective on retarding lipid oxidation of the boiled -dried anchovy, followed by the product treated withthe mixture of Bactokil (0.04%, v/v) and Taipet-F (0.5%, v/v), the product treated with Bactokil(0.04%, v/v) and control, in the order named.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.1
• /
• pp.85-97
• /
• 2007

Statement of problem: Recently, anodic oxidation of cp-titanium is a popular method for treatment of titanium implant surfaces. It is a relatively easy process, and the thickness, structure, composition, and the microstructure of the oxide layer can be variably modified. Moreover the biological properties of the oxide layer can be controlled. Purpose: In this study, the roughness, microstructure, crystal structure of the variously treated groups (current, voltage, frequency, electrolyte, thermal treatment) were evaluated. And the specimens were soaked in simulated body fluid (SBF) to evaluate the effects of the surface characteristics and the oxide layers on the bioactivity of the specimens which were directly related to bone formation and integration. Materials and methods: Surface treatments consisted of either anodization or anodization followed thermal treatment. Specimens were divided into seven groups, depending on their anodizing treatment conditions: constant current mode (350V for group 2), constant voltage mode (155V for group 3), 60 Hz pulse series (230V for group 4, 300V for group 5), and 1000 Hz pulse series (400V for group 6, 460V for group 7). Non-treated native surfaces were used as controls (group 1). In addition, for the purpose of evaluating the effects of thermal treatment, each group was heat treated by elevating the temperature by $5^{\circ}C$ per minute until $600^{\circ}C$ for 1 hour, and then bench cured. Using scanning electron microscope (SEM), porous oxide layers were observed on treated surfaces. The crystal structures and phases of titania were identified by thin-film x-ray diffractmeter (TF-XRD). Atomic force microscope (AFM) was used for roughness measurement (Sa, Sq). To evaluate bioactivity of modified titanium surfaces, each group was soaked in SBF for 168 hours (1 week), and then changed surface characteristics were analyzed by SEM and TF-XRD. Results: On basis of our findings, we concluded the following results. 1. Most groups showed morphologically porous structures. Except group 2, all groups showed fine to coarse convex structures, and the groups with superior quantity of oxide products showed superior morphology. 2. As a result of combined anodization and thermal treatment, there were no effects on composition of crystalline structure. But, heat treatment influenced the quantity of formation of the oxide products (rutile / anatase). 3. Roughness decreased in the order of groups 7,5,2,3,6,4,1 and there was statistical difference between group 7 and the others (p<0.05), but group 7 did not show any bioactivity within a week. 4. In groups that implanted ions (Ca/P) on the oxide layer through current and voltage control, showed superior morphology, and oxide products, but did not express any bioactivity within a week. 5. In group 3, the oxide layer was uniformly organized with rutile, with almost no titanium peak. And there were abnormally more [101] orientations of rutile crystalline structure, and bonelike apatite formation could be seen around these crystalline structures. Conclusion: As a result of control of various factors in anodization (current, voltage, frequency, electrolytes, thermal treatment), the surface morphology, micro-porosity, the 2nd phase formation, crystalline structure, thickness of the oxide layer could be modified. And even more, the bioactivity of the specimens in vitro could be induced. Thus anodic oxidation can be considered as an excellent surface treatment method that will able to not only control the physical properties but enhance the biological characteristics of the oxide layer. Furthermore, it is recommended in near future animal research to prove these results.

• Journal of Food Hygiene and Safety
• /
• v.38 no.2
• /
• pp.55-62
• /
• 2023

This study aimed to investigate the effect of a coating agent on pork storage. Pork was coated with a coating agent containing sodium carboxymethyl cellulose (CMC) and mandarin peel powder (M). The treatments were divided into control, a 0.1% CMC treatment, and a 0.1% CMC +5% M treatment, and pH, color, 2-thiobarbituric acid reactive substances (TBARS), volatile basic nitrogen (VBN), and the number of viable cell counts were measured. In the case of redness (a), it was found that the reduction over the storage period was less in the 0.1% CMC + 5% M treatment than in the control and the 1% CMC treatment. When stored at 4℃ and 25℃, TBARS of pork tended to increase during the storage period, followed by control, 0.1% CMC treatment, and 0.1% CMC + 5% M treatment, indicating that lipid oxidation was most suppressed in pork coated with mandarin peel powder. As a result of measuring the VBN of pork stored at 4℃ and 25℃, the 0.1% CMC + 5% M treatment showed lower values than the control and 0.1% CMC treatment. When the film-coated pork was stored at 4℃, the number of viable cell counts in the 0.1% CMC +5% M treatment area was 7.13±0.96 log CFU/g on the 12th day of storage, delaying the growth of viable cell counts for approximately 3 d more than other treatments. Therefore, coating pork with a film containing CMC and mandarin peel powder has been confirmed to delay the increase in the number of viable cell counts while reducing the quality change during pork storage, which is an effective alternative to improving the storage of fresh food as an edible film.

• Applied Chemistry for Engineering
• /
• v.21 no.1
• /
• pp.52-57
• /
• 2010

Although chemical sedimentation and ion exchange are usually applied to the treatment of heavy metal ions and radioactive cations, they have some serious disadvantages like a great consumption of chemicals, the disposal of valuable metals, and the secondary pollution of soil by the solid-waste. The advanced countries recently have studied the electrochemical ion exchange, combined electrochemical reduction and ion exchange, for the development of the alternative technique. This study has been performed to investigate the optimum condition for the preparation of the nickel hexacyanoferrate (NiHCNFe) which is an electrochemical ion exchanger. NiHCNFe film was deposited on the surface of nickel plate by chemical method or electrochemical method. The morphology and composition of NiHCNFe were observed by SEM and EDS, respectively. The peak current density of NiHCNFe was measured from the cyclic voltammograms of the continuous oxidation-reduction reaction in a parallel plane ion exchange electrode reactor. It was found that the chemical preparation method was better than the electrochemical method. The concentrated NiHCNFe was apparently deposited on nickel plate when dipping in the preparing solution for 118 h, especially. It also had a best durable performance as an ion exchange electrode.