• Journal of Food Hygiene and Safety
• /
• v.37 no.5
• /
• pp.356-363
• /
• 2022

To investigate the functional activity of different citrus fruit peels, antioxidant compounds in 70% ethanol extracts of mandarin, lemon, orange, and grapefruit peel powders were identified, and antioxidant and antibacterial activities were quantitated. Mandarin peel contained the highest content of total phenolic compounds and total flavonoid substances (21.46±0.12 mg GAE/g and 11.57±0.05 mg RE/g, respectively). The total phenolic compound content of the three other citrus fruits was 14.16±0.18-18.44±0.07, and their total flavonoid content was 5.51±0.10-7.46±0.09 mg RE/g. DPPH radical scavenging activity was the highest in lemon peel (87.64±0.21%), and mandarin peel displayed the best antioxidant activity with respective ABTS radical scavenging activity and FRAP measurements of 43.20±0.61% and 78.82±1.06 mM TE/g. Grapefruit peel antimicrobial activity increased with treatment time, and was the most potent among the four tested citrus species, inhibiting Staphylococcus aureus by about 4.05 log cycle. These findings demonstrate that mandarin and grapefruit peel can be used to prevent oxidation, improve food storage capabilities, and potentially preserve food quality.

• Journal of Applied Biological Chemistry
• /
• v.65 no.3
• /
• pp.189-194
• /
• 2022

In this study, a sesame meal was used in order to analyze the proximate composition and mineral contents. The sesame seed meal, pressed from roasted Sesame seed, contains various polyphenols. The defatted sesame meal was extracted using 70% ethanol, and its antioxidant activity and antidiabetic effects were evaluated. Proximate composition of sesame meal was showed that moisture 6.51%, carbohydrate 16.22%, crud protein 46.30%, ash 9.88%, crude fat 21.09%. Mineral contents were K 1128.08 mg/100 g, Ca 1356.27 mg/100 g, Fe 12.29 mg/100 g, P 2022.14 mg/100 g, Cu 2.08 mg/100 g, Mg 643.40 mg/100 g, Na 7.29 mg/100 g. The results showed the sesame meal of 70% ethanol extract had higher polyphenol content (184.98 mg GAE/g) and flavonoid content (27.63 mg QE/g). The 2,2-diphenyl-1-picrylhydra-zyl and 2,2'-aziono-bis(3-ethylbenzthiazoline-6-sulfonic acid radical scavenging activities of defatted sesame meal (IC₅₀ ) were 891.84 and 340.09 ㎍/mL. According to the test results, the defatted sesame meal extracted using 70% ethanol had significant antioxidant activity and inhibitory ability to diabetes-related enzymes, indicating that it has good potential as a functional food or nutritional food for prevention and treatment of oxidation.

• Applied Chemistry for Engineering
• /
• v.33 no.2
• /
• pp.188-194
• /
• 2022

This work presents a non-destructive and straightforward approach to assemble a large-scale conductive electronic film made of a pre-treated single-walled carbon nanotube (SWCNT) solution. For effective electron transfer between the immobilized enzyme and SWCNT electronic film, we optimized the pre-treatment step of SWCNT with p-terphenyl-4,4"-dithiol and dithiothreitol. Glucose oxidase (GOx, a model enzyme in this study) was immobilized on the SWCNT electronic film following the positively charged polyelectrolyte layer deposition. The glucose detection was realized through effective electron transfer between the immobilized GOx and SWCNT electronic film at the negative potential value (-0.45 V vs. Ag/AgCl). The SWCNT electronic film-based glucose biosensor exhibited a sensitivity of 98 ㎂/mM·cm². In addition, the SWCNT electronic film biosensor showed the excellent selectivity (less than 4 % change) against a variety of redox-active interfering substances, such as ascorbic acid, uric acid, dopamine, and acetaminophen, by avoiding co-oxidation of the interfering substances at the negative potential value.

• Journal of Applied Biological Chemistry
• /
• v.65 no.4
• /
• pp.457-462
• /
• 2022

Manganese (Mn) exists in various oxidation states and Mn(II) is the most mobile species of Mn, which is toxic to plants and limits their growth. Therefore, the purpose of this study was to reduce Mn toxicity by immobilizing Mn using various adsorbents including iron oxides and calcium compounds. Ferrihydrite, schwertmannite, goethite were synthesized, which was confirmed by X-ray diffraction. Hematite was purchased and used as Mn adsorbent. Calcium compounds such as CaNO₃, CaSO₄, and CaCO₃ were used to increase pH and oxidize Mn. For Mn adsorption, Mn(II) solution was reacted with four iron oxides, CaNO₃, CaSO₄, and CaCO₃ for 24 hours, filtered, and the remaining Mn concentrations in the solution were analyzed by inductively coupled plasma optical emission spectroscopy. The adsorption rate and adsorption isotherm were calculated. Among iron oxides, the adsorption rate was highest for hematite followed by ferrihyrite, but goethite and schwertmannite did not adsorb Mn. In the case of calcium compounds, the adsorption rate was high in the order of CaCO₃>CaNO₃>CaSO₄. In conclusion, treatment of CaCO₃ was the most effective in reducing Mn toxicity by increasing pH.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.4
• /
• pp.86-90
• /
• 2023

The packaging of electronic devices performs a protective function to ensure that their durability and reliability are not affected by changes in the operating environment caused by external factors. Recent advances in materials have led to ongoing research into bonded packaging of heterogeneous materials such as polymers and inorganic materials in electronic devices. In this packaging process, it is important to have a binding that joins the materials and ensures the operating environment, which includes adhesion to the substrate, corrosion and oxidation resistance through moisture removal, and durability. In this study, the hygroscopicity of the coating layer by modifying the polymer surface based on PVA was evaluated by controlling and measuring the contact angle, and the adhesion was confirmed by applying water-based ink and testing according to ASTM_D3363. For the durability of the polymer surface, the IPL post-treatment process was used to improve the hardness and toughness against applied voltage, and the pencil hardness test and nanoindentation test were conducted. Through this, we analyzed and proposed solutions to ensure the reliability and durability of polymer devices in polymer microfabrication against environmental factors such as moisture, temperature fluctuations and adhesion, and surface abrasion.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.4
• /
• pp.98-104
• /
• 2023

The feasibility of an efficient process proposed for Cu-Cu flip-chip bonding was evaluated by forming a porous Cu layer on Cu pillar and conducting thermo-compression sinter-bonding after the infiltration of a reducing agent. The porous Cu layers on Cu pillars were manufactured through a three-step process of Zn plating-heat treatment-Zn selective etching. The average thickness of the formed porous Cu layer was approximately 2.3 ㎛. The flip-chip bonding was accomplished after infiltrating reducing solvent into porous Cu layer and pre-heating, and the layers were finally conducted into sintered joints through thermo-compression. With reduction behavior of Cu oxides and suppression of additional oxidation by the solvent, the porous Cu layer densified to thickness of approximately 1.1 ㎛ during the thermo-compression, and the Cu-Cu flip-chip bonding was eventually completed. As a result, a shear strength of approximately 11.2 MPa could be achieved after the bonding for 5 min under a pressure of 10 MPa at 300 ℃ in air. Because that was a result of partial bonding by only about 50% of the pillars, it was anticipated that a shear strength of 20 MPa or more could easily be obtained if all the pillars were induced to bond through process optimization.

• Food Science and Preservation
• /
• v.30 no.1
• /
• pp.122-131
• /
• 2023

Persimmon peels are mostly discared as a by-product of dried persimmon manufacturing, but effective use is required as it contains various functional constituents. This study covers the preparation of carotenoid-enriched oil by ultrasound treatment of persimmon peel in soybean oil solvent, and the investigation of its physicochemical characteristics. Using the Box-Behnken design and response surface methodology, the optimal extraction conditions (temperature, 62℃; time, 32 min; and persimmon peel to oil ratio, 1:3.1) were determined based on the carotenoid concentration of the extract. The physicochemical characteristics of the extract obtained under optimal conditions and the untreated soybean oil (control) were compared. The total carotenoid content of the extract increased. The carotenoid-enriched soybean oils had a lighter color than the controls, but with high redness and yellowness values. The effect of sonication and a component of the persimmon peel on the oxidation and heating stability of soybean oil was weak. The viscosity and activation energy of carotenoid-enriched soybean oil were slightly higher than those of the control. Thus, it was possible to prepare yellow-red carotenoid-enriched soybean oil by applying ultrasonic-soybean oil solvent extraction to persimmon peel. The oil is expected to be useful as an additive as well as a substitute for general edible oils.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.3
• /
• pp.103-107
• /
• 2024

In this study, nickel, a pure metal material, was proposed as a saggar for synthesizing NCM [Li(Ni_xCo_yMn_z)O₂] cathode active material. Nickel is known as a metal that is resistant to oxidation and has a high melting point. Nickel is one of the main components of NCM cathode material and was expected to be free from problems with contamination from saggar during cathode material synthesis. We sought to confirm the possibility of nickel as a saggar for synthesizing NCM cathode active materials. When a Ni metal crucible and Ni_0.8Co_0.1Mn_0.1(OH)₂ (NCM 811) precursor material were reacted at 900℃ for a long time, the change in the reaction layer on the surface of the crucible over time was analyzed. The nickel crucible reaction layer formed during heat treatment at 900℃ was nickel oxide, and is thought to have been created by simultaneous oxygen diffusion from the cathode precursor oxide and reaction with oxygen in the atmosphere. The change in thickness of the oxide layer appears to slow down after 480 hours, which suggests that the rate of oxygen diffusion from the precursor is reduced. It remained combined without falling out of the crucible until 480 hours. However, it was confirmed that the oxide layer falls off after 720 hours, so it is thought that it can be used as saggar for NCM synthesis only for a certain period of time.

• Korean Chemical Engineering Research
• /
• v.62 no.3
• /
• pp.233-237
• /
• 2024

This study is about the fabrication of a flexible electrode based on PAN-based carbon fibers tow using organic/inorganic nanocomposite and its application of non-enzymatic sensor. The organic/inorganic nanocomposite was composed of the conductive polymer polyaniline (PANI) and the metal oxide CuO. And glucose was used as the target of the electrochemical sensor. Commercialized CFTs were pretreated through heat treatment for desizing and electrochemical oxidation for activation. This nanocomposite was sequentially synthesized on the pretreated CFT surface using electrochemical polymerization and electrochemical deposition. Finally, the CFT/PANI/CuO NPs electrode was obtained. The electrochemical properties and sensing performance of the CFT/PANI/CuO NPs electrode were analyzed using chronoamperometry (CA), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The sensitivity of the CFT/PANI/CuO NPs electrode was about 8.352 mA/mM (in a linear range of 0.445~6.674 mM) and 3.369 mA/mM (in a linear range of 6.674~50 mM), respectively. So, the CFT/PANI/CuO NPs electrode exhibited the enhanced sensing performances due to unique properties such as small peak potential separation, low electron transfer resistance, and large specific surface area.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.8
• /
• pp.542-548
• /
• 2014

Effects of bromide ($Br^-$) and iodide ($I^-$) concentrations, chlorine ($Cl_2$) doses, pH, temperature, ammonia nitrogen concentrations, reaction times and water characteristics on formation of iodinated trihalomethanes (I-THMs) during oxidation of iodide containing water with chlorine were investigated in this study. Results showed that the yields of I-THMs increased with the high bromide and iodide level during chlorination. The elevated pH significantly increased the yields of I-THMs during chlorination. The formation of I-THMs was higher at $20^{\circ}C$ than $4^{\circ}C$, $10^{\circ}C$ and $30^{\circ}C$. In chloramination study, addition of ammonium chloride ($NH_4Cl$) markedly increased the formation of I-THMs. Among the water samples collected from seven water sources including wastewater treatment plant (WWTP) effluent water (EfOM water), prepared humic containing water (HA water) and algal organic matter (AOM) containing water (AOM water), EfOM water generated the highest yields of I-THMs ($12.31{\mu}g/mg$ DOC), followed by HA water ($4.96{\mu}g/mg$ DOC), while AOM water produced the lowest yields of I-THMs ($0.99{\mu}g/mg$ DOC). $SUVA_{254}$ values of EfOM water, HA water and AOM water were $1.38L/mg{\cdot}m$, $4.96L/mg{\cdot}m$ and $0.97L/mg{\cdot}m$, respectively. The I-THMs yields had a low correlation with $SUVA_{254}$ values ($r^2$ = 0.002).