• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.32B no.10
• /
• pp.1280-1285
• /
• 1995

In this paper the optimized overlap driving scheme for improving the reduction problem of the operating voltage range occured by the overlap driving scheme proposed precedently and increasing the contrast ratio of screen image in the simple matrix LCDs is proposed. The characteristic estimation of the proposed method was performed in a condition that the number of scan electrodes was 120 and the threshold voltage of LC pixel was 2V and the overlap rate of scan signal was varied from 0% to 40% . As a result of estimation compared with the overlap driving scheme proposed precedently, this new method was certified as a method which it could increase the operating voltage range of the LC pixel by 16% in 20% overlap condition and it's operating voltage range was also increased very much with the increase of the overlap rate. Consequently this newly proposed method was certified as a method which it could maintain the improvement effect of the operating characteristics obtained by the overlap driving scheme proposed precedently with the big improvement in the contrast ratio of screen image.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.2C
• /
• pp.99-104
• /
• 2011

The chirp spread spectrum (CSS) technique spreads the data signal over a frequency bandwidth wider than minimum required bandwidth. By using time overlapping, the bit rate in CSS can be increased. However, for reliable transmission of data signal, the intersymbol interference (ISI) due to overlap should be analyzed. In this paper, the relation between the degree of overlap and ISI is analyzed in direct modulation binary phase shift keying CSS systems. In some cases, the overlap does not incur ISI at all and the ISI fluctuates or monotonically increases as the number of overlaps changes. It is also shown that the simulation results closely agree with the analytic results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.11
• /
• pp.1124-1131
• /
• 2014

The chirp spread spectrum (CSS) technique that transmits data signal by using a chirp signal is often used for maritime wireless communication systems such as sound detection radar systems for submarines. However, maritime multipath environment could reduce the data rate of the CSS system. To tackle the problem, an overlap-based CSS transmission scheme is proposed and analyzed in this paper: Based on the approximated Gaussian Q function, we derive a closed form expression of the bit error rate (BER) of the proposed overlap-based CSS system and investigate the mathematical relationship between the number of overlaps and the intersymbol interference (ISI).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.4C
• /
• pp.469-475
• /
• 2009

Overlap is one of the techniques for increasing bit rate in chirp spread spectrum (CSS). More overlaps can offer higher data throughput; however, they may cause more intersymbol interference (ISI) at the same time, resulting in serious bit error rate (BER) performance degradation. Thus, the number of overlaps should be decided according to the required BER performance. In this paper, we derive a closed form expression for BER of the overlap-based CSS system, exploiting the approximated Gaussian Q function. The derived BER expression includes the number of overlaps as a parameter, and thus, would be very useful in determining the number of overlaps for a specified BER. The numerical results demonstrate that the BER derived in a closed form closely agrees with the simulated BER.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.4
• /
• pp.33-39
• /
• 1997

The crystallization temperature of an amorphous silicon (a-Si) can be lowered down to 400.deg. C by a new method : Double-metal induced lateral crystallization (DMILC). The a-Si film was laterally crystallized from Ni and Pd deposited area, and its lateral crystallization rate reaches up to 0.2.mu.m/hour at that temperature and depends on the overlap length of Ni and Pd films; the shorter the overlap length, the faster the rate. Poly-Silicon thin film transistors (poly-Si TFT's) fabricated by DMILC at 400.deg. C show a field effect mobility of 38.5cm$^{3}$/Vs, a minimum leakage current of 1pA/.mu.m, and a slope of 1.4V/dec. The overlap length does not affect the characteristics of the poly-Si TFT's, but determines the lateral crystallization rate.

• Korea-Australia Rheology Journal
• /
• v.12 no.3_4
• /
• pp.175-179
• /
• 2000

Rheological properties of chitosan solutions were investigated as a function of polymer concentration. The viscosity curves for chitosan solutions consisted of two distinct viscosity regions, the Newtonian zero-shear viscosity (η$_{0}$) region and the shear rate dependent apparent viscosity (η$_{app}$) region. The shear rate dependence of viscosity was more clearly observed at higher chitosan concentrations. The critical coil overlap parameter (C＊〔η〕) was determined to be approximately 3.2 from a plot of zero-shear specific viscosity η$_{sp,0}$ vs coil overlap parameter (C〔η〕), which was lower than C〔η〕4.0 reported for other random coil polysaccharides. It was also found that the slope of η$_{sp,0}$ vs C〔η〕 was 3.9 at concentrated C〔η〕>C＊〔η〕domain, while 1.2 at dilute C〔η〕$_{0}$ ${\gamma}$/${\gamma}$$_{0.8}$ relation.ion.n.n.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.5
• /
• pp.129-133
• /
• 2007

Focused Ion Beam(FIB) systems is a useful tool for the fabrication of micro-nano scale structures. In this study, the effects of FIB etching on the Au microstructure are systematically investigated. As the fabrication parameters, ion dose, dwell time and beam overlap ratio are studied. First, the increases of Ga ion dose makes the milling yield higher and the sidewall of milling profile steeper. Dwell time is found to have little effects on the milling profile due to the relatively large milling area of $1\times1{\mu}m^2$ used in this study. However, beam overlap significantly affects not only milling rate but also milling profile. As the beam overlap ratio changes from positive to negative, the development of regular cross-stripe patterns at the bottom with low milling rate is observed.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.11
• /
• pp.17-23
• /
• 2010

Titanium alloy is one of the hard processing materials made by the traditional manufacturing method because of the excellent mechanical strength. Ablation of titanium alloy is investigated by using a femtosecond laser which is a regenerative amplified Ti:sapphire laser with 1kHz repetition rate, 184fs pulse duration time and 785nm wavelength. Experiments are carried out under various ablation conditions with different pulse overlap ratios for the rectangular shape and micro hole. Test results show that the ablation characteristic according to pulse overlap ratio of titanium alloy seems to be as non-linear type at the different zone of energy fluence. The optimal condition of rectangular shape processing is obtained at the laser peak power 1.3mW, pulse overlap ratio of 90%, beam gap of $1\;{\mu}m$. The micro hole has a good quality from the pulse overlap ratio of 99% at the same laser peak power. With the optimal processing condition, the fine rectangular shape and micro hole without burr and thermal damage are achieved.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.7
• /
• pp.110-116
• /
• 1994

In this paper a Duty Effective Overlap Scanning method (DEOS) for the improvement of driving efficiency of LC displays which have the RMS voltage responding characteristics is proposed and new processing method of data signals for optimum application of this method is also proposed. Proposed method has a few advantages such as the increment of duty ratio the increment of driving power loaded on LC cell and the decrement of RMS voltage error rate caused by signal attenuation on electrodes composing of display when compared with the conventional method which is called as optimum voltage amplitude selection method. And also by adopting new data signal processing method which has 3 kinds of voltage levels additional advantage much improving crosstalk phenomenon which is the most serious problems of simple matrix structured display is obtained. For the characteristic estimation new mathematical representation for new overlap scanning method and data signal processing method are induced and defined. And by the defined formula and simulation the characteristics of the proposed method and the conventional method are compared and analyzed. As a result of estimation this new method being able to optimize the overlap rate of scan signal and using 3 levels of data signals has the characteristic which can improve the driving efficiency of LC displays.

• Journal of Communications and Networks
• /
• v.1 no.3
• /
• pp.158-165
• /
• 1999

This paper studies interconnection of DCS1800 and GSM900 dual-band networks. Two types of interconnection config-urations for GSM services, non-overlap and overlap, are described. We propose analytic and simulation models to investigate the ben-efit of the overlap configuration. Our results explain how the radio channel capacities, the inter-system handoff failure rate, the origi-nating call traffic ratio and the offered loads affect the system per-formance. This study indicates that with appropriate overlap con-figuration, the GSM dual-band network can significantly improve the quality of cellular service.