• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.266-271
• /
• 2003

The numerical study was carried out to effectively cool Induction motor applied to a washing machine. The outer rotor made of steel periodically spins up and down. The stator consists of the thin layered iron plates and copper coil. The effective cooling system is necessary to solve the reliability problem caused by the electric losses at the coil and the iron plate. Because the heat transfer rate of the natural convection in partially open space is generally low, thus it is necessary to enhance the heat transfer using rotating perforated plate. The flow phenomena around the motor are very complex due to the motor geometry and the outer rotor motion. The mixed convection takes place due to the slow rotation speed. The three dimensional flow simulation was performed using rotating reference frame technique and Boussinesq approximation but the radiation effect was neglected. It was found that the angle and direction of the cooling blades play an important role in the stator temperature.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.463-468
• /
• 2011

According to a quantum leap of the performances of automobile, environmental factors are important as functional factors, especially noise. BLDC motor, one of the part of automobile, is also no exception. In this paper, investigation of the sound sources of outer rotor type BLDC motor is performed. In order to reduce noise, it must be necessary knowing sound source. To this end, this paper is analyzed two viewpoints, structural and electromagnetic causes. For structural analysis, modal experiment and 3D mode analysis are performed. On behalf of electromagnetic analysis, 2D finite element method is carried out. Finally, coupling analysis is performed in order to know about influence between two factors.

• Journal of the Korean Magnetics Society
• /
• v.25 no.6
• /
• pp.198-202
• /
• 2015

This s paper presents characteristics Analysis of Outer Rotor type BLDC Motor. To reduce the cogging torque and to make the high back EMF constant of the motor, Not only magnetization directions of a permanent magnet are investigated, but also a tooth chamfer of a stator is optimized. The design and analysis results are verified with experimental results.

• Journal of Drive and Control
• /
• v.11 no.4
• /
• pp.15-24
• /
• 2014

It is difficult to analytically derive a volumetric displacement formula for a gerotor hydraulic motor due to the complexity of the geometric shape of its gear lobes. This work proposes an analytical method for the volumetric displacement, a relatively easy method based upon two physical concepts: conservation between hydraulic energy and mechanical shaft energy, and torque equilibrium for the rotor's motion. The first research using these concepts was conducted on inner and outer rotors rotating with respect to each rotor axis. This work represents the second report conducted on an inner rotor revolving as a planetary motion on the stationary outer rotor. The formula equations regarding the volumetric displacement and flow rate are derived, and the proposed formula about the volumetric displacement is proven to be the same as another analytical displacement formula: the so-called vane length method. From the formula, volumetric displacement is calculated for an example geometry of the gear lobes. The resultant displacement is confirmed to be the same as the value calculated from the chamber volume method. The proposed analytical formula can be utilized in the analysis and design of gerotor hydraulic motors. Because it is based on torque equilibrium, this formula can provide a better understanding of torque performance, such as torque ripple, in designing a gerotor type motor.

• International Journal of Aeronautical and Space Sciences
• /
• v.12 no.2
• /
• pp.190-199
• /
• 2011

Unsteady flow simulations of complete helicopter configurations were conducted, and the flow fields and the aerodynamic interferences between the main rotor, fuselage, and tail rotor were investigated. For these simulations, a three-dimensional flow solver based on unstructured meshes was used, coupled with an overset mesh technique to handle relative motion among those components. To validate the flow solver, calculations were made for a UH-60A complete helicopter configuration at high-speed and low-speed forward flight conditions, and the unsteady airloads on the main rotor blade were compared to available flight test data and other calculated results. The results showed that the fuselage changed the rotor inflow distribution in the main rotor blade airloads. Such unsteady vibratory airloads were produced on the fuselage, which were nearly in-phase with the blade passage over the fuselage. The flow solver was then applied to the simulation of a generic complete helicopter configuration at various flight conditions, and the results were compared with those of the CAMRAD-II comprehensive analysis code. It was found that the main rotor blades strongly interact with a pair of disk-vortices at the outer edge of the rotor disk plane, which leads to high pulse airloads on the blade, and these airloads behave differently depending on the specific flight condition.

• Progress in Superconductivity and Cryogenics
• /
• v.2 no.2
• /
• pp.44-48
• /
• 2000

The high temperature superconducting bulk can be used as the rotor of an ac motor. This paper presents the fabrication and test results of a ac motor with HTS bulk rotor. The rotor of a conventional squirrel cage induction motor was replaced with cylinder type YBCO bulk. Height and outer diameter of the HTS bulk was 15mm and 46mm, respectively. Eddy current brake using aluminium disk was used to measure the torque of the HTS motor. No load test, locked rotor test and load test were performed to examine the characteristics of the HTS motor. Test results show the motor can rotate at synchronous speed without any special starting circuit. Maximum output power of the constructed HTS motor was 408W.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.17 no.4
• /
• pp.48-54
• /
• 2009

We implemented the Aural Cueing System(ACS) system of the reconfigurable tactical trainer(RTT) for th rotor aircraft. RTT provides a collective training system to meet aviation training requirements and supports organizational training for aviations units in combined arms collective training and mission rehearsal. ACS handles the volume, pitch and repetition of the digitally stored sounds based on commands it receives from an UDP/IP. In this paper, we explained and implemented the conceptual and detail design the ACS system for the rotor aircraft such as AH-1H(Iroquios), UH-60(Blackhwak), AH-1(Cobra) etc. The conceptual design composed of the sound cueing data analysis, sound modelling which is inner, outer, weapon and warn environment of rotor aircraft, sound synthesis and replay.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.267-268
• /
• 2006

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.573-576
• /
• 2002

A flow characteristics of automotive oil pump of gerotor type has been investigated numerically. For the simulation of gerotor that have different rotating velocity at inner rotor and outer rotor, node expansion and contraction method was adopted. ASI (Arbitrary Sliding Interfaces) method was also applied at interface between rotating gerotor and stationary volute. The present results showed good agreement with the experimental data.

• Tribology and Lubricants
• /
• v.15 no.2
• /
• pp.164-170
• /
• 1999

Gerotor is widely used as a hydraulic pump or motor, by virtue of its volume changing ability. Performance deterioration of a gerotor hydraulic motor mainly due to the wear come from the contact between inner rotor with trochoidal curve and outer rotor with circular arc profile. This research covers the basic investigation about the contact forces of a gerotor hydraulic motor using analytic method. The influence of the eccentricity and the radius of circular arc teeth on the contact stress was evaluated.