• Journal of Biomedical Engineering Research
• /
• v.10 no.3
• /
• pp.261-268
• /
• 1989

The characteristics of aging of near-equiatomic Ni-Ti alloy has been studied by the three point bend test and the measurement of Differential Scanning Calorimetry(DSC). The DSC is used to measure precise transformation temperatures and the amount of thermal energy required for the corresponding phase transformation. The effort of hardness on aging treatment in saline solution of $37^{\circ}C$ was higher for the annealed than solution treated specimens. As the testing temperature inc- rease from under $M_f$ to above $A_f$ temperature, the elastic stiffness increased. Almost full recovery can be achieved after bending below Belo outer fiber strain. Total bend recovery decreased gradually as aging time and bend angle is increased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.586-588
• /
• 2001

Inner part of FRP specimen was made unidirectionally by pultrusion method and outer part of FRP was made by filament winding method to study the effect of fiber orientatons on the strength of FRP. The strength of bending and compression was simulated and evaluated. The results of simulated strength and evaluated strength were different greately each other. The stress which affect the feature of FRP was simulated to investigate the difference of the results between simulation and evaluation Shear stresses were investigated to the main stress to affect the fracture of FRP.

• Journal of Welding and Joining
• /
• v.23 no.3
• /
• pp.34-39
• /
• 2005

It is required for the steel materials used in the sour environment to have sufficient resistance to hydrogen induced cracking(HIC). For line pipe steels, HIC resistance could be varied during pipe making process due to the large plastic deformation applied in the thick-wall pipe. In order to figure out such effect, HIC tests were performed not only in the plate condition but in the pipe condition and their results were compared in terms of cracking ratio. Test results demonstrated a detrimental effect of plastic deformation to HIC resulting in a substantial increase in the cracking ratio after pipe forming process. All of the cracks found in the pipe material were located in the outer layer of pipe where the tensile strain was resulted during pipe forming stage. In order to understand the HIC resistance of the pipe but in the plate condition, it was suggested to pre-strain the plate to some extent before the HIC test.

• Journal of Advanced Marine Engineering and Technology
• /
• v.12 no.3
• /
• pp.29-42
• /
• 1988

With the Hertzian contact theory, it is possible to determine the bearing load distributing pattern among the balls and rollers and also variations of the load-displacement relationships for rolling elements contacting raceways according to bearing clearance, load distribution, contact forces and dimensions of bearing components (i.e diameter of raceway and rolling elements), etc. In this paper the calculation theories of contact load and normal approach between two raceways under radial load are reviewed, and compared these calculation results with those of experimental results. A new calculation theory for elastic displacement of outer-race of ball bearing under radial load is developed by authors by application of energy method, which is independent on the effects of roughness, bending or eccentricity of bearing with driving shaft, and is effective in measuring the location of its defect.

• Korean Journal of Optics and Photonics
• /
• v.13 no.6
• /
• pp.473-478
• /
• 2002

Circular slab waveguides are conformally mapped into straight waveguides. In the outer cladding region with monotonically increasing index profile, modified Airy functions (MAF) of traveling-wave form are introduced to express the leaky mode. Field distributions and losses calculated by the proposed method are compared with those obtained by the WKB (Wentzel-Kramers-Brillouin) method. Detailed numerical examples are presented and compared with the conventional WKB methods, demonstrating our method not only allows a converging field at turning points but also guarantees fine accuracy.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.1
• /
• pp.99-104
• /
• 1998

It is a good flexibility of bending body and non-interaction of outer bodies for slit antenna to be being studied and developed in this paper. The characteristics of leaked EM waves in slit transmission line are applied to antennas of tele-communication systems. The computer simulations using a special software adapt to design a new slit antenna, and to apply to tele-communications systems with frequencies of land mobile communication (800-900MHz). The good results of which reflection coefficient 511 is 0.21 and directivity is 2.9 and band-widths are 1.5MHz in 851MHz are shown.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1530-1532
• /
• 2000

The properties of FRP usually depends on the fabricating method. The fiber orientation of FRP is also depends on the fabricating method. The fiber orientation in FRP has a great effect on the strength of FRP because the strength of FRP mainly depends on the strength of fiber. In this study. compressive and bending strength of FRP rods were investigated. Inner part of FRP was made unidirectionally by pultrusion method and outer part of FRP was made by wrapping method. The size effect was also investigated with pultruded FRP rods.

• Journal of Ocean Engineering and Technology
• /
• v.20 no.3 s.70
• /
• pp.24-36
• /
• 2006

This paper investigates wave loads of ships that suffer sinkage due to flood in a compartment caused by damage on the side of the hull. By analyzing ships with various sizesof damage opening, the influence of opening size on ship response is investigated. The motion of the damaged ship is analyzed by using the boundary element method, based on three-dimensional potential theory, considering hydrodynamic pressure in the flooded compartments. The shear forces, bending moments and torsional moments are calculated by the direct integration of the three dimensional hydrodynamic pressure on the outer and inner hulls. A RORO passenger ship with length of 174.8 m is considered in the numerical example, and results for wave loads are discussed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.493-496
• /
• 2008

The residual stress generated in the boron steel blank formed via hot press forming process was predicted by JMatPro, a material property modeler, and Abaqus. The numerical predictions were compared by the experimental measurements obtained by the instrumented indentation. Both the predicted and measured principal stresses monitored at the outer surface of central bending position were qualitatively in good agreement. It was concluded that the residual stresses generated from hot forming process is not negligible as it has been generally assumed, although the spring back deformation is quite small. This should be specially considered from the part design stage since the tensile nature of the residual stress exhibited on the surface may lead to the stress corrosion cracking.

• Journal of Urban Science
• /
• v.10 no.1
• /
• pp.11-20
• /
• 2021

In this study, the vibration characteristics were theoretically analyzed by modeling a free isotropic rotating disk with an outer periphery with a fixed inner periphery, paying attention to disks used as storage devices for information devices, especially magnetic disks, magneto-optical disks, and compact disks in which the head and disk are non-contact. Iluminate with Composite materials represented by fiber-reinforced plastics (FRP) have high specific strength (strength/density) and specific stiffness (narrowness/density). It is used in the elements, and its use is rapidly expanding. Under this circumstance, the disk currently manufactured using an isotropic material made of various plastic materials such as aluminum or polycarbonate as a base material is an extremely anisotropic material made of a composite material, and the circumferential stiffness of the disk is made of reinforcing fibers in the circumferential direction. It is modeled as an anisotropic rotating disk with increased, and its influence on the vibration characteristics is revealed.