• Structural Engineering and Mechanics
• /
• 제8권3호
• /
• pp.257-272
• /
• 1999

In this paper a simple finite element is proposed for analyzing out of plane vibration of thin walled curved beams, with both open and closed sections, considering shear flexibility. The present element is obtained from a variational formulation governing the dynamics of a three-dimensional elastic body in which the stress tensor as well as the displacements are variationally independent. The element has two nodes with four degrees of freedom in each. Numerical examples for the first six frequencies are performed in order to assess the accuracy of the finite element formulation and to show the influence of the shear flexibility on the dynamics of the member.

• Journal of Welding and Joining
• /
• 제17권2호
• /
• pp.66-75
• /
• 1999

Weld bead quality in tailored blank(TB) is critically affected by edge preparation of sheets. The edge quality of prepared sheets for TB can be classified into straightness and the cross section quality of sheared plane such as a ratio of shear face, shear plane angle, etc. In order to have a good edg quality for butt-welding sheets, precision shearing will be recommended. In this paper, the feasibility of a conventional mechanical shearing as the edge preparation for tailored blanks is studyied. It reveals that fine shearing may not be the unique solution as it is generally accepted. To obtain the good shearing condition with a conventional mechanical shearing, experiments were carried out using Tahuchi method. The major parameters affecting a sheared contour are the clearance between upper blade and lower blade, and shear angle. The optimal shearing condition yields a very good straightness along the entire length of the cut, which gives a butt joint gap less than 10% of the base material thickness. The good cross section of sheared plane is also achieved in the optimal shearing condition such as a ratio of the shear face above 65%, a cross section's shear plane angle above 85%, little burr, which is providing finally good weld beads.

• Structural Engineering and Mechanics
• /
• 제78권3호
• /
• pp.269-280
• /
• 2021

Reinforced concrete (RC) structural walls with L-shaped sections are commonly used in RC buildings. The walls are often expected to sustain biaxial load and Unsymmetrical bending in an earthquake event. However, there currently exists limited experimental evidence regarding their seismic behaviour in these lateral loading directions. This paper makes experimental and numerical investigations to these walls behaviours. Experimental evidences are presented for four L-shaped wall specimens which were tested under simulated seismic load from different lateral directions. The results highlighted some distinct behaviour of L-shaped walls sustaining Unsymmetrical bending relating to their seismic performance. First, due to the Unsymmetrical bending, out-of-plane reaction forces occur for these walls, which contribute to accumulation of the out-of-plane deformations of the wall, especially when out-of-plane stiffness of the section is reduced by horizontal cracks in the cyclic load. Secondly, cracking was found to affect shear centre of the specimens loaded in the Unsymmetrical bending direction. The shear centre of these specimens distinctly differs in the flange in the positive and negative loading direction. Cracking of the flange also causes significant warping in the bottom part of the wall, which eventually lead to out-of-plane buckling failure.

• Steel and Composite Structures
• /
• 제38권4호
• /
• pp.463-476
• /
• 2021

The concept of using Steel-concrete (SC) composite walls as retaining walls has recently been introduced by the authors and their effectiveness of resisting out-of-plane loads has also been demonstrated. In this paper, an improved analytical formulation based on partial interaction theory, which has previously been developed by the authors, is presented. The improved formulation considers a new loading condition and also accounts for cracking in concrete to simulate the real conditions. Due to a limited number of test specimens, further finite element (FE)simulations are performed in order to verify the analytical procedure in more detail. It is observed that the results from the improved analytical procedure are in excellent agreement with both experimental and numerical results. Moreover, a detailed parametric study is conducted using the developed FE model to investigate effects of different parameters, such as distance between shear connectors, shear connector length, concrete strength, steel plate thickness, concrete cover thickness, wall's width to thickness ratio, and wall's height to thickness ratio, on the behavior of SC composite walls subjected to out-of-plane loads.

• 한국전산구조공학회논문집
• /
• 제20권4호
• /
• pp.417-425
• /
• 2007

곡선보(curved beam)의 회전관성(rotatory inertia) 및 전단변형(shear deformation)을 고려한 면외(out-of-plane) 자유진동을 해석하는데 미분구적법(DQM)을 이용하여 고정-고정 경계조건(boundary conditions)과 다양한 굽힘각(opening angles)에 따른 진동수(frequencies)를 계산하였다. DQM의 결과는 엄밀해(efact solution) 또는 다른 수치해석 결과와 비교하였으며, DQM은 적은 요소(grid points)를 사용하여 정확한 해석결과를 보여주었다.

• 대한조선학회논문집
• /
• 제55권6호
• /
• pp.521-526
• /
• 2018

The doubler plate design system for the reinforcement of the ship plate members was developed considering various loads that subjected to the in-plane biaxial load, the in-plane shear load and out-of-plane load. The author summarized the accuracy of the development formula and equations through the equivalent plate thickness concept and finally introduced the new design system of doubler plate reinforcement. Through this study, it can be considered as an initial design guideline based on ship doubler plate reinforcement strength at areas without repeated load, or an initial structure analysis model for final structural design.

• International journal of advanced smart convergence
• /
• 제13권2호
• /
• pp.103-109
• /
• 2024

A nonlinear numerical analysis of orientation and velocity fields of the full Ericksen-Leslie theory for a nematic liquid crystal under shear flow is given. We obtained for the first time the three-dimensional orientation and two component velocity profiles evolutions for both in- and out-of-shear plane orientation anchorings. Complex evolution routes to steady state were found even for shear aligning nematic. As the Ericksen number increases monotonic evolution of velocity and orientation shifts towards multi-region nucleating director rotation growth with complex secondary flow generations. We found that contrary to the in-shear-plane anchorings like homeotropic or parallel anchorings, binormal anchoring gives rise to substantial non-planar three-dimensional orientation with nonzero secondary flow.

• International Journal of Aerospace System Engineering
• /
• 제3권1호
• /
• pp.10-16
• /
• 2016

A trigonometric Layerwise higher order shear deformation theory (TLHSDT) is developed and implemented for free vibration and buckling analysis of laminated composite and sandwich plates by analytical and finite element formulation. The present model assumes parabolic variation of out-plane stresses through the depth of the plate and also accomplish the zero transverse shear stresses over the surface of the plate. Thus a need of shear correction factor is obviated. The present zigzag model able to meet the transverse shear stress continuity and zigzag form of in-plane displacement continuity at the plate interfaces. Hence, botheration of shear correction coefficient is neglected. In the case of analytical method, the governing differential equation and boundary conditions are obtained from the principle of virtual work. For the finite element formulation, an efficient eight noded $C^0$ continuous isoparametric serendipity element is established and employed to examine the dynamic analysis. Like FSDT, the considered mathematical model possesses similar number of variables and which decides the present models computationally more effective. Several numerical predictions are carried out and results are compared with those of other existing numerical approaches.

• Structural Engineering and Mechanics
• /
• 제13권5호
• /
• pp.491-504
• /
• 2002

Recently we formulated a 2D hybrid stress element from the 3D Hellinger-Reissner principle for the analysis of thick bodies that are symmetric to the thickness direction. Polynomials have typically been used for all the displacement and stress fields. Although the element predicted the dominant stress and all displacement fields accurately, its prediction of the out-of-plane shear stresses was affected by the very high order terms used in the polynomials. This paper describes an improved formulation of the 2D element using Fourier series expansion for the out-of-plane displacement and stress fields. Numerical results illustrate that its predictions have markedly improved.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.65-68
• /
• 2008

구조실험에서 실험장치의 구성방법은 실험 결과에 결정적인 영향을 미치는 중요한 요소이다. 가력 장치와 치구를 어떻게 구성하느냐에 따라서 의도하는 실험조건이 구현될 수 있다. 특히, 실물구조물과 같은 대형 실험체를 이용하여 실험하는 경우에는 실험장치를 구성하는 경제적 비용을 감안하여 정확한 하중을 가력하기 위한 실험장치의 구성이 더욱 중요하다. 본 논문은 이와 같은 필요성에 의하여 구조실험시설에서 일반적으로 이용하고 있는 설비를 이용하여 경제적이고 효과적인 실험장치를 구성하여 대형 보형실험체의 실험을 수행하고 그 결과를 기술하기 위하여 작성되었다.