• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.396-396
• /
• 2009

Chalcopyrite semiconductor $CuInSe_2$ nanoparticles were prepared using a low temperature colloidal route by reacting the starting materials (CuI, $InI_3$ and $Na_2Se$) in solvents. After synthesised $CuInSe_2$ nanoparticles precursors were mixed with organic binder for the viscosity of the precursor slurry to be suitable for the doctor blade method. The mixture of $CuInSe_2$ and binder was deposited onto molybdenum-coated sodalime glass substrates to form thin film. The precursor thin films were preheated on the hot plate to remove remaining solvents and binder material. After subsequent thermal processing of the thin film under a selenium ambient, $CuInSe_2$ absorber layer with grain size significantly lager than that of the nanoparticles was formed.

• 한국레이저가공학회지
• /
• 제13권1호
• /
• pp.11-15
• /
• 2010

Indium tin oxide (ITO) provides high electrical conductivity and transparency in the visible and near IR (infrared) wavelengths. Thus, it is widely used as a transparent electrode for the fabrication of liquid crystal displays (LCDs) and organic light emitting diode displays (OLRDs), photovoltaic devices, and other optical applications. Lasers have been used for removing coating on polymer substrate for flexible display and electronic industry. In selective removal of ITO layer, laser wavelength, pulse energy, scan speed, and the repetition rate of pulses determine conditions, which are efficient for removal of ITO coating without affecting properties of the polymer substrate. ITO coating removal with a laser is more environmentally friendly than other conventional etching methods. In this paper, pattering of ITO film from polymer substrates is described. The Yb:KGW femtosecond laser processing system with a pulse duration of 250fs, a wavelength of 1030nm and a repetition rate of 100kHz was used for removing ITO coating in air. We can remove the ITO coating using a scanner system with various pulse energies and scan speeds. We observed that the amount of debris is minimal through an optical and a confocal microscope, and femtosecond laser pulses with 1030nm wavelength are effective to remove ITO coating without the polymer substrate ablation.

• 한국초전도ㆍ저온공학회논문지
• /
• 제4권2호
• /
• pp.5-10
• /
• 2002

Deposition condition of NiO that is one of Possible buffer layers for YBCO coated conductors was studied. NiO was deposited on textured Ni substrates by a MOCVD (metal-organic chemical vapor deposition) method. The degree of texture, and the surface roughness were analyzed by X-ray Pole figure, atomic force microscope and scanning electron microscope. The (111) and (200) textures were competitively developed , depending on an oxygen partial Pressure(PO2) and deposition temperature (Tp). The (200) textured NiO layer was deposited at Tp=450~47$0^{\circ}C$ and PO2= 1.67 Torr Out-of-Plane ($\omega$-scan) and in-plane ($\Phi$-scan) textures of the (200) NiO films were as good as 10.34$^{\circ}$ and 10.00$^{\circ}$ respectively The AFM surface roughness of NiO was in the range of 3~4.5 nm at PO2=0.91~3.34 Torr and at Tp=47$0^{\circ}C$ , and in the range of 3~13 nm at TP=450~53$0^{\circ}C$ and at PO2=1.67 Torr.

• Korean Chemical Engineering Research
• /
• 제55권6호
• /
• pp.754-761
• /
• 2017

알코올에 분산된 콜로이드 실리카를 아크릴 단량체인 pentaerythritol triacrylate (PETA)와 혼합시킴에 의해 UV 경화형 친수성 코팅 용액을 제조하였다. 또한 이 친수성 코팅 용액을 PC 기재 위에 스핀코팅 시킨 후 10 min 동안 UV 경화시킴에 의해 친수성 코팅 도막이 제조되었다. 이 과정 중 코팅 용액 중의 콜로이드 실리카 양을 10~50 g으로 변화시켜 코팅 도막의 친수성에 미치는 영향을 살펴보았다. 그 결과 코팅 용액 중의 콜로이드 실리카 양은 코팅 도막의 친수성에 큰 영향을 미치며, 콜로이드 실리카 양이 30 g인 경우에 $37^{\circ}$의 가장 낮은 접촉각과 H의 우수한 연필경도를 나타내었다.

• 한국세라믹학회지
• /
• 제42권4호
• /
• pp.219-223
• /
• 2005

A promising capacitor, which has conformable step coverage and good uniformity of thickness and composition, is needed to manufacture high-density non-volatile FeRAM capacitors with a stacked cell structure. In this study, ferroelectric $Bi_{3.61}Nd_{0.39}Ti_3O_{12}$ (BNdT) thin films were prepared on $Pt(111)/TiO_2/SiO_2/Si$ substrates by the liquid delivery system MOCVD method. In these experiments, $Bi(ph)_{3}$, $Nd(TMHD)\_{3}$ and $Ti(O^iPr)_{2}(TMHD)_{2}$ were used as the precursors and were dissolved in n-butyl acetate. The BNdT thin films were deposited at a substrate temperature and reactor pressure of approximately $600^{\circ}C$ and 4.8 Torr, respectively. The microstructure of the layered perovskite phase was observed by XRD and SEM. The remanent polarization value (2Pr) of the BNdT thin film was $31.67\;{\mu}C/cm^{2}$ at an applied voltage of 5 V.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 영호남 학술대회 논문집
• /
• pp.31-34
• /
• 2003

($Ba_{0.6-x}Sr_{0.4}Ca_x)TiO_3$ (BSCT) (x=0.10, 0.15, 0.20) powder, prepared by the sol-gel method, were mixed with organic vehicle and the BSCT thick films were fabricated by the screen-printing techniques on alumina substrates using the BSCT paste. The structural and the electrical properties were investigated for various composition ratio and sintering temperature. BSCT thick film thickness, obtained by four printings, was approximately 110 ~ 120 ${\mu}m$. The Curie temperature and dielectric constant at room temperature were decreased with increasing Ca content. The relative dielectric constant, dielectric loss and tunability of the BSCT(50/40/10) specimen, which was sintered at $1420^{\circ}C$ and measured at 1MHz, were about 910, 0.46% and 9.28% at 5kV/cm, respectively.

• Transactions on Electrical and Electronic Materials
• /
• 제11권2호
• /
• pp.49-53
• /
• 2010

Microstructural origins of leakage current and physical degradation during operation in product-quality AlGaN/GaN high electron mobility transistor (HEMT) devices were investigated using photon emission microscopy (PEM) and transmission electron microscopy (TEM). AlGaN/GaN HEMTs were fabricated with metal organic chemical vapor deposition on semi-insulating SiC substrates. Photon emission irregularity, which is indicative of gate leakage current, was measured by PEM. Site specific TEM analysis assisted by a focused ion beam revealed the presence of threading dislocations in the channel below the gate at the position showing strong photon emissions. Observation of electrically degraded devices after life tests revealed crack/pit shaped defects next to the drain in the top AlGaN layer. The morphology of the defects was three-dimensionally investigated via electron tomography.

• Mycobiology
• /
• 제41권4호
• /
• pp.210-213
• /
• 2013

The objectives of this study were to evaluate applicability of food waste compost (FWC) as a substrate for cultivation of Ganoderma lucidum, Lentinula edodes, and Pholiota adipose, and to determine contents of Ca, Mg, Na, and K in fruiting bodies (FB). FB yield per substrate in FWC-free controls was $53{\pm}4g/kg$ for G. lucidum, $270{\pm}90g/kg$ for L. edodes, and $1,430{\pm}355g/kg$ for P. adipose. Substrates supplemented with FWC showed the highest FB production at FWC content of 10% for G. lucidum ($64{\pm}6g/kg$), and 13% for L. edodes ($665{\pm}110g/kg$) and P. adipose ($2,345{\pm}395g/kg$), which were 1.2~2.5 times higher than the values for the controls. P. adipose contained higher amounts of mineral elements than the other species. Ca, Mg, Na, and K content in FB did not show a significant relation to FWC content.

• Current Photovoltaic Research
• /
• 제5권4호
• /
• pp.140-144
• /
• 2017

$CuSbS_2$ (CAS) and $CuSbSe_2$ (CASe) nanocrystals (NCs), which consist of earth-abundant elements, were synthesized by a mechanochemical method. Elemental precursors such as copper, antimony, sulfur, and selenium were used without adding any organic solvents or additives. The NCs were synthesized by milling for a few hours. The sudden phase changes occurred by self-ignition and propagation, as previously observed in other mechanochemical synthetic processes. The XRD, Raman, and TEM analysis were carried out to determine the crystallinity and secondary phase of the as-synthesized CAS and CASe NCs, confirming the phase-pure synthesis of CAS and CASe. Optical properties were investigated by UV-Vis spectroscopy and it was observed that the band gap energies were about 1.1 and 1.5 eV, respectively for CAS and CASe, suggesting the potential for the use as solar cell materials. The NC colloids dispersed in anhydrous ethanol were prepared and coated on Mo substrates by a facile doctor-blade method. The investigation on the solar cell properties of the as-synthesized materials is underway.

• 한국세라믹학회지
• /
• 제53권6호
• /
• pp.622-627
• /
• 2016

The effects of the debinding atmosphere on the properties of sintered reaction-bonded $Si_3N_4$ (SRBSN) ceramics prepared by tape casting method were investigated. Si green tape was produced from Si slurry of Si powder, using 11.5 wt% polyvinyl butyral as the organic binder and 35 wt% dioctyl phthalate as the plasticizer. The debinding process was conducted in air and $N_2$ atmospheres at $400^{\circ}C$ for 4 h. The nitridation process of the debinded Si specimens was performed at $1450^{\circ}C$, followed by sintering at $1850^{\circ}C$ and 20 MPa. The results revealed that the debinding atmosphere had a significant effect on $Si_3N_4$ densification and thermal conductivity. Owing to the higher sintered density and larger grain size, the thermal conductivity of $Si_3N_4$ specimens debinded in air was higher than that of the samples debinded in $N_2$. Thus, debinding in air could be suitable for the manufacture of high-performance SRBSN substrates by tape casting.