• 한국표면공학회지
• /
• 제47권3호
• /
• pp.104-108
• /
• 2014

To improve emission efficiency of organic light emitting devices (OLEDs), we fabricated the tandem OLED of ITO / 2-TNATA / NPB / SH-1: 3 vol.% BD-2 / Bphen / Liq / Al / $MoO_x$ (X nm) / 2-TNATA / NPB / SH-1: 3 vol.% BD-2 / Bphen / Liq / Al structure. And emission properties of single OLED and tandem OLED with $MoO_x$ thickness as charge generation layer (CGL) were measured. The current emission efficiency and quantum efficiency of tandem OLED with $MoO_x$ of 3 nm thickness were improved compare with single OLED from 7.46 cd/A and 5.39% to 22.57 cd/A and 11.76%, respectively. In case of thicker or thinner than $MoO_x$ of 3~5 nm, the current emission efficiency and quantum efficiency were decreased, because balance of electron and hole in emission layer was not matching. The driving voltage was increased from 8 V of single OLED to 15 V of tandem OLED by thickness increase of OLED. As a result, it was possible to improve the emission efficiency of OLEDs by optimized $MoO_x$ thickness.

• Journal of Electrochemical Science and Technology
• /
• 제8권2호
• /
• pp.96-100
• /
• 2017

Iridium(III) bis(2-phenylpyridinato-$N,C^{2^{\prime}}$)acetylacetonate ($(ppy)_2Ir(acac)$), a green dopant used in organic light-emitting devices (OLEDs), was subjected to electrochemical characterization to estimate its formal oxidation potential ($E^{o^{\prime}}$), HOMO energy level ($E_{HOMO}$), electron transfer rate constant ($k^{o^{\prime}}$), and diffusion coefficient ($D_o$). The employed combination of voltammetric methods, i.e., cyclic voltammetry (CV), chronocoulometry (CC), and the Nicholson method, provided meaningful insights into the electron transfer kinetics of $(ppy)_2Ir(acac)$, allowing the determination of $k^{o^{\prime}}$ and $D_o$. The quasi-reversible oxidation of $(ppy)_2Ir(acac)$ furnished information on $E^{o^{\prime}}$ and $E_{HOMO}$, allowing the latter parameter to be easily estimated by electrochemical methods without relying on expensive and complex ultraviolet photoemission spectroscopic (UPS) measurements.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.425-425
• /
• 2008

The transparent conducting oxides(TCOs) are widely used as electrodes for most flat panel display devices(FPDs), electrodes in solar cells and organic light emitting diodes(OLED). Among them, indium oxide materials are mostly used due to its high electrical conductivity and a high transmittance in the visible spectrum. The present study reports on a study of the electrical and optical properties of IGZO thin films prepared on glass and PET substrates by the combinational magnetron sputtering. We use the targets of IZO and Ga2O3 for the deposition process. In some case the deposition process is coupled with the End-Hall ion-beam treatment onto the substrates before the sputtering. In addition we control the deposition rate to optimize the film quality and to minimize the surface roughness. Then we investigate the effects of the Ar gas pressure and RF power during the sputtering process upon the electrical, optical and morphological properties of thin films. The properties of prepared IGZO thin films have been analyzed by using the XRD, AFM, a-step, 4-point probe, and UV spectrophotometer.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.382-384
• /
• 2009

In this study, high stable oxide thin-film transistors (TFTs) have been developed by using several approaching techniques, which including a change of the channel composition ratio in multi-component oxide semiconductors, a change of TFT structure with interfacial dielectric layers, a control of interface roughness, a channel-doping method, and so on.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.1014-1018
• /
• 2007

We have demonstrated the enhancement of the power efficiency and device lifetime of organic light-emitting diodes (OLEDs) by introducing the ETL 1 / ETL2 (composite ETL) structure between EML and cathode and the HIL1 (composite HIL) / HIL2 between anode and HTL. Compared to reference devices retaining conventional architecture, novel OLED structure shows an outstanding EL efficiency that is 1.6 times higher (${\sim}4.5$ lm/w versus ${\sim}$ 2.71 lm/w for the reference device) and lower driving voltage $({\bigtriangleup}V>1V)$, but also a longer lifetime and smaller operating voltage drift over time. It is suggested in this work that the device performance can be improved by in-situ ohmic contact through novel electron controlled structure and reduction of charge accumulation in the interface through composite HIL

• Bulletin of the Korean Chemical Society
• /
• 제34권8호
• /
• pp.2267-2270
• /
• 2013

A series of blue fluorescent emitters based on triphenylene derivatives were synthesized via the Diels-Alder reaction in moderate yields. The electronic absorption and emission characteristics of the new functional materials were affected by the nature of the substituent on the triphenylene nucleus. Multilayered OLEDs were fabricated with a device structure of: ITO/NPB (50 nm)/EML (30 nm)/Bphen (30 nm)/Liq (2.0 nm)/Al (100 nm). All devices showed efficient blue emissions. Among those, a device using 1 gives the best performances with a high brightness (978 cd $m^{-2}$ at 8.0 V) and high efficiencies (a luminous efficiency of 0.80 cd/A, a power efficiency of 0.34 lm/W and an external quantum efficiency of 0.73% at 20 $mA/cm^2$). The peak wavelength of the electroluminescence was 455 nm with CIEx,y coordinates of (0.17, 0.14) at 8.0 V.

• 반도체디스플레이기술학회지
• /
• 제8권1호
• /
• pp.33-38
• /
• 2009

We have investigated the effect of the ambient gases on the characteristics of AZO thin films for the OLED (organic light emitting diodes) devices. These AZO thin films are deposited by rf-magnetron sputtering under different ambient gases (Ar, Ar+$O_2$, and Ar+$H_2$) at 300. In order to investigate the influences of the oxygen and hydrogen, the flow rate of oxygen and hydrogen in argon mixing gas has been changed from 0.2sccm to 1sccm and from 0.5sccm to 5sccm, respectively. The AZO thin films were preferred oriented to (002) direction regardless of ambient gases. The electrical resistivity of AZO film increased with increasing flow rate of $O_2$ under Ar+$O_2$ while under Ar+$H_2$ atmosphere the electrical resistivity showed minimum value near 1sccm of $H_2$. All the films showed the average transmittance over 80% in the visible range. The OLED device was fabricated with different AZO substrates made by configuration of AZO/$\acute{a}$-NPD/DPVB/$Alq_3$/LiF/Al to elucidate the performance of AZO substrate.

• 한국표면공학회지
• /
• 제52권6호
• /
• pp.334-341
• /
• 2019

Organometal halide perovskite materials have attracted much attention in the photovoltaic and light emitting devices due to the compositional flexibility with AMX₃ formula (A is an organic amine cation; M is a metal ion; X is a halogen atom). The addition of homovalent or heterovalent metal cations to the bulk organohalide perovskites has been performed to modify their energy band structure and the relevant optoelectronic properties by ligand-assisted ball milling. Here, we report CH₃NH₃Pb_1-xM_xBr₃ nanocrystals substituted by metallic cations (M is Sn²⁺, In³⁺, Bi³⁺; x = 0, 0.01, 0.02, 0.05, 0.1, 0.2). Photoluminescence and quantum yield was significantly reduced with increasing metallic cations content. These quenching effect could be resulted from the metal cations that behave as a non-radiative recombination center.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 학술대회 및 기술세미나 논문집 디스플레이 광소자
• /
• pp.54-55
• /
• 2006

Organic light-emitting diodes(OLEOs) are attractive because of possible application in display with low operating voltage, low power consumption, self-emission and capability of multicolor emission by the selection of emissive material. We investigated the effects of deposition rate on the electrical characteristics, physical characteristics and optical characteristics of OLEOs in the ITO(indium-tin-oxide)/N.N'-diphenyl-N,N'-bis(3-methyphenyl)-1,1'-biphenyl-4,4'-diamine(TPD)/tris(8-hydroxyquinoline)aluminum($Alq_3$)/Al device. We measured current density, luminous flux and luminance characteristics of devices with varying deposition rates of TPD and $Alq_3$. It has been found that optimal deposition rate of TPD and $Alq_3$ were respectively $1.5{\AA}/s$ from the device structure. An AFM measurement results, surface roughness of the deposited film was the lowest when deposition rate was $1.5{\AA}/s$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.428-429
• /
• 2006

In this thesis, verifies electrical-optical characteristics of phosphorescent materials. basic structure of fabricating devices is glass/ITO/$\alpha$-NPD($300{\AA}$)/CBP:Guest($300{\AA}$)/BCP($80{\AA}$)/$Alq_3(100{\AA})$/Al($1000{\AA}$). In efficiency, fabrication of organic light emitting diodes using $Ir(btp)_2acac$ phosphorescent material is external quantum efficiency 0.268% as doping concentration 3%. At CIE coordinates, phosphorescent material $Ir(btp)_2acac$ following materials moves high purity red color(x=0.6686, y=0.3243). The brightness shows $285cd/cm^2$.