• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2018년도 전력전자학술대회
• /
• pp.63-65
• /
• 2018

This paper presents a DTC-PWM(Direct Torque Control-Pluse Width Modulation) method of PMSM(Permanent Magnet Synchronous Motor) using the flux-torque hysteresis band. In order to keep the flux and torque error of the PMSM within the hysteresis band, the optimal PWM duty ratio is calculated by the error of the flux and torque with the flux and torque vector of the selected voltage vector. According to the flux duty ratios and the torque duty ratios, the optimized duty ratio to reduce the errors is selected by the calculated duty ratios. In the proposed method, the selected voltage vector is divided into d-q axis components with a simple method. And the flux duty ratios and torque duty ratios are estimated by the applied voltage vector. The proposed DTC-PWM for PMSM was verified by computer simulation.

• 한국측량학회지
• /
• 제36권3호
• /
• pp.135-152
• /
• 2018

The purpose of this study is to propose an optimal fusion method of aerial multi - sensor data to improve the accuracy of land cover classification. Recently, in the fields of environmental impact assessment and land monitoring, high-resolution image data has been acquired for many regions for quantitative land management using aerial multi-sensor, but most of them are used only for the purpose of the project. Hyperspectral sensor data, which is mainly used for land cover classification, has the advantage of high classification accuracy, but it is difficult to classify the accurate land cover state because only the visible and near infrared wavelengths are acquired and of low spatial resolution. Therefore, there is a need for research that can improve the accuracy of land cover classification by fusing hyperspectral sensor data with multispectral sensor and aerial laser sensor data. As a fusion method of aerial multisensor, we proposed a pixel ratio adjustment method, a band accumulation method, and a spectral graph adjustment method. Fusion parameters such as fusion rate, band accumulation, spectral graph expansion ratio were selected according to the fusion method, and the fusion data generation and degree of land cover classification accuracy were calculated by applying incremental changes to the fusion variables. Optimal fusion variables for hyperspectral data, multispectral data and aerial laser data were derived by considering the correlation between land cover classification accuracy and fusion variables.

• 한국전기전자재료학회논문지
• /
• 제29권7호
• /
• pp.414-423
• /
• 2016

In the present study, the $CuN_x-Cu-CuN_x$ layer the partial pressure ratio Cu metal of Ar and $N_2$ gas using a DC magnetron sputtering device, was generated by the In-situ method. $CuN_x$ layer was able to obtain a surface reflectance reduction effect from the advantages of the process and the external light. $CuN_x$ layer is gas partial pressure, DC the Power, the deposition time variable transmittance in response to the thickness and partial pressure ratio, the reflectance was measured. $Ar:N_2$ gas ratio 10:10(sccm), DC power 0.35 A, was derived Deposition time 90 sec optimum conditions. Thus, according to the optimal thickness and the composition ratio was derived surface reflectance of 20.75%. In addition, to derive the value of ${\Delta}$ Ra surface roughness of 0.467. It was derived $CuN_x$ band-gap energy of about 2.2 eV. Thus, to ensure a thickness and process conditions can be absorbed to maximize the light in a wavelength band in the visible light region. As a result, the implementation of the $12k{\Omega}$ base line resistance of using the Cu metal. This is, 5 inch Metal mesh TSP(L/S: $4/270{\mu}m$) is in the range of the reference operation.

• 전자공학회논문지SC
• /
• 제43권4호
• /
• pp.11-20
• /
• 2006

본 논문에서는 초분광 형광영상과 반사영상 융합을 이용한 닭의 종양인식방법을 제안하였다. 형광영상에 밴드비율을 적용하여 피부의 정상과 종양부분을 구분한다. 이를 위해 각각 부분의 확률밀도함수의 중첩된 면적을 최소화하는 방법을 사용하였다. 이 방법으로 획득한 4개의 특정영상에 분할-합병법을 적용하여 형광영상 분류결과를 얻었다. 반사영상 분석에서는 단일 밴드가 정보량에 주는 영향에 근거하여 밴드 선택 방법을 제안하였다. 학습데이터에 의해 투영 축을 선택하는 선형변환을 정의함으로써 영상분류에 효과적인 많은 특징을 확보하였다. 이에 따라 반사영상에서도 세밀한 영상의 해석이 가능하였고 특징 선택의 자동화를 실현하였다. 반사영상에서 획득한 특정영상도 분할-합병법으로 분류하였으며 형광영상의 분류결과와 융합하여 종양을 인식하였다. 모의실험을 통해 제안한 방법은 기존의 방법에 비해 오인식이 낮음을 확인하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 ICEIC The International Conference on Electronics Informations and Communications
• /
• pp.199-203
• /
• 2004

In this paper, we only describe the digital block of two-channel 18-bit analog-to-digital (A/D) converter employing sigma-delta method and xl28 decimation. The device contains two fourth comb filters with 1-bit input from sigma­delta modulator. each followed by a digital half band FIR(Finite Impulse Response) filters. The external analog sigma-delta modulators are sampled at 6.144MHz and the digital words are output at 48kHz. The fourth-order comb filter has designed 3 types of ways for optimal power consumption and signal-to-noise ratio. The following 3 digital filters are designed with 12tap, 22tap and 116tap to meet the specification. These filters eliminate images of the base band audio signal that exist at multiples of the input sample rate. We also designed these filters with 8bit and 16bit filter coefficient to analysis signal-to-noise ratio and hardware complexity. It also included digital output interface block for I2S serial data protocol, test circuit and internal input vector generator. It is fabricated with 0.35um HYNIX standard CMOS cell library with 3.3V supply voltage and the chip size is 2000um by 2000um. The function and the performance have been verified using Verilog XL logic simulator and Matlab tool.

• 한국통신학회논문지
• /
• 제40권7호
• /
• pp.1363-1368
• /
• 2015

본 논문에서는 개구결합 원형편파 마이크로스트립 배열안테나를 제안하였다. 제안한 안테나는 2.4GHz ISM 대역용이고 개구모양은 변형된 H형 슬롯을 사용하였다. 전자파 해석 툴인 HFSS를 반복적으로 사용하여 최적의 안테나 설계 파라미터 값을 찾았다. 배열안테나의 반사손실, 축비, 방사패턴 및 이득을 단일안테나와 비교하였다. 제안한 배열안테나가 2.4GHz ISM 대역 등 여러 분야에서 충분히 사용될 수 있음을 확인하였다.

• 대한조선학회논문집
• /
• 제48권4호
• /
• pp.299-307
• /
• 2011

The offshore plants such as FPSO are subjected to combination loading of environmental conditions (swell, wave, wind and current). Therefore the fatigue damage is occurred in the operation time because the units encounter the environmental phenomena and the structural configurations are complicated. This paper is a research for frequency domain fatigue analysis of wide-band random loading focused on accuracy of fatigue damage estimation regarding the proposed methods. We selected ideal bi-modal spectrum. And comparison between time-domain fatigue analysis and frequency-domain fatigue analyses are conducted through the fatigue damage ratio. Fatigue damage ratios according to Vanmarcke's bandwidth parameter are founded for wide-band. Considering safety, we recommend that Jiao-Moan and Tovo-Benasciutti methods are optimal way at the fatigue design for wide-band response. But, it is important that these methods based on frequency-domain unstably change the accuracy according to the material parameter of S-N curve. This study will be background and guidance for the new frequency-domain fatigue analysis development in the future.

• 한국정보통신학회논문지
• /
• 제17권2호
• /
• pp.287-293
• /
• 2013

인지무선통신(Cognitive radio, CR)은 사용하지 않는 대역을 동적으로 활용할 수 있는 통신 방식이다. 여기서 CR 사용자는 주사용자와 동일한 스펙트럼을 공유하면서 주사용자에 대한 간섭을 최대한 배제해야한다. 일반적으로 각 CR 사용자는 자신이 속한 지역을 센싱하는 것으로 스펙트럼 사용 가능 여부를 판단한다. 하지만 CR 사용자가 다중 경로 페이딩이나 섀도잉와 같은 불확실한 무선 환경에 있을 경우 신호를 정확하게 감지하지 못할 확률이 높아진다. 이때 협력 센싱 기법을 활용할 경우 이러한 무선환경을 극복할 수 있게 된다. 본 연구에서는 협력 센싱 판정을 위해 연판정 기법을 활용할 때 주어진 시스템 요구치를 만족하면서 detection 확률을 향상시킬 수 있는 협력 노드 선택 알고리즘을 제안하였다. 여기서 SNR이 상대적으로 높은 협력 노드에 가중치를 주는 maximum ratio combining(MRC) 방식으로 최적의 협력 노드를 찾았다. 실험 결과, 제안한 알고리즘으로 시스템 요구치에 부합하는 최적의 센싱 노드를 선택할 수 있었다.

• 한국음향학회지
• /
• 제18권1호
• /
• pp.10-15
• /
• 1999

본 연구는 35° Y-X Quartz 기판에 낮은 형상 요소를 갖는 Code Division Multiple Access(CDMA)방식 기지국용 Intermediate Frequency (IF)단 통과대역 필터를 설계하고 제작하는 방법에 대해 연구하였다. 이 기판 위에 임펄스 모델링을 이용하여 낮은 형상 요소를 갖는 표면 탄성파 필터를 제작하기 위해 입력단에는 Apodization weighted형의 빗살무늬 변환기, 출력단에는 Withdrawal weighted형의 빗살무늬 변환기로 구성하였다. 그리고 입출력 IDT의 개수는 리플의 영향을 최소화하기 위해 Kaiser-Bessel 창함수를 이용하였으며, 각각 2200쌍과 1000쌍으로 하였다. IDT 전극의 폭은 3.6㎛, 간격은 3.5㎛였으며 두께는 파장과의 비를 고려해 6000Å으로 할 때 최적의 결과를 얻을 수 있었으며, 구경은 임피던스 정합을 위해 2mm로 하였다. 제작된 SAW필터는 중심 주파수 115.2MHz, 통과대역 폭은 1.27MHz이상, 형상 요소는 1.3이하, 삽입손실 -l5dB 및 저지대역 -45dB이하인 특성을 얻을 수 있었다.

• 펄프종이기술
• /
• 제35권1호
• /
• pp.41-47
• /
• 2003

Recently, interest in utilization plan of recycling paper have been enhanced. Therefore, this research aimed to develop the manufacture process of cellulose acetate using old newsprint by acetosolv pulping process. And the manufactured cellulose acetate was also analyzed, especially based on chemical properties. The summarized results in this research were as follows; Reaction time, kind and amount of catalyst, and ratio of liquor to material were varied during acetosolv pulping process of old newsprint. Ratio of liquor to material did not give the significant difference in reaction product. Delignification rate was increased with increasing reaction time during acetosolv pulping, but yield and degree of substitution decreased with increasing reaction time. Sulfuric acid are better catalyst than hydrochloric acid in acetosolv pulping process for old newsprint, and optimal addition amount of catalyst was 1% based on reaction material. Delignification, yield, and degree of substitution were influenced by the catalyst and reaction time. Under pulping condition of $120^{\circ}C$ in 1/12 liquor to material ratio and 60min, degree of substitution was about 0.7. The acetylation reaction was not completely caused by these reaction condition. The examination of the FT-IR spectra revealed that absorption band(1200$\textrm{cm}^{-2}$, 1,750$\textrm{cm}^{-1}$) caused by carbonyl group were confirmed.