• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.335-335
• /
• 2008

Phosphate glass samples with various $Cr_2O_3$ and $Er_2O_3$ contents based upon $55P_2O_5\cdot24BaO\cdot10K_2O\cdot4Al_2O_3\cdot6Yb_2O_3$ were prepared. The prepared glass compositions are dehydrated using gas bubble flow method in open system and investigated the effects of the eliminating of OH groups from the glass melts with bubbling time. It was found that the probability of $Er^{+3}$ fluorescence quenching by OH groups oscillations linear depends upon the OH groups absorption coefficients in the maximum of the stretch vibrations band at $3500cm^{-1}$ while $Er^{+3}$ concentration range is between $1.6\times10^{19}$ and $21.2\times10^{19}$ ion/$cm^3$.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.6
• /
• pp.203-207
• /
• 2009

We have investigated the effect of ambient gases on the structural, electrical, and optical characteristics of ITO thin films intended for use as anode contacts in OLED (organic light emitting diodes) devices. These ITO thin films are deposited by radio frequency (RF) magnetron sputtering under different ambient gases (Ar, Ar+$O_2$, and Ar+$H_2$) at $300{^{\circ}C}$. In order to investigate the influences of the oxygen and hydrogen, the flow rate of oxygen and hydrogen in argon mixing gas has been changed from 0.5 sccm to 5 sccm and from 0.01 sccm to 0.25 sccm, respectively. The intensity of the (400) peak in the ITO thin films increased with increasing $O_2$, flow rate whilst the (400) peak was nearly invisible in an atmosphere of Ar+$H_2$. The electrical resistivity of the ITO thin films increased with increasing $O_2$ flow rate, whereas the electrical resistivity decreased sharply under an Ar+$H_2$ atmosphere and was nearly similar regardless of the $H_2$ flow rate. The change of electrical resistivity with changes in the ambient gas composition was mainly interpreted in terms of the charge carrier mobility rather than the charge carrier concentration. All the films showed an average transmittance of over 80% in the visible range. The OLED device was fabricated with different ITO substrates made with the configuration of ITO/$\alpha$-NPD/DPVB/$Alq_3$/LiF/Al in order to elucidate the performance of the ITO substrate. Current density and luminance of OLED devices with ITO thin films deposited in Ar+$H_2$ ambient gas is the highest among all the ITO thin films.

• KSBB Journal
• /
• v.24 no.2
• /
• pp.140-148
• /
• 2009

The microbial biosurfactants can be substituted to the chemical detergents in some industrial processes. In this study we developed a biotechnological processes for the biosurfactants with microorganisms. The biosurfactants have a lot of advantages in comparision with the chemical surfactants. They are proenvironmental even during and after industrial use. But there are not so many kinds of biosurfactants. The production cost and the end price is much higher than the chemical surfactants. But nowdays there are many kinds of microorganisms, which can produce the surfactants in large quantity and fast. We tried to develop a production process for the large scale with some microorganisms. At first Candida bombicola KCTC 7145, Sphingomonas chungbukensis KCTC 2955 and Sphingomonas yanoikuyae KCTC 2818 are cultivated and studied. For the large scale production process we used molasses as a complex medium and tried to optimize the process. Molasses contains 17 to 25% of water, 45 to 50% of sugar and 25% of carbohydrate, it can be fully used as a substrate. The microorganisms have been cultivated in the diluted media with molasses 2, 5, 8 and 10%, respectively, The optimal conditions for the cultivation and the production process have been studied. For the study the optical density, glucose concentration and the surface tension were measured. Candida bombicola KCTC 7145 and the 5% molasses media was selected as an optimal condition for the production process of a biosurfactant. During cultivation of Candida bombicola KCTC 7145 in the 5% molasses medium kerosene and corn oil were added for promoting the biosurfactants.

• Korean Chemical Engineering Research
• /
• v.46 no.4
• /
• pp.686-691
• /
• 2008

There are no many research reports on the preparation of ZnO by electrochemical oxidation since the zinc oxide is very easily dissolved in an acidic or basic environment, even though zinc oxides have attracted many attentions because of their optical/electrical properties. In this paper, we describe the fabrication of self-ordered stripes of ZnO by anodization of Zn in an ethanolic sulfuric acid. The formation of stripes of ZnO originating from Zn is attributed to water-selective dissolution of ZnO during anodization. We study in detail the effects of concentration of $H_2SO_4$, applied potential, anodization time, and addition of a small amount of water on the fabrication of stripes of ZnO. Mechanisms for the fabrication of ZnO stripes are discussed in terms of the above-mentioned effects.

• Elastomers and Composites
• /
• v.39 no.1
• /
• pp.36-41
• /
• 2004

Solid polymer electrolytes were prepared by UV irradiation of the blends consisting of poly(ethylene oxide)(PEO), epoxy diacrylate(EDA) and LiClO_4$. Conductivities of the electrolyte films were measured as a function or blend composition, salt concentration and temperature. The electrolyte having the composition of poly(ethylene oxide) (70% by weight)/epoxy diacrylate (30% by weight) with mole ratio of 10 of ethylene $oxide/Li^+$ exhibited a high ionic conductivity of $1.2{\times}10^{-5} S/cm$ at $25^{\circ}C$. This blend is transparent and shows elastomeric properties. Morphological studies by means of differential scanning calorimetry, X-ray diffraction and polarized optical microscopy indicated that the cured epoxy chains in the blends inhibit the crystallization of poly (ethylene oxide) and thereby induce the blend systems to be completely amorphous in certain compositions.

• Korean Journal of Optics and Photonics
• /
• v.21 no.2
• /
• pp.69-73
• /
• 2010

We propose a method to enhance the response time of a twisted nematic liquid crystal (TN-LC) cell using an anisotropic polymer. Polymer networks are formed by the phase separation between a LC and a UV-curable polymer. A TN-LC cell is exposed to UV light after the mixture of LC and anisotropic polymer is injected into the TN-LC cell. As a result, turn-off time of a TN-LC cell can be decreased remarkably without any loss of the transmittance. The turn-off time of a TN-LC cell with pure LC was 16 ms, but those of polymer networked TN-LC cells were 12, 11, and 9 ms when the concentration of the polymer was 3, 5, and 10 wt%, respectively. Moreover, by virtue of the polymer network, the backflow effect and the delay time generated during the turn-off process disappeared.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.141-148
• /
• 2019

Electronic substrates used in a mobile device is composed of various materials, and when the temperature is changed during manufacturing or operating, thermal deformation and stress concentration occur due to the difference in thermal expansion coefficient of each material. The shadow moiré technique is a non-contact optical method that measures shape or out-of-plane displacement over the entire area, but it is necessary to overcome the Talbot effect for high sensitivity applications. In this paper, LED light sources of various wavelengths was used to overcome the Talbot effect caused in the shadow moiré technique. By using the phase shift method, an experimental method to retain the measurement sensitivity within 10 ㎛/fringe was proposed and evaluated, and this method is applied to the thermal deformation measurement of the mobile electronic substrate. In the case of using white light, there were several areas that could not be measured due to the Talbot effect, but in the case of using blue LED light, it was shown that a precise moiré pattern with a sensitivity of 6.25 ㎛/fringe could be obtained in most areas.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.6
• /
• pp.389-393
• /
• 2000

High-quality $Er^{3+}$ doped Mg : $LiNbO_3$single crystal fibers were grown by a micro-pulling down ($\mu$-PD) method. Single crystal fibers were pulled down through the nozzle, at a pulling down rate of 0.5 mm/min and using a Pt crucible with a nozzle 1 mm in diameter in air atmosphere. Defects such as bubbles, cracks and inclusions were not detected in any of the grown crystals. The optical transmission of Er : Mg : $LiNbO_3$crystal was measured and the energy levels of $Er_2O_3$ ion could be calculated. The photoluminescence spectrum of crystal fibers showed an energy band emission with the strongest line corresponding to the $^4I_{3/2}{\to}^4I_{15/2}$transition. The concentration dependence of the entire wavelength region emission intensity upon excitation intensity measured emission intensity for the 3 mol% MgO doped fibers was larger than that for the 1, 5 mol% MgO doped fibers.

• Korean Journal of Optics and Photonics
• /
• v.19 no.3
• /
• pp.193-198
• /
• 2008

A novel refractive index sensor, which consists of polymer channel waveguide overlaid with $TiO_2$ thin film, is demonstrated. To evaluate the fabricated sensor, we measured the polarimetric interference induced by concentration change of injected glycerol solution. Our experimental results show that thicker $TiO_2$ film improves the sensitivity of the polarimetric interferometer. For the fabricated waveguide with a 20 nm thick $TiO_2$ film, the measured index change to lead phase variation of $2{\pi}$ is $1.8{\times}10^{-3}$.

• Korean Journal of Crystallography
• /
• v.8 no.1
• /
• pp.26-32
• /
• 1997

Quartz single crystals were grown hydrothermally and growth defects such as dislocations, etch channels and impurities were examined. Growth rates were 0.25-0.65 mm/day under the growth conditions of following. 1. Mineralizer: $4wt.\%$ NaOH. 2. Growth temperature: $340-360^{\circ}C$. 3. Temperature gradient: $20-40^{\circ}C$. 4. Seed: ZY plate. 5. Nutrient: synthetic quartz. Defects of the quartz which was grown with optical grade synthetic nutrient, low dislocation density seed and horizontal seed setting technique were as follows. 1. Dislocation density: 20.0 each/$cm^2$. 2. Etch channel density: 5.0 each/$cm^2$ (1st grade by IEC 758 standard). 3. Impurity (larger than 10$\mu$) concentration: 2.4 each/$cm^3$ (Ia grade by IEC 758 standard). 4. Alpha value: 0.019 (A grade by IEC 758 standard).