• Journal of the Korean Vacuum Society
• /
• v.18 no.1
• /
• pp.30-36
• /
• 2009

The effects of $HfO_2$ film thickness on electrical, optical, and structural properties were investigated. We fabricated ITO/$HfO_2$/ITO metal-insulator- metal (MIM) capacitor using transparent conducting oxide. When $HfO_2$ film thickness increase from 50 nm to 300 nm, dielectric constant of $HfO_2$ was decreased from 20.87 to 9.72. The transparent capacitor shows an overall high performance, such as a dielectric constant about 21 by measuring the ITO/$HfO_2$/ITO capacitor structures and a low leakage current of $2.75{\times}10^{-12}\;A/cm^2$ at +5 V. Transmittance above 80% was observed in visible region.

• Journal of the Korea Convergence Society
• /
• v.12 no.2
• /
• pp.185-191
• /
• 2021

The characteristics of the foundry sand were analyzed for water jacket core required to prevent structural deformation from the heat generated in the cylinder bore during the casting of the cylinder block of an automobile. The sand core tensile strength tester, AFS-GFN, and optical microscope were used to evaluate the its properties. If the SiO2 content is high in the foundry sand, the dimensional defects and veining defects occur due to high temperature expansion. Also, if it is too low, the core breakage, porosities, chemical burn-on defects occur. The particle size index and grain shape influenced the core strength and resin consumption, resulting in fluctuations in defect types. The higher the alkalinity of the dried sand, the lower the core strength. And the more basic, the lower the core strength. At the resin content of 1.6~1.8%, the increase in core strength after 1 hour curing was approximately at its maximum.

• Korean Journal of Materials Research
• /
• v.23 no.9
• /
• pp.477-482
• /
• 2013

We investigated the detection properties of nitrogen monoxide (NO) gas using transparent p-type $CuAlO_2$ thin film gas sensors. The $CuAlO_2$ film was fabricated on an indium tin oxide (ITO)/glass substrate by pulsed laser deposition (PLD), and then the transparent p-type $CuAlO_2$ active layer was formed by annealing. Structural and optical characterizations revealed that the transparent p-type $CuAlO_2$ layer with a thickness of around 200 nm had a non-crystalline structure, showing a quite flat surface and a high transparency above 65 % in the range of visible light. From the NO gas sensing measurements, it was found that the transparent p-type $CuAlO_2$ thin film gas sensors exhibited the maximum sensitivity to NO gas in dry air at an operating temperature of $180^{\circ}C$. We also found that these $CuAlO_2$ thin film gas sensors showed reversible and reliable electrical resistance-response to NO gas in the operating temperature range. These results indicate that the transparent p-type semiconductor $CuAlO_2$ thin films are very promising for application as sensing materials for gas sensors, in particular, various types of transparent p-n junction gas sensors. Also, these transparent p-type semiconductor $CuAlO_2$ thin films could be combined with an n-type oxide semiconductor to fabricate p-n heterojunction oxide semiconductor gas sensors.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.178-178
• /
• 2007

II-VI의 넓은 밴드갭 (3.37 eV)을 가지는 ZnO는 solar cells, transparent conductive electrodes, ultraviolet light emitters, and chemical sensors 등에 응용되고 있다. 특히 고효율 ZnO계 발광 소자 구현을 위하여 MgO (7.7eV), CdO (2.0eV) 등의 고용을 통한 밴드갭을 엔지니어링 하며, 단파장 영역의 광원을 확보하기 위하여 MgO 첨가를 통한 밴드갭 에너지를 증가시키는 방향으로의 연구가 활발하다. 그러나 ZnO의 wurtzite 구조와 MgO의 rocksalt 구조의 상이한 결정구조로 인하여 Mg의 고용한계는 4 at. %, 4.1 eV 알려져 있다. 본 실험에서는 p-type Si (100), c-sapphire (0002)과 GaN 기판 위에 MgO (99.999 %)와 ZnO (99.999 %) 두가지 타겟을 사용하여 RF co-스퍼터링법으로 ZnMgO 박막을 증착 하였다. 이때 ZnO 타겟의 power 밀도는 고정 시키고 MgO 타겟의 power 밀도를 변화 시키며 Mg의 함량을 조절하여 그에 따른 광학적 구조적 특성의 변화를 연구 하였다. 성장된 ZnMgO 박막은 MgO 타겟의 power 밀도가 증가할 때 Mg의 함량이 10 at. %까지 증가 하며, 그에 따른 표면의 거칠기 및 입계 크기가 감소하며, 박막의 성장속도 또한 감소함을 SEM과 AFM을 통하여 알 수 있었다. XRD를 동하여 ZnMgO 박막의 (0002) peak의 위치는 $34.50^{\circ}{\sim}34.7^{\circ}$로 오른쪽으로 이동하며, c-축으로 성장하였음을 알 수 있다. PL과 UV룰 동하여, Mg의 함량이 증가 할수록 박막의 밴드갭 에너지는 3.2 eV에서 4.1 eV 로 증가하였다.

• Journal of Technologic Dentistry
• /
• v.31 no.1
• /
• pp.23-36
• /
• 2009

The goal of esthetic restoration is to achieve morphologic, optical, and biologic acceptance. Creation of a natural looking ceramic restoration, which blends harmoniously with surrounding dentition, is not always achieved. A successful color match is an important aspect of any esthetic dental restoration. Since natural enamel has inherent translucency, it is important that ceramic restorations reproduce the translucency and color of the natural teeth. However, the final color match of porcelain crowns to adjacent natural dentition remains some problem. Difficulties related to color matching arise from the structural differences that exist between metal ceramic crowns and natural teeth, the limited range of available ceramic shades, inadequate shade guides, different types of metal alloys, repeated firing, the condensation technique, and varying compositions of ceramic materials. Many factors contribute to the esthetic success of dental restoration: optical properties such as color and its elements of hue, value, and chroma; translucency and opacity; light transmission and scattering; and metamerism and fluorescence. The purpose of this study was to determine the color changes of metal-ceramic system with different veneering porcelain powder after repeated firing. The objectives of this in vitro study were to measure the lightness($L^*$), chromaticity($a^*$), chromaticity($b^*$), chroma($C^*$), hue(h), reflectance(%), color difference(${\Delta}E$). The following conclusions were obtained: 1. An increase in the number of firings resulted in decrease in lightness($L^*$) but increase in chromacticity($a^*$) with all porcelain. After the second sintering resulted in decrease in chromacticity($b^*$) with opaque-dentin porcelain and dentin porcelain but in increase with enamel porcelain and translucency porcelain. And after the second sintering resulted in decrease in chroma($C^*$) with opaque-dentin porcelain and dentin porcelain, but on the whole side in decrease with enamel porcelain and translucency porcelain. 2. After the second firing, a increase in the number of firings resulted in decrease reflectance(%) in all wavelength. 3. There were noticeable color differences(${\Delta}E$) between first sintering and multiple firings(dentin porcelain: 5.29~8.15, opaque-dentin porcelain: 4.83~8.2, enamel porcelain: 8.93~13.15, translucency porcelain: 9.37~12.91), but the color difference(${\Delta}E$) after second sintering were down to 4.87 in all porcelain. 4. Given the NBS Criteria, a 'trace' was not found this study but a 'slight' was found 2-3, 3-5 in dentin porcelain, 2-3 in opaque-dentin porcelain, 3-5, 5-10 in enamel porcelain and translucency porcelain, a 'noticeable' was 2-5, 3-10, 5-10 in dentin porcelain and opaque-dentin porcelain, 2-3, 2-5, 3-10 in enamel porcelain 2-3, 3-10 in translucency porcelain, an 'appreciable' was 1-2, 1-3, 2-10 in dentin porcelain 1-2, 1-3, 2-10, 3-10 in opaque-dentin porcelain, 2-10 in enamel porcelain, 2-5, 2-10 in translucency porcelain, a 'much' was 1-5, 1-10 in dentin porcelain and opaque-dentin porcelain, 1-2, 1-3, 1-5 in enamel porcelain 1-2, 1-3, 1-5, 1-10 in translucency porcelain, a 'very much' was 1-10 in enamel porcelain.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.7
• /
• pp.627-633
• /
• 2009

Composite has become one of the most frequently used material for a tube of satellite camera due to its attractive characteristics. However, laminated composites can be weakened by delamination which comes from interlaminar stress. Such failure mode cause structural instability of the camera as well as degradation of optical quality. Therefore composite tube should be robust in delamination. Also, composite tube should have high stiffness, sufficient high natural frequency and small coefficient of thermal expansion. The design procedures presented in this paper are based on design of experiments. The experiments for mechanical analysis are designed by the tables of orthogonal arrays. In order to manipulate the various mechanical properties systematically, multiple-attribute decision making(MADM) is employed. Through analysis of variance and F-test, the critical design variables which have dominant influences on mechanical performance are determined. Finally improved ply angles for composite tube are determined.

• Polymer(Korea)
• /
• v.32 no.5
• /
• pp.478-482
• /
• 2008

The effect of 1,3-dioxolane on the structural development in the optical polycarbonate film was studied. The 1,3-dioxolane was used as an environmental friendly solvent for manufacturing solution-cast polycarbonate film instead of methylene chloride. The evaporation rate in film drying process decreased due to the high boiling temperature of 1,3-dioxolane. This caused the crystallization in the polycarbonate film. As a result, The increase of crystallinity and roughness led to the decrease of light transmissivity. It was also found that the lowering of mechanical properties in polycarbonate film was attributed to the morphological change due to the solvent evaporation rate in film drying process.

• Korean Journal of Optics and Photonics
• /
• v.11 no.5
• /
• pp.323-329
• /
• 2000

In this study we have calculated an ideal complex refractive index of a TiN trim used in a layer of anl1reilecnon (I\R) coatmg, [air$ISiO_2ITiNIglass$] in the visible. Also we simulated the rellectance of lwo-layer AR coating by varying the thicknesses of TiN and $SiO_2$ layers, respecl1vely. The simolation results show that we can controllhe lowest reflectance and AR band of tile AR coating. The TIN fihns were fabricated by a RF magnetron sputtering apparalus. The chemical, structural and electrical properties of TiN fih11S were inveshgated by the Rutherford backscattering spech'oscopy (RBS), atomic force microscope (AFM) and 4-point probe. The optical properlies were inve,tigated by the spectrophotometer and vanable angle spectroscopic ellipsometer (VASE). The smface roughness of TiN flhns \vas $9~10\AA$. TIle resistivity of TiN films was TEX>$360~730\mu$\Omega $ cm. The ,toichlOllletry of TiN film was 1'1: O:N = I: 0.65 :0.95 and ilic oxygen wa~ found on ilie smface. With these experimental and simu]al1on resulLs, we deposited duo: two-layer AR coating, [air$ISiO_2ITiNIglass$] and the refleClance was under 0.5% ill the regIOn of 440-650 run. 0 run.

• Journal of Sensor Science and Technology
• /
• v.12 no.2
• /
• pp.66-71
• /
• 2003

Pt/AlGaN Schottky-type UV photodetectors were designed and fabricated. A low-temperature AlGaN interlayer buffer was grown between the AlGaN and GaN film in the diode structure epitaxy to obtain crack-free AlGaN active layers. A comparison was then made of the structural, electrical, and optical characteristics of two different diodes: one with an AlGaN($0.5\;{\mu}m$)/n+-GaN(2 nm) structure (type 1) and the other with an AlGaN($0.5\;{\mu}m$)/AlGaN interlayer($150\;{\AA}$)/n+-GaN($3\;{\mu}m$) structure(type 2). A crack-free AlGaN film was obtained by the insertion of a low-temperature AlGaN interlayer with an aluminum mole fraction of 26% into the $Al_xGa_{1-x}N$ layer. The fabricated Pt/$Al_{0.33}Ga_{0.67}N$ photodetector had a leakage current of 1 nA for the type 1 diode and $0.1\;{\mu}A$ for the type 2 diode at a reverse bias of -5 V. For the photoresponse measurement, the type 2 diode exhibited a cut-off wavelength of 300 nm, prominent responsivity of 0.15 A/W at 280 nm, and UV-visible extinction ratio of $1.5{\times}10^4$. Accordingly, the Pt/$Al_{0.33}Ga_{0.67}N$ Schottky-type ultraviolet photodetector with an AlGaN interlayer exhibited superior electrical and optical characteristics and improved UV detecting properties.

• Clean Technology
• /
• v.25 no.1
• /
• pp.14-18
• /
• 2019

In general after the etching process, waste etching solution contains metals. (ex. Nickel (Ni), Chromium (Cr), Zinc (Zn), etc.) In this work, we proposed a recycling process for waste etching solution and refining from waste liquid contained nickel to make nickel metal nano powder. At first, the neutralization agent was experimentally selected through the hydrolysis of impurities such as iron by adjusting the pH. We selected sodium hydroxide solution as a neutralizing agent, and removed impurities such as iron by pH = 4. And then, metal ions (ex. Manganese (Mn) and Zinc (Zn), etc.) remain as impurities were refined by D2EHPA (Di-(2-ethylhexyl) phosphoric acid). The nickel powders were synthesized by liquid phase reduction method with hydrazine ($N_2H_4$) and sodium hydroxide (NaOH). The resulting nickel chloride solution and nickel metal powder has high purity ( > 99%). The purity of nickel chloride solution and nickel nano powders were measured by EDTA (ethylenediaminetetraacetic) titration method with ICP-OES (inductively coupled plasma optical emission spectrometer). FE-SEM (field emission scanning electron microscopy) was used to investigate the morphology, particle size and crystal structure of the nickel metal nano powder. The structural properties of the nickel nano powder were characterized by XRD (X-ray diffraction) and TEM (transmission electron microscopy).