• Journal of electromagnetic engineering and science
• /
• v.9 no.3
• /
• pp.146-151
• /
• 2009

This paper presents a low-loss broadband balun that uses a coplanar waveguide-to-slotline field transformation. It operates over a very wide frequency range and is of compact size since it does not depend on a resonant structure. To analyse imbalance, the coplanar wavelength(CPW) input ground is connected to the CPW output ground through various capacitors to introduce common-mode impedances. As the common-mode impedance increased the imbalance became significantly higher at the higher-frequency band compared with the lower-frequency band. The bias-circuit approach is used to improve the operation bandwidth of the lower-frequency band. The measured results show a passband of 200 MHz to 2 GHz, an insertion loss of less than 0.75 dB, and a size of $20{\times}14\;mm$. The amplitude imbalance is approximately 0.3 dB and the phase imbalance is less than $6^{\circ}$ over the entire operational range.

• Proceedings of the KIEE Conference
• /
• 2008.10b
• /
• pp.520-521
• /
• 2008

This paper describes a low voltage, low-power CMOS buck DC/DC converter, which has a simple common-gate current sensing circuit. It consumes low power because it includes less transistors than other converters which use operational amplifiers for current sensing. The designed DC-DC converter is fabricated in a 0.18um CMOS technology. A maximum efficiency of 88% has been obtained with the proposed circuit. It has $2V{\sim}3.7V$ input voltage range, $1V{\sim}2.5V$ output voltage range and maximum output current of 1000mA.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.100-108
• /
• 2016

This paper presents a simple high efficiency full-bridge DC-DC converter using a series resonant capacitor. The proposed converter achieves the zero voltage switching of the primary switches under a wide range of load conditions and reduces the high circulating current in the freewheeling mode using the leakage resonant inductance and the series resonant capacitor. Thus, the proposed converter overcomes the drawbacks of the conventional full-bridge DC-DC converter and improves its overall system efficiency. Its structure is simplified by using the leakage inductance of the transformer as the resonant inductance and omitting the DC output filter inductance. Also it can operate over a wide range of input voltages. In this paper, the operational principle, analysis and design example are described in detail. Finally, the experimental results from a 650W (24V/27A) prototype are demonstrated to confirm the operation, validity and features of the proposed converter.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.2
• /
• pp.130-135
• /
• 2015

Recently, as a result of the application of large and multi-blade propellers with high efficiency for large vessels, the vertical bending stiffness of propulsion shafting system tends to be declined. For some specific vessels, the shaft arrangement leads to the forward stern tube bearing to be omitted, decreasing vertical bending stiffness. In this respect, decreased vertical bending stiffness causes the problem which is the blade order resonance frequency to be placed within the operational rpm range of propulsion shafting system. To verify whirling vibration, the measurement should be carried out covering from operating rpm up to target rpm, however, the range is un-measurable generally. In order to resolve the measurement issue, this study shows the measuring method and the assessment method of relevant natural frequency of whiling vibration by using measured harmonic order component of whirling vibration.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.8 no.1
• /
• pp.40-46
• /
• 2009

This paper presents a self-sustaining system, and an effective method in enhancing overall energy efficiency. The proposed system consists of the two major nodes: a slave node, which contains the environment information (e.g., temperature, humidity, etc.); and a master node, which communicates with the slave nodes, and transmit the slave node's information to users. All slave nodes are under control of the master node. Each slave node uses two power sources: the piezoelectric power generator (PPG); and the continuous wave from the master node. The paper highlights the basic operational principle, each node's specifications, and experimental data for performance verification. The two nodes successfully communicate each other in a range of 3.3m (maximal range), where the user's computer is wired the master node.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.8
• /
• pp.1260-1264
• /
• 1990

A voltage controlled CMOS operational transconductance amplifier (OTA), whose transconductance is directly proportional to the DC bias voltage, has been designed for many electronic circuit applications. It consists of a differential pair and three ourrent mirrors. The SPICE simulation shows that the conversion sensitivity of the OTA is 41.817 \ulcornerho/V and the linearity error is less than 0.402% over a bias voltage range from -2. OV to 1. OV. Electrically tunalble filters based on voltage controlled impedances, which are realized with OTA's, also have been designed. The SPICE simulation shows that a second-order bandpass filter, whose center frequency is 23KHz at -1. OV, has the conversion sensitivity 6.6KHz/V and the linearity error less than 0.822% over a voltage range from -2.OV tp 1.OV, Tne OTA has been laid out with the 3\ulcorner n-well CMOS design rule adopted in ISRC (inter-university semiconductor research center). The chip size was about $0.756x0.945mm^2$.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.759-762
• /
• 2002

In this paper, a voltage-controlled linear variable resistor (VCLVR) using a floating-gate MOS-FET (FG-MOSFET) is proposed. The proposed-circuit is the grounded VCLVR consists of only an ordinary MOSFET and an FG-MOSFET. The advantage of the proposed VCLVR are low-voltage and wide-input range. Next, as applications, a floating-node voltage controlled variable resistor and an operational transconductance amplifier using the proposed VCLVRs are proposed. The performance of the proposed circuits are characterized through HSPICE simulations with a standard 0.6 ${\mu}$m CMOS process. simulations of the proposed VCLVR demonstrate a resistance value of 40 k$\Omega$ to 338 k$\Omega$ and a THD of less than 1.1 %.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.133-136
• /
• 2002

This paper discusses the design of a sample-and -hold amplifier(SHA) that has a 12-bit resolution with a 100 MS/s speed. The sample-and-hold amplifier uses the open-loop architecture with hold-mode feedthrough cancellation for high accuracy and high sampling speed. The designed SHA is composed of input buffer, sampling switch, and output buffer with additional amplifier for offset cancellation Hard Ware. The input buffer is implemented with folded-cascode type operational transconductance Amplifier(OTA), and sampling switch is implemented with switched source follower(SSF). A spurious free dynamic range (SFDR) of this circuit is 72.6 dB al 100 MS/s. Input signal dynamic range is 1 Vpp differential. Power consumption is 65 ㎽.

• Journal of Mechanical Science and Technology
• /
• v.17 no.12
• /
• pp.1938-1948
• /
• 2003

This paper represents that an enhanced genetic algorithm (EGA) is applied to optimal design of a squeeze film damper (SFD) to minimize the maximum transmitted load between the bearing and foundation in the operational speed range. A general genetic algorithm (GA) is well known as a useful global optimization technique for complex and nonlinear optimization problems. The EGA consists of the GA to optimize multi-modal functions and the simplex method to search intensively the candidate solutions by the GA for optimal solutions. The performance of the EGA with a benchmark function is compared to them by the IGA (Immune-Genetic Algorithm) and SQP (Sequential Quadratic Programming). The radius, length and radial clearance of the SFD are defined as the design parameters. The objective function is the minimization of a maximum transmitted load of a flexible rotor system with the nonlinear SFDs in the operating speed range. The effectiveness of the EGA for the optimal design of the SFD is discussed from a numerical example.

• Mass Spectrometry Letters
• /
• v.4 no.4
• /
• pp.91-94
• /
• 2013

We performed computer simulations to improve transmission efficiencies of a dual ion funnel system implemented on an FT-ICR MS. We found that the low m/z range from 50 to 150 could be significantly improved by operating the two ion funnels at different RF amplitudes. These new operational conditions could be applied to analyze metabolome samples, which require high sensitivity in the m/z range from 50 to 1,000.