This study was undertaken to obtain the fundamental knowledges on the weld deflects and it's realtime monitoring method. The paper describes the results of high speed photography, acoustic emission (AE) detection and plasma light emission (LE) measurements during $CO_2$ laser welding of STS 304 stainless steel and A5083 aluminum alloy in different welding condition. The characteristic frequencies of plasma and keyhole fluctuations at different welding speed and shield gases were measured and compared with the results of Fourier analyses of temporal AE and LE spectra, and they had considerably good agreement with keyhole and plasma fluctuation. Namely, the low frequency peaks of AE and LE shifted to higher frequency range with the welding speed increase, and leer the argon shield gas it was higher than that in helium and nitrogen gases. The low frequencies dominating in fluctuation spectra of LE probably reflect keyhole opening instability. It is possible to monitor the weld bead deflects by analyzing the acoustic and/or plasma light emission signals.
This study was conducted to develop a heating system for a fuel cell-driven electric vehicle. The system consists of a compressor, an expansion device and three heat exchangers. A conventional air source heat exchanger is used as primary heat exchanger of the system, and an additional water source heat exchanger is used as a pre-heater to supply heat to the upstream air of the primary heat exchanger. On the other hand, the third heat exchanger consists of a water-to-refrigerant heat exchanger. The heat source of the pre-heater and the water-refrigerant heat exchanger is the waste heat from the fuel cell's stack. In the experiment, the indoor and the outdoor air temperature were fixed, and the compressor speed, EEV opening and waste heat temperature were varied. The results indicate that the $COP_h$ of the proposed system is 3.01 when the system is operating at a 1,200 rpm compressor speed, 50% EEV opening, and $50^{\circ}C$ waste heat source temperature in air pre-heater operation. However, when the system uses a water-refrigerant heat exchanger, the $COP_h$ increases to up to 9.42 at the same compressor speed and waste heat source temperature with 75% EEV openings.
본 연구는 현재 국내에서 사용되는 쌍끌이 중층망 어구어법에서 문제점으로 지적되고 있는 고속예망에서 망고의 제어가 어렵다는 점, 망목에 뜸이 걸려서 파망이 자주 일어나는 점, 네트드럼에 감기는 어구부피가 너무 크다는 점 등의 해결방법으로 무부자 쌍끌이 중층망의 모형실험을 통하여 우리 나라 쌍끌이 중층망에 대한 적용 가능성을 검토하는데 있다. 이를 위하여 850ps급 쌍끌이 기선저인망어선에서 현재 사용되는 실물망을 1/100로 축소 제작한 모형망에서 뜸을 모두 제거하고 끌줄을 양쪽으로 각각 두가닥으로 분리한 후 추를 부착하여 아래끌줄의 길이를 조절함으로써 망고를 제어할 수 있는 무부자 쌍끌이 중층망의 모형어구를 제작하여 회류수조에서 유속에 대한 아래끌줄의 길이에 따른 어구의 전개성능 등을 규명하고 기준형과 비교 분석한 결과를 요약하면 다음과 같다. 1. 유체저항은 무부자망이 기준형보다 약 10∼20%정도 작았으며, 무부자망의 유체저항은 동일유속에서 아래끌줄이 길어짐에 따라 약 1ton씩 증가하였다. 또, 동일유속에서 dL이 10m씩 증가함에 따라 아래끌줄에 작용하는 저항은 약 5%씩 감소하고, 그 반면에 윗 끌줄에 작용하는 저항이 증가하였다. 2. 망고는 직선에 가까운 지수함수적으로 감소하는 경향을 보였으며, 동일유속에서 아래끌줄이 길어짐에 따라 증가하여 로그함수적인 경향을 보였다. 또한, 망고감소율은 무부자망의 경우가 기준형보다 작게 나타났으며, 그 차이는 유속이 증가함에 따라 더욱 커져 dL이 30m인 무부자망을 기준으로 3.0knot일 때 12%, 4.0knot일 때 25%로 나타났다. 3. 망폭은 유속이 증가함에 따라 약 2m 내외로 거의 일정하였으며 무부자망이 기준형보다 크게 나타났다. 4. 망구면적은 유속이 증가함에 따라 지수함수적으로 감소하는 경향을 보였으며, 망구면적의 감소율은 기준형보다 무부자망이 더 작게 나타났다. 여과량은 유속이 증가함에 따라 로그함수적인 경향을 보였으며 기준형이 3.0knot 이상에서 급격히 감소하였지만, 무부자망은 4.0knot까지 증가하였다가 완만하게 감소하였다. 5. dL의 최대적정길이는 망구면적 및 여과량이 최대인 30m일 때이며, 추의 최적위치는 4개의 그물목줄이 연결되는 지점이었다.
한국마린엔지니어링학회 2000년도 춘계학술대회 논문집(Proceeding of the KOSME 2000 Spring Annual Meeting)
/
pp.45-51
/
2000
Investigators who study on combustion in the cylinders of reciprocating piston type internal combustion engines have been encountered embarrassments due to the difficulties of adjusting specific parameter without interfacing other parameters such as cylinder wall temperature composition of gas in the cylinder existence of cylinder lubricant etc. Rapid compression-expansion machine the position and speed of piston of which are able to be controlled by means of a system controlled electrically and speed of piston of which are able to be controlled by means of a system controlled electrically and actuated hydraulically could be utilized as one of the most preferable countermeasures against those difficulties. Several units of rapid compression-expansion machines were developed but the speed up of frequency of piston movement still is the problem to be improved to cope with actual speed of internal combustion engines. Authors designed and manufactured a new rapid compression-expansion machine electrically controlled hydraulically actuated and computer programed and then examined the performance of one. Results of a set of experiments revealed acquirements of certain improvement of frequency of piston movement preserving the stability of system response and reproducing accurate compression ratio of cylinder those are the key function for the in-cylinder combustion experiments of internal combustion engines.
한국형 고속철도인 KTX가 2004년 개통된 이후, 우리나라에서도 철도의 이용도가 급증했다. 개선되는 철도 기술과 함께, 예전에 비해 열차의 속도 또한 빠르게 발전하였다. 그러나 이러한 열차속도의 발전은 철도 통신에 있어서 열차 속도 증가로 인한 도플러 효과와 이에 대한 보상이라는 새로운 이슈를 제기하였다. 이러한 도플러 효과는 통신하는 대상의 속도에 따라 주파수 변이를 일으키며, 이는 신호의 왜곡으로 이어져, 통신성능에 좋지 않은 영향을 미칠 수 있다. 따라서, 이러한 도플러 효과에 대한 문제는 철도 무선 통신에 있어서, 반드시 해결해야 할 문제이다. 본 논문에서는 앞으로 발생할 고속의 철도 통신에서 발생하는 도플러 효과와 발생하는 도플러 효과에 대한 보상기법 및 이에 대한 모의실험 결과를 소개하고자 한다.
This study tried to propose plan to prevent human error of railroad driver among human error of railroad worker which takes great share in railroad accident. For this, in order to maintain correlation between the accident actually occurred after the opening of high-speed railroad and experience of accident that did not happened, survey on respondent was analyzed by conducting survey on KTX captain who is working in driving work of high-speed railroad, and instruction management team manager who manages KTX captain and captain. This thesis classified the factors by human factor, job factor, environment factor, organization factor, and established human error management model by comparing and analyzing how each factors have spatial interrelations with a railroad accident. The purpose of this study is to contribute to make safe railroad, and reliable railroad by preventing human error accident by minimizing human error of high-speed railroad drivers, and improving driving workers to cope accurately and fast with irregularities through various institutional improvement, improvement of driving facilities, improvement of operating room environment, and improvement of education system.
A model experiment on the pair midwater trawl net applicable to 800 PS class Korean pair bottom trawlers was carried out in the special-prepared experimental thank. the tank was prepared as a reverse trapezoid shape in its vertical section by digging out flat soil. The dimension of the tank showed the 9.6 W$\times$43.0 L(m) of the upper fringe and the 4.8 W$\times$38.0 L(m) of the bottom with 3.0m in depth. The depth of water was maintained 2.7m during experiment. The model net was prepared based on the Tauti's similarity law of fishing gear in 1/30 scale considering the dimension of the experimental tank. Mouth performance of the model net during towing were determined by the photographs taken in front of the net mouth with the combinations of towing velocity, warp length and distance between paired boats. The results obtained can be summarized as follows: 1. Vertical opening of the model nets A and B was varied in the range of 0.18~0.88 m and 0.21~0.78 m (which can be converted into 5.4~26.4m and 6.3~23.4 m in the full-scale net) respectively, and was varied predominantly by towing speed. Vertical opening (H which is appendixed m for the model net. f for the full-scale net. A and B for the types of the model net) can be expressed as the function of towing velocity$V_t$as in the model net $V_t$ : m/ sec)$H_{mA}$=1.67$e^{-1.65V_t}$ $H_{mB}$=1.15$e^{-1.13V_t}$, in the full-scale net ($V_t$ : k't) $H_{fA}$=50.27$e^-0.37V_t$ $H_{fB}$=34.46$e^{-0.26Vt}$. 2. Horizontal opening of the model nets An and b was varied in the range of 1.03~1.54m and 1.04~1.55 m (which can be converted into 30.9~46.2 m and 31.2~46.5m in the full-scale net) respectively, and was varied predominantly by distance between paired boats. Horizontal opening (W, appendixes are as same as the former) an be expressed as the function of distance between paired boats $D_b$as in the model net $W_{mA}$=0.69+0.09$D_b$ $W{mB}$=0.73+0.09$D_b$, in the full-scale net $W_{fA}$=20.81+0.09$D_b$ $W_{fB}$=22.11+0.09$D_b$ 3. Net opening area of the model net A and B was varied in the range of 0.28~1.04 $m^2$ and 0.33~0.94$m^2$(which can be converted into 252~936$m^2$ and 297~846$m^2$ in the full-scale net) respectively, and was varied predominantly by towing velocity. Net opening area ($S$, appendixes are as same as the former) van be expressed as the function of towing velocity$V_t$ as in the model net $v_t$ : m/sec) $S_{Ma}$=2.01$e^{-1.54V_T}$ $S_{mA}$=1.40$e^{-1.65V_t}$, in the full-scale net ($V_t$ : k't) $S_{fA}$=1.807$e^-0.35V_t$ $S_{fA}$=1.265$e^{-0.24V_t}$. 4. Filtering volume of the model nets A and B was varied in the range of 0.32~0.55 $m^3$ and 0.37~0.55$m^3$(which can be converted into 8.640~14.850 $m^3$ and 9.990~14.850$m3$in the full~scale net) respectively, and was predominantly varied by towing speed. filtering volume of the model net-A showed the maximum at the towing speed 0.69 m/sec(3 k't in the full-scale net), compared with that of the model net B showed at 0.92 m/sec(4 k't in the full-scale net).
무부자 쌍끌이 중층망은 유속에 관계없이 뜸줄은 거의 일직선으로 유지되고 뜸줄의 깊이 변화가 없었다 또한, 뜸이 없기 때문에 부력은 작용하지 않지만 아래 끌줄의 길이를 조절함으로써 망고를 유지할 수 있었다. 그리고, 무부자 썽끌이 중층망의 전개성능은 발줄의 침자 외에도 추(Front weight)와 날개끝 추(Wing-end weight)의 침강력을 증가시킴으로써 더욱 향상될 수 있었다. 연구는 회류수조에서의 모형실험을 통하여 무부자쌍끌이 중층망의 추와 날개끝 추의 무게에 따른 전개 성능을 규명하고 그 결과를 기준형과 비교 분석하였다. 그 결과를 요약하면 다음과 같다. 1. 유체저항은 유속이 2.0∼5.0knot로 증가함에 따라 거의 직선적으로 증가하였으며, 느린 유속에서는 저항의 증가폭이 작지만, 유속이 빠를 때는 저항의 증가폭이 커지는 경향을 보였다. 추의 무게 및 날개끝 추의 무게의 증가함에 따라서도 유체저항은 증가 하였다. 2. 망고는 유속이 증가함에 따라 거의 직선적으로 감소하는 경향을 나타내었으며, 망고의 감소율은 기준형보다 무부자망이 낮았다. 추의 무게가 0.70ton 에서 1.75ton으로 증가할 때 각 단계별로 약 2m씩, 날개끝 추의 무게가 0.28ton에서 1.11ton으로 증가할 때 각 단계별로 약 1m씩 각각 망고가 증가하였다. 망폭은 기준형보다 모든 무부자망이 약 10m 정도 더 컸으며, 추와 날개끝 추의 무게가 증가햄에 따라 그 변화폭은 2m 내외로 거의 일정하였다. 3. 망구면적은 추의 무게가 1.75ton 일 때, 날개끝 추의 무게가 1.11ton일 때 최대가 되었고 유속이 2.0∼3.0knot에서는 무부자망이 기준형보다 작았으나, 4.0-5.0knot에서는 무부자망이 기준형보다 더컸다. 4. 여과량은 기준형에서는 3.0knot일 때, 무부자망에서는 4.0knot일 때 각각 최대가 되었으며, 추의 적정무게는 1.40ton이었다. 팀은 환자가 원하는 영적 간호를 실시하도록 체계적인 접근 방법을 강구해야 할 것으로 사료된다.된다. 통하여 움직임 감소 장치를 사용함으로써 내부 장기 중 횡격막 움직임의 범위가 감소함과 동시에 CTV-PTV 마진이 크게 줄어드는 결과를 확인하였다. 이 결과를 통하여 흉부 또는 복부에 종양을 가진 환자 치료 시 더욱 질 높은 방사선 치료가 실현될 것으로 기대한다. 30∼40% 정도 느렸고, 퍼레니얼라이그라스도 퍼레니얼라이그라스 100% 단일종류에 비해 20∼30%정도 늦었다. 따라서, 뗏장 재배시 여러 종류의 초종을 천편일률적으로 혼합하여 파종하는 것은 바람직하지 않으며, 컨셉에 따라 적절하게 초종 및 품종을 선택해서 사용하는 것이 필요하다. 5. 뗏장의 뿌리 형성 능력은 퍼레니얼라이그라스가 가장 좋았고, 가장 저조한 초종은 켄터키블루그라스였다. 톨훼스큐는 켄터키블루그라스와 퍼레니얼라이그라스의 중간정도로 나타났다. 혼합구의 뗏장 형성 능력은 초종의 혼합비에 따라 뿌리 형성력 차이가 다르게 나타났는데, 특히 퍼레니얼라이그라스 혼합비율이 많을수록 뿌리 형성 능력은 증가하였다. 6. 뗏장 수확시 잔디 품질은 단일 초종구의 품질이 혼합구에 비해 양호하였는데 가장 우수한 초종은 켄터키블루그라스였고, 톨훼스큐는 켄터키블루그라스 다음으로 중간정도, 그리고 퍼레니얼라이그라스는 가장 저조하였다. 켄터키블루그라스는 균일한 잔디 면, 고밀도 및 예초 후 상태가 우수한 특성으로 품질이 양호하였고, 퍼레니얼라이그라스의 품질이 저조하였던 것은 초장이 길어 잔디 면이 누운 상태로 나타나 균일도 저하 및 예초 후 품질이 켄터키블루그라스나 톨훼스큐 보다 떨어지기 때문이다. 그리고 혼합구의 품질은 여러 종류가 혼합됨으로 인해 색상 및 밀도의 균일도가 떨어지고, 또한 예초 시 물결처럼 불균일하게 깎여 잔디 표면이 불량하였기 때문이었다. 7. 골프장이나 경기장 기본 설계 시 초기 피복도 및 뿌리 형성력이
차량의 폭발적 증가로 인해 저속, 서행형태로 주행시간이 점점 늘어나므로, 본 연구에서는 연비향상을 목적으로 정차상태에서는 일부 실린더만으로 일정한 엔진회전수를 유지하고, 주행상태에서는 전 실린더를 이용하는 가변실린더에 대해 실제 하드웨어로 제작하여 실험해 보았다. 과거에 일부 제작되었던 가변실린더 엔진은 정차상태나 저속상태에서 사용하는 실린더 주위에 열이 집중하여 열응력이 발생하고, 사용하지 않는 실린더는 냉각수의 순환으로 인해 주변의 온도가 더욱 떨어지게 되어, 재점화시에 많은 유해가스가 배출되고 연료 소모량도 많아지게 되며, 엔진회전수가 고르지 못하는 문제가 있었다. 이러한 문제점을 극복하고자 정지상태나 저속주행상태에서와 같이 많은 출력을 요하지 않는 운행조건에서는 새로운 점화방식과 밸브 개폐시기를 이용하여 연비를 향상시키는 방안을 제시하고, 그 타당성을 검증하였다.
Infiltration characteristics of airborne particulate matter had been investigated in real-life for about 90 days over 2 years in a Korean apartment building where a 3-person household had lived and the exclusive private area was 84.9 ㎡. Airtightness was measured by fan depressurization, and the ACH50 was 2.41 times per hour. In and outdoor particle concentrations were measured by optical particle counters. Infiltration factors and filtration efficiencies of the house, which reflect the removal of outdoor particles penetrating building envelope and the deposition inside a building, were obtained from data screened based on an empirical evaluation process. Infiltration factor of fine particles showed a range from about 42% at 0.4 m/s of wind speed to 72% at 4.2 m/s of wind speed with closed windows and doors. Filtration efficiency was like a MERV 13 grade filter with an open window outside at a balcony at low outdoor wind speed under 1 m/s. The grade decreased to MERV 11 by opening another outside window at the other balcony. Filtration efficiencies decreased as much as 29% in average at a range of 0.3~2.5 ㎛.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.