• Water for future
• /
• v.27 no.4
• /
• pp.69-84
• /
• 1994

The aim of this paper is suggest how to control the real time reservoir operation for the optimal operation of reservoir during the draught and the rainy season. The realease and the storage lead to the achievement or the deviation losses, higher or lower than the target level. Considering this deviation as one of the losses, putting the penalty on the losses, the way of optimal reservoir operation is discussed in order to minimize the penalty losses. This study draw the deviation losses' curve depending on the operation objectie for the Daechung Dam, and apply the optimal operation to the Dam by the linear programing technique, using the slope of the deviation curve as the losses coefficience for the objective function. Conclusively, in this paper I can combine the opposing subjects -the release and the storage- as one objective function by the deviation curve, and also show how to decide the criterion relate to the real time reservoir operation by analysing to what extent and how easily the objectives can be achieved, subject to the inflows.

• Science of Emotion and Sensibility
• /
• v.21 no.2
• /
• pp.137-144
• /
• 2018

The study figured out the operational conditions of a two-way movement actuator made of one-way shape memory alloy (OWSMA) for versatile ventilation intelligent garments. To develop a low-power actuator that consumes energy only when a garment changes its form such as opening and closing, multiple channels of OWSMA were used, and optimum diameter of the wires was examined. For the switch device, optimum voltage application unit time was determined. Optimum diameter of OWSMA wire was determined by applying 3.7V to the pre-determined candidate diameters, which demonstrated two-way operation in previous studies. In order to evaluate the optimum voltage application time, the internal diameter of the actuator was measured while increasing and decreasing by 50 ms from the unit time of voltage application. Delay time under two-way operation of the actuator was measured to minimize interference caused by heat between channels. Power of 3.7V was applied to OWSMA for assessment of optimal time, and the whole process from heating to cooling was video-recorded with a thermal image camera to determine the point of time at which the temperature of OWSMA wire dropped below the phase transformation temperature. The results showed that $0.4{\Phi}$ was the most suitable diameter, and the optimum unit time of voltage applied to open and close the actuator was 4100ms. It was also shown that the delay time should be more than 1.8 seconds between two-way operations of the actuator.

• Journal of Internet Computing and Services
• /
• v.13 no.3
• /
• pp.93-105
• /
• 2012

A data stream is a series of tuples which are generated in real-time, incessant, immense, and volatile manner. As new information technologies are actively emerging, stream processing methods are being needed to efficiently handle data streams. Especially, finding out an efficient evaluation for a multi-way join would make outstanding contributions toward improving the performance of a data stream management system because a join operation is one of the most resource-consuming operators for evaluating queries. In this paper, in order to evaluate efficiently a multi-way join continuous query, we propose a novel method to decrease the cost of a query by eliminating unsuccessful intermediate results. For this, we propose a matrix-based structure for monitoring data streams and estimate the number of final result tuples of the query and find out unsuccessful tuples by matrix multiplication operations. And then using these information, we process efficiently a multi-way join continuous query by filtering out the unsuccessful tuples in advance before actual evaluation of the query.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.32 no.3
• /
• pp.477-486
• /
• 2022

This study aims to present a method using event sourcing patterns and blockchain as a way to cope with vulnerabilities in memory manipulation at the client level. To verify the plan, the method of running the memory operation application was analyzed, and the performance was compared and analyzed when the memory operation prevention plan was applied by fabricating a test application. As a result of the analysis, the usage of memory increased compared to the method of XOR operation by storing major data in one memory, but it was possible to prevent the operation of the memory operation program without significantly affecting the performance of the game.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.4
• /
• pp.47-53
• /
• 2007

A bearing is one of core parts in automobile. Rubber seal of the bearing is important to improve performance of bearing, formed by hot-press die of rubber seal for the intricate shape. In this study, formed tools are used to machine die of bearing rubber seal and the machining operation is classified into the several process of high precision. Design of experiments is used to optimize selection of the formed tools for the efficient machining of the hot-press die. The cutting force, tool wear and tool life are determined to characteristics. And, the clearance angle, the rake angle and the length cutting edge are considered as the major factors. Experiments are repeated to use one-way factorial design, and tool life is predicted by regression model.

• Korean Management Science Review
• /
• v.16 no.2
• /
• pp.13-32
• /
• 1999

Concurrent Engineering is one of the information-based product development approach. Yet, the method of organizing the project team for the concurrent engineering is not clear. This study focuses on deriving a method to organize an information-based project team. The model consists of 4 layers : IT infrastructure, organization of the information-based project team, operation of the project team, an organization culture. Based on an analysis of new product development case, this study attempts to verify the model and to suggest more effective way of organization design and management for new product development.

• Proceedings of the KSR Conference
• /
• 2002.10b
• /
• pp.937-942
• /
• 2002

As the subway composed of rolling stock, power supply, signalling, infrastructure is complex system, the optimization through standardization is one of the most effective way to reduce the cost of construction and operation. However, the subway in Korea has been built and operated in different kinds of system. In this paper, review for standardization of urban transit in Korea is executed and presented direction to standardization.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.7
• /
• pp.981-986
• /
• 2018

AC(alternating current) CB(circuit breaker) at the fault occurred in the existing AC distribution system is limiting the fault current through zero cross-point. However, DC(direct current) CB does not have zero cross-point. Therefore, arc occurred by on-off operation of DC CB is very huge. Nowadays, many research team are studying the way to decrease breaking time, which is one of the essential conditions in DC CB. We suggested novel arc-induction type DC CB in this paper. The proposed arc-induction type DC CB is composed of the mechanical Arc ring and DC CB. We confirmed the operation of arc-induction type DC CB through the HFSS(High Frequency Structure Simulator) 3D simulation program and performed the experiment for operation characteristics. Results showed that arcing time of the arc-induction type DC CB by using induction ring was faster than existing mechanical DC CB. On the transient system, we confirmed stable operation characteristics of the arc-induction type DC CB through the simulation and experimental results. We expect that the proposed arc-induction type DC CB technology is will go to stay ahead of the existing DC CB technology.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.12
• /
• pp.1163-1168
• /
• 2006

Manufacturing technology for the production of high value-added fine chemical products is emphasized and getting more attention as the diversified interests of customers and the demand of high quality products are getting bigger and bigger everyday. Thus, the development of advanced batch processes, which is the preferred and most appropriate way of producing these types of products, and the related technologies are becoming more important. Therefore, high-precision batch distillation is one of the important elements in the successful manufacturing of fine chemicals, and the importance of the process operation strategy with quality assurance cannot be overemphasized. Accordingly, proposing a process structure explanation and operation strategy of such processes including batch processes and batch distillation would be of great value. We investigate optimal operation strategy and production planning of multi-purpose plants consisting of batch processes and batch distillation for the manufacturing of fine chemical products. For the short-term scheduling of a sequential multi-purpose batch plant consisting of batch distillation under MPC and UIS policy, we proposed a MILP model based on a priori time slot allocation. Also, we consider that the waste product of being produced on batch distillation is recycled to the batch distillation unit for the saving of raw materials. The developed methodology will be especially useful for the design and optimal operations of multi-purpose and multiproduct plants that is suitable for fine chemical production.

• Journal of Korean Institute of Industrial Engineers
• /
• v.41 no.4
• /
• pp.330-337
• /
• 2015

A bucket-brigade is a way of transporting items where items are passed from one person to the next. The operation of the bucket brigade imitates the cooperative behavior of ants when brood, food or other resources are moved. Koo (2009) presented a bucket brigade-based assembly cell where each worker follows a simple rule: perform assembly operations on a product until the next worker downstream takes it over; then go back to the previous worker upstream to take over a new assembly job. In this way, the flow line is self-balanced without any predetermined job assignment. However, there are some productivity losses related to hand-off and blocking. This paper examines the hand-off and blocking losses and presents a new bucket brigade-based assembly cell where working areas for each assembler is restricted with the help of buffer interfaces. Simulation experiments are used to validate the performance of the new assembly system.