• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.579-580
• /
• 2006

Simple nonoverlapped source/drain-to-gate MOSFETs to suppress GIDL (gate-induced drain leakage) is simulated with SILVACO simulation tool. Changing spacer thickness for adjusting length of Drain to Gate nonoverlapped region, this simulation observes on/off characteristic of nonoverlapped source/drain-to-gate MOSFETs. Off current is dramatically decreased with S/D to gate nonoverlapped length increasing. The result shows that maximum on/off current ratio is achieved by adjusting nonoverlapped length.

• Journal of Electrical Engineering and Technology
• /
• 제9권5호
• /
• pp.1527-1536
• /
• 2014

This paper investigates the optimal values of turn-on and turn-off angles, and ratio of flux linkage at turn-off angle and peak phase current positions of optimal control for accomplishing maximum output power in an 8/6 Switched Reluctance Generator (8/6 SRG). Phase current waveform is analyzed to determine optimal excitation angles (optimal turn-on and turn-off angles) of the SRG for maximum output power which is applied from a nonlinear magnetization curve in terms of control variables (dc bus voltage, shaft speed, and excitation angles). The optimal excitation angles in single pulse mode of operation are proposed via the analytical model. Simulated and experimental results have verified the accuracy of the analytical model.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.190-190
• /
• 2007

To improved the conjugation between $SiO_2$ and P3HT active layer, P3HT/POSS conjugated polymers were synthesised and used as the active layers of organic TFT's. We achieved the field-effect mobilities in the saturation region ${\sim}1.19{\times}10^{-3}\;[cm^2/v{\cdot}sec]$ and on/off ratio ${\sim}2.51{\times}10^2$. These values are higher than ones of the P3HT-based OTFTs. The results also demonstrated the off-current decrease.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.1292-1294
• /
• 1993

This paper proposes a new structure of polycrystalline silicon(poly-Si) thin film transistor(TFT) having a thick gate-oxide below the gate edge. The new structure is fabricated by the gate re-oxidation in wet ambient. It is shown that the thick gate-oxide below the gate edge is effective in reducing the leakage current and the gate-drain overlap capacitance. We have simulated this device by using the SSUPREM4 process simulator and the SPISCES-2B device simulator. As a simulation result it is found that the new structure provides a low tentage current less than 0.2 pA and achieves a on/off ratio as high as $5{\times}10^7$.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.132.1-132.1
• /
• 2010

Anode off-gas of high temperature fuel cells such as MCFC still contain combustible components such as hydrogen, carbon monoxide and hydrocarbon. Thus, it's very important to fully burn anode off-gas and use the generated heat in order to increase system efficiency. In the present study, catalytic combustors have been applied to high temperature MCFC system so that the combustion of anode-off gas can be boosted up. Since the performance of catalytic combustor directly depends on the combustion catalyst, this study has been focused on the experimental investigation on the combustion characteristics of multiple commercial catalysts having different structures and compositions. In order to determine the design conditions of the catalytic combustor, parameters such as inlet temperature, space velocity and excess air ratio have been varied and optimized for combustor design. Results show that $H_2$ in off-gas assists $CH_4$ combustion in a way that it decreases minimum inlet temperature limit and increases maximum space velocity while keeping high fuel conversion efficiency.

• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.68-76
• /
• 2006

The minimization of maximum DPF wall temperature and the fast Light-off during regeneration are the targets for the high durability of the DPF system and the high efficiency of regeneration. In order to predict transient thermal response of DPF, one-channel numerical modeling has been adopted. The effect of the ratio of length to diameter(L/D), cell density, the amount of soot loading on temporal thermal response and regeneration characteristics has been numerically investigated under two different running conditions: city driving mode and high speed mode. The results indicate that the maximum wall temperature of DPF increase with increasing 'L/D' in 'High speed mode'. For 'City driving mode', the maximum wall temperature decreases with increasing 'L/D' in the range of $'L/D{\geq}0.6'$. The maximum temperature decreases with increasing cell density because heat conduction and heat capacity are increased. It is also found that the effect of amount of soot loading on light-off time is negligible.

• 한국전기전자재료학회논문지
• /
• 제24권7호
• /
• pp.525-531
• /
• 2011

In this paper, experimental analyses have been performed to compare the electrical characteristics of n channel LT(low temperature) and HT(high temperature) poly-Si TFTs(polycrystalline silicon thin film transistors) on quartz substrate according to activated step annealing. The size of the particles step annealed at low temperature are bigger than high temperature poly-Si TFTs and measurements show that the electric characteristics those are transconductance, threshold voltage, electric effective mobility, on and off current of step annealed at LT poly-Si TFTs are high more than HT poly-Si TFT's. Especially we can estimated the defect in the activated grade poly crystalline silicon and the grain boundary of LT poly-Si TFT have more high than HT poly-Si TFT's due to high off electric current. Even though the size of particles of step annealed at low temperature, the electrical characteristics of LT poly-Si TFTs were investigated deterioration phenomena that is decrease on/off current ratio depend on high off current due to defects in active silicon layer.

• 사상체질의학회지
• /
• 제34권4호
• /
• pp.27-37
• /
• 2022

Objectives The purpose of this study is to propose a method to more specifically identify Sasang constitutional risk factors of metabolic syndromes by adjusting the cut-off value of Korea Sasang Constitutional Diagnostic Questionnaire (KS-15). Methods Data of 1997 participants in Korean medicine Daejeon Citizen Cohort study (KDCC) were analyzed. Metabolic syndrome was defined according to the NCEP-ATP III, lifestyle information, and hematologic information including KS-15 and demographic characteristics were used as covariates. Results The 179 subjects with metabolic syndrome accounted for 9.0% of the total. As a result of determining the Sasang constitution for the KS-15 response based on the cut-off values (approximate 0.33), 0.5, and 0.6 of the constitutional score, when performed at the 0.6 cut-off model, the odds ratio of TE was 2.46 which showed a statistically significantly higher risk than the borderline group. For the accuracy of the model and the Area under the curve (AUC), the model accuracy based on the original cut-off of the KS-15 was 0.902 and AUC was 0.737. The accuracy of the model with cut-off of 0.5 and with of 0.6 were 0.904 and 0.902, respectively, and the AUCs were 0.687 and 0.741, respectively. Conclusion In this study, we confirmed that it is effective to increase the cut-off value of KS-15 to 0.6 in the metabolic syndrome risk model. It is expected that this could increase the accuracy of identifying high-risk groups for metabolic syndrome.

• 한국세라믹학회지
• /
• 제32권1호
• /
• pp.131-139
• /
• 1995

In order to improve transmittance and response properties, various compositions of light controllable films were prepared by phase separation method. The optical and response properties were measured with the variation of PMMA/suspension ratio and block copolymer/light polarizing particles. According to the increase of the PMMA/suspension ratio, the separated droplets of suspension were interconnected in the film. Decay time was 2.6 sec when PMMA/suspension ratio was 0.5 : 1 and ΔT(difference of the transmittance at OFF/ON states) was reduced with increasing of the ratio of PMMA/suspension. On block copolymer/light polarizing particles ratio variation, the highest transmittance of the film was 67.4% when its ratio was 0.6 : 1 and decay time was varied from 2.15 to 46.6 sec as block copolymer content increased 0.2 : 1 to 1 : 1.

• 에너지공학
• /
• 제21권4호
• /
• pp.411-418
• /
• 2012

본 연구에서는 가솔린 엔진 자동차의 엔진 폐열 회수를 위한 이중 회로 랭킨 사이클 시스템에서 용적형 팽창기의 설계 팽창비에 따른 성능 해석이 수행되었다. 자동차 엔진 폐열 이용 랭킨 사이클 시스템에 사용되는 용적형 팽창기는 운전 조건에 따라 설계 팽창비가 운전 압력비보다 낮은 저팽창 조건과 설계 팽창비가 운전 압력비보다 높은 과팽창 조건으로 운전되므로 탈설계 조건에서 성능 예측이 중요하다. 또한 용적형 팽창기는 자동차 적용시 팽창효율 뿐만 아니라 부피와 무게를 최소화하는 것이 매우 중요하므로 이를 고려한 설계 팽창비의 최적화가 요구된다. 본 연구에서는 용적형 팽창기의 탈설계 조건에서 성능 예측을 통해 팽창효율과 팽창기의 용적을 동시에 고려하여 설계 팽창비를 목표 운전 압력비보다 낮도록 하여 저팽창 운전을 하도록 설계 하는 것이 유리함을 제시하였다.