• 한국자동차공학회논문집
• /
• 제12권3호
• /
• pp.37-43
• /
• 2004

Engine lubrication system is generally affected by vehicle driving conditions; acceleration, braking deceleration, and cornering. The oil supply system such as oil pan, baffle plate, and oil pick-up pipe should be optimized to cope with severe driving conditions. The main purpose of this paper is to understand the effect of the engine tilting angle on the oil supply system using engine tilting test rig. For the purpose, the oil pressure fluctuation and oil aeration in the main gallery are measured at various engine tilting angles. In addition, the oil flow is visualized by using transparent oil pan to investigate the cause of the formation of oil aeration. The test results show there is a strong correlation between the main gallery oil pressure fluctuation and oil aeration. It is also found that the visualization technique is helpful to stabilize the oil supply system at severe driving conditions.

• Tribology and Lubricants
• /
• 제20권1호
• /
• pp.27-32
• /
• 2004

This paper presents unsteady oil flow behaviors in the engine lubrication network to clarify the differences between continuous and discontinuous oil supply crankshaft system. Using commercial network analysis program, Flowmaster2, engine lubrication network system analysis were carried out. And effects of crankshaft speed and supplied oil pressure on pressure fluctuation in oil groove and oil flow rate to each bearing were analyzed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1258-1261
• /
• 2003

Oil supply system is one of the most important part of Turbine. Lubricating oil of bearings supplied by oil pump. Failure of Oil supply pump critical damaged parts of Turbine, especially bearings. In this paper we have discussed the serious damage of turbine bearings due to failure of Oil supply pump.

• 동력기계공학회지
• /
• 제9권4호
• /
• pp.24-30
• /
• 2005

For a reciprocating compressor of household refrigerators, a direct analogy between the pipe flow network and the electric circuit network has been utilized to set up a mathematical model for oil supply system. Individual lubrication elements of the oil supply system, such as propeller- installed oil cap, oil galleries, radial oil feeding holes, spiral oil grooves, and various sliding surfaces have been analogized by equivalent electric elements, and these have been combined together to form an electric circuit corresponding to the whole oil supply system. By solving the closed network equations of the model, oil flow rates at various lubrication elements could be obtained. Total amount of the oil flow rate drawn into the shaft has been measured and compared reasonably well with the prediction of the numerical simulation.

• 한국정밀공학회지
• /
• 제21권2호
• /
• pp.108-115
• /
• 2004

Experiment and analytical studies on the oil supply characteristics of scroll compressor have been presented. For a scroll compressor, oil supply system consisting of individual lubricating element such as pumps, oil passages and sliding surfaces has been modeled by equivalent electric circuit. By solving the closed network equations of the model, oil flow rates at various lubrication elements could be obtained. Total amount of the oil flow rate drawn into the shaft has been measured and compared reasonably well with the prediction by the numerical simulation.

• 한국자동차공학회논문집
• /
• 제10권3호
• /
• pp.44-50
• /
• 2002

The connecting rod big-end bearing is one of the most heavily loaded components of the lubrication system of high-speed combustion engines. The supply oil flow has to pass to the main bearing and the rotating crankshaft before entering the connecting rod bearing. It is common knowledge that the centrifugal forces due to the crankshaft rotation influence the oil flow to connecting rod bearing through the oil supply bore, especially, when the oil supply system to the connecting rod bearing has a 180$^{\circ}$circumferential groove via a single drilling in the crankshaft. In this case, it should be confirmed that the groove oil pressure in the main bearing is sufficient to overcome these centrifugal forces. For the purpose, the dynamic oil pressure before entering oil supply bore to the connecting rod bearing was measured instead of averaged oil pressure in main gallery. Experimental test results show that the dynamic oil pressure in the oil groove was more useful than that of main gallery. And it was also found that the oil pressure fluctuation in the groove was sensitively affected by the reduction of the main bearing clearance.

• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.90-95
• /
• 2004

In this study, for the crankshaft bearing design adapting discontinuous oil supply system, analyses were conducted to determine the lubrication characteristics such as oil flow rate and increase of oil temperature at main bearing and connecting rod bearing. Additionally, supplied oil pressure and temperature effects on the bearings were simulated to figure out lubrication characteristics on the bearings. Finally the effects of increasing the bearing width and clearance were introduced on the lubrication characteristics.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 동계학술발표대회 논문집
• /
• pp.113-118
• /
• 2008

For a R134a rotary vane compressor used for car air conditioners, characteristics of gas compression and oil supply have been studied. The compressor model under investigation has the low volume ratio of suction to discharge volumes so that there occur flow reversal from discharge port to compression chamber as the leading vane passes over the discharge port. As a result, the volumetric and adiabatic efficiencies turn out to be relatively low compared to other types of displacement compressors. Oil supply mechanism has been comprehended for mathematical modeling and oil flow rate has been calculated for the individual oil passages. This study on the gas compression and oil supply of a rotary vane compressor can be applied to a future design practice on a similar type of compressor.

• 한국자동차공학회논문집
• /
• 제19권5호
• /
• pp.51-57
• /
• 2011

Parametric studies based on analysis of lubrication system of a four cylinder gasoline engine are illustrated system in this paper. In development process of engine lubrication system, parts of failure cases are related with oil pull over and oil churning phenomenon. The crankcase & head system pressure by oil churning phenomenon are gradual increased. It cause oil pull over phenomenon at engine breather line and oil over-consumption. In order to improve oil reduction and oil pull over phenomenon are also considered in the developing state. For this study, the characteristics of engine lubrication system are measured at various tilting angle and drain hole sizes. In addition, the oil flow & oil quantity are tested by blow by meter and catch jar. Results are presented to stabilize the oil supply system at sever driving condition. The data from present study are available for the engine lubrication system.

• 수산경영론집
• /
• 제31권1호
• /
• pp.115-133
• /
• 2000

The policy of suppling tax-exempt fishery oil in Korea has a history of almost 40 years, which was initiated by the National Federation of Fisheries Cooperatives in 1965. In 1999 the volume of fishery oil supplied to the earning fishermen and fishing entrepreneurs amounted to 8,390 thousand DM, 500 billion won in total. This paper analyzes the oil supplying system to fishermen in Korea and shows that the structural obstacles to the stable provision of fishery oil lies in the ineffective bargaining power (fixing price). Provided that the NFFC as a buyer, which is not equipped with the storage facilities for oil bids for a unit-price contract of fishery oil, there exists a possibility of collusion among 5 local oil refineries corporations to influence the oil price, making it difficult to reach a resonable price of oil. Though the international bids and direct imports following the liberalization of oil imports would help lower the unit price, purchasing and importing the oil out of season at a lower price would not be guaranteed without the oil storage facilities. Furthermore, the current supply system of oil is quite vulnerable to the extraneous factors and, say when the oil price soars unpredictably, it is almost impossible to supply low - priced fishery oil to fishermen. The National Federation of Fisheries Association of Japan(Zengyoren), for instance, possesses 10 oil storage facilities, which had been built across the country during the last 20 years (1964-1984). The storage capacity of these facilities reaches 0.6million DM(by kind, 0.56million DM for A heavy oil, 38thousand D/M kerosene, 5thousand D/M for diesel fuel oil). Allowing no intermediary of production associations(fisheries cooperatives) the NFFA's capacity for keeping oil in reserve rises much higher. As these storage facilities can keep the oil amounting to as much as of 70 days demand in reserve, a stable supply of fishery oil on favorable terms is secured. In contrast with Japan case, unequipped with the storage facilities for fishery oil, Korea does not have much bargaining power for bringing down the price of fishery oil. To make matters worse, the oil storing capacity of the member cooperatives is the volume of only 8 days demand. In case the oil price rises, it is almost impossible to supply the oil to the fishermen at a price lower than the price risen.