• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.6
• /
• pp.30-37
• /
• 1989

The PIN type a-SiC:H/a-Si:H heterojunction solar cells were fabricated by using the rf glow discharge decomposition of $SiH_4$ mixed with $CH_4,B_2,H_6\;and\;PH_3.$ The efficiency of the solar cell of the $SnO_2/ITO$ was higher than that of ITO transparent oxide layer by 1.5%. The P layer was prepared with the thickness of $100{\AA}$ and $CH_4/SiH_4$ ration of 5. The I layer has been deposited on the P layer and it is not pure intrinsic but near N type. So $SiH_4$ mixed with $B_2H_6$ of 0.3ppm was used to change this N type nature to intrinsic having the thickness of 5000${\AA}$. And consecutively, the N layer was deposited with t ethickness of $400{\AA}$ using $SiH_4/PH_3$ mixtures. The solar cell demonstrated 0.94V of $V_{oc'}$ 14.6mA/cm of $J_{sc}$ and 58.2% of FF, resulting the efficiency of 8.0%. To minimize loss by the reflection of light, $MgF_2$ layer was coated on the lgass and the efficiency was improved by 0.5%. Therefore, the solar cell indicated overall efficiency of 8.5%.

• Korean journal of applied entomology
• /
• v.48 no.1
• /
• pp.67-72
• /
• 2009

The kairomonal activity of the aggregation pheromones of Riptortus clavatus for the egg parasitoid, Gryon japonicum, were investigated in soybean field. The parasitism rate of G. japonicum gradually decreased when the distances between pheromone traps and egg sites were increased from 0 to 15 m. The active distance of pheromone source for parasitoid attraction was estimated to be ca. 15 m. Under field conditions, the parasitoid wasp population peaked during the late August and early September, and the parasitism rate increased when the number of pheromone traps was increased from one to three per $165\;m^2$. However, insecticide-treated plots, the level of parasitism recorded is relatively low. Sex ratios in field populations of G. japonicum were female-biased.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.7
• /
• pp.829-835
• /
• 2010

This paper presents a disposable power generator for microfluidic devices; the power generator has a tubular PEMFC and a $H_2$ generator. The tubular PEMFC has a tubular MEA (diameter: 1.52 mm) that is supported by a spiral wire electrode. The $H_2$ generator supplied $H_2$ to the tubular PEMFC; $H_2$ was generated via the reaction of Al foil (27 mg) and 5 M NaOH (0.12 ml). The open circuit voltage and power density of a unit cell of the tubular PEMFC were 0.81 V and $16.4\;mW/cm^2$ (0.35 V), respectively. The $H_2$ generator generated 11.6 ml $H_2$ for 15min. The power generator was continuously operated for 15 min at 0.64 mW (0.71 V) and for 10 min at 1.06 mW (0.46 V). We experimentally verified that it is feasible to use the proposed power generator as a power source for microfluidic devices; in the experiment, an LED (2.5 mW; 1.8 V) was lit for 10 min by using three serially connected TPEMFCs and one $H_2$ generator.

• Applied Chemistry for Engineering
• /
• v.29 no.1
• /
• pp.103-111
• /
• 2018

A plasma-catalytic combined process was used as an attempt to improve the conversion efficiency of nitrogen oxides ($NO_x$) over a wide temperature range ($150{\sim}500^{\circ}C$) to cope with the exhaust gas whose temperature varies greatly. Since the catalytic $NO_x$ reduction is effective at high temperatures where the activity of the catalyst itself is high, the $NO_x$ reduction was carried out without plasma generation in the high temperature region. On the other hand, in the low temperature region, the plasma was created in the catalyst bed to make up for the decreased catalytic activity, thereby increasing the $NO_x$ conversion efficiency. Effects of the types of catalysts, the reaction temperature, the concentration of the reducing agent (n-heptane), and the energy density on $NO_x$ conversion efficiency were examined. As a result of comparative analysis of various catalysts, the catalytic $NO_x$ conversion efficiency in the high temperature region was the highest in the case of the $Ag-Zn/{\gamma}-Al_2O_3$ catalyst of more than 90%. In the low temperature region, $NO_x$ was hardly removed by the hydrocarbon selective reduction process, but when the plasma was generated in the catalyst bed, the $NO_x$ conversion sharply increased to about 90%. The $NO_x$ conversion can be maintained high at temperatures of $150{\sim}500^{\circ}C$ by the combination of plasma in accordance with the temperature change of the exhaust gas.

• Korean Journal of Food Science and Technology
• /
• v.25 no.1
• /
• pp.1-8
• /
• 1993

Extruded defatted soy flour (DSF) with twin screw extruder was compared with steam treated DSF for soy sauce fermentation. Independent variables of response surface methodology (RSM) for extrusion were barrel temperature $(145{\sim}165^{\circ}C)$, feed moisture content $(25{\sim}35%)$, and feed rate $(20{\sim}30\;kg/hr)$. Extrusion conditions for production of the extrudates having highest water absorption capacity, lowest bulk density and highest expansion ratio were obtained by regression analysis of each dependent variable. Electron photomicrographs revealed significant increase of porosity inside the koji made from extruded DSF. Therefore, growth of fungi inside the koji made from extrudates of DSF was accelerated to achieve higher activities of protease, ${\alpha}-amylase$, and glucoamylase compared to the koji made from steamed DSF. Although amino acid composition of soy sauces prepared from two different DSF did not show any significant difference, the content of free amino acids in soluble nitrogen compounds was higher $(13%{\pm}2)$ in soy sauce made from extruded SDF. During the whole period of fermentation color of soy sauce made from extrudates of DSF was darker. Sensory evaluation did not reveal any serious off-odor and off-taste in the soy sauce fermented from extruded DSF.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.3 s.345
• /
• pp.49-58
• /
• 2006

In this paper, a curve-fitting channel estimation method is proposed for orthogonal frequency division multiplexing (OFDM) system in a time-varying frequency-selective fading channel. The method can greatly improve channel state information (CSI) estimation accuracy by performing smoothing and interpolation through consecutive curve-fitting processes in both time domain and frequency domain. It first evaluates least-squares (LS) estimates using pilot symbols and then the estimates are approximated to a polynomial with proper degree in the LS error sense, starting from one preferred domain in which pilots we densely distributed. Smoothing, interpolation, and prediction are performed subsequently to obtain CSI estimates for data transmission. The channel estimation processes are completed by smoothing and interpolating CSI estimates in the other domain once again using the channel estimates obtained in one domain. The performance of proposed method is influenced heavily on the time variation and frequency selectivity of channel and pilot arrangement. Hence, a proper degree of polynomial and an optimum approximation interval according to various system and channel conditions are required for curve-fitting. From extensive simulation results in various channel environments, we see that the proposed method performs better than the conventional methods including the optimal Wiener filtering method, in terms of the mean square error (MSE) and bit error rate (BER).

• Korean Journal of Weed Science
• /
• v.32 no.3
• /
• pp.188-194
• /
• 2012

Field experiments were conducted to investigate the competition relationships of main paddy weeds with transplanted rice grown in paddy conditions. Data were used to predict crop yield as a function of weed density using a rectangular hyperbola model and determine weed economic threshold (ET) levels. The rectangular hyperbola (equation 2) was fitted to rice yield to estimate weed-free rice yield ($Y_o$) and weed competitivity (${\beta}$). Its competitivity for M. vaginalis was 0.0007445, 0.0005713, 0.000988 and 0.0008846 in Daejeon, Suwon, Iksan and Naju, respectively. The competitivity at harvest represented by parameter ${\beta}$ ranged from 0.001611 in Naju to 0.002437 in Iksan for S. trifolia. The ET levels of main paddy weeds in machine transplanted rice cultivation were well estimated based on the herbicides applied and its application cost. Therefore, our results can be used to support decision-making on herbicide application for weed management in transplanted rice cultivation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.10
• /
• pp.788-795
• /
• 2013

A magnesium bipolar plate whose surface was protected by thinly deposited silver layer was investigated as an alternative to existing graphite bipolar plate of PEM fuel cells. Thin silver layer of $3{\mu}m$ was deposited on a magnesium alloy substrate by physical vapor deposition (PVD) method in an environment of $180^{\circ}C$. A number of tests were conducted on the fabricated magnesium based bipolar plates to determine their suitability for use in PEM fuel cell stacks. The test on corrosion resistance in the same pH condition as in a PEM operation demonstrated the layer protected the magnesium alloy substrate, while unprotected substrate suffered from severe corrosion. The contact resistance of the fabricated bipolar plate was less than $20m{\Omega}-cm^2$ which was superior to the conventional bipolar plates. A single cell was constructed using the fabricated bipolar plates and power output was measured. Due to the enhanced conductivity caused by low contact resistance, slight increase was observed in current density and output voltage. With low density of the magnesium substrate and ease on machining, the weight reduction of the stack of 30~40 % is possible to produce the same power output.

• The KIPS Transactions:PartA
• /
• v.17A no.6
• /
• pp.265-274
• /
• 2010

As the process technology scales down and integration densities continue to increase, interconnection has become one of the most important factors in performance of recent multi-core processors. Recently, to reduce the delay due to interconnection, 3D architecture has been adopted in designing multi-core processors. In 3D multi-core processors, multiple cores are stacked vertically and each core on different layers are connected by direct vertical TSVs(through-silicon vias). Compared to 2D multi-core architecture, 3D multi-core architecture reduces wire length significantly, leading to decreased interconnection delay and lower power consumption. Despite the benefits mentioned above, 3D design technique cannot be practical without proper solutions for hotspots due to high temperature. In this paper, we propose three floorplan schemes for reducing the peak temperature in 3D multi-core processors. According to our simulation results, the proposed floorplan schemes are expected to mitigate the thermal problems of 3D multi-core processors efficiently, resulting in improved reliability. Moreover, processor performance improves by reducing the performance degradation due to DTM techniques. Power consumption also can be reduced by decreased temperature and reduced execution time.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.167-175
• /
• 2019

Recently, health examination centers have been changing from auxiliary medical facilities to key and independent medical facilities. However, it is not easy to improve medical facilities, including health examination centers, due to the variable characteristics of the relationship between humans and space. Therefore, this study was done to develop a pedestrian-based discrete event simulation analysis program to examine the problems and develop methods for improvement. The program was developed to analyze five evaluation indices and the density of examinees. The problems were derived by analyzing the required time, capacity, and queue size for each examination through simulations. We reduced the examination time and moving distance, increased the capacity, and distributed the queues by adjusting the medical services and relocating the examination rooms. The results were then quantitatively verified by simulations.