• Journal of the Korean Society for Nondestructive Testing
• /
• v.11 no.1
• /
• pp.13-22
• /
• 1991

In this paper, 3-dimensional fracture phenomena in the local area near a through notch tip located between the surface and the canter were investigated by using embedded dyeing grids with the pitch of $50.8{\mu}$. It was confirmed that displacement V and square root of distance from notch tip $y^{1/2}$ are not proportional in the local area of $\sqrt{{\mid}y{\mid}}\;<\;0.3mm^{1/2}$ and the maximum shea strain ${\varepsilon}_{xymax}$ near a notch tip occurred at the curvature beginning point of the notch curve. It was also noted that the maximum strain ${\varepsilon}_{xymax}$ in the thickness direction occurred at the interior, where the ratio of the distance measured from surface to the half of thickness of specimen is 0.3.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.6
• /
• pp.916-922
• /
• 1986

This paper presents the preliminary results of an experimental study on surface crack growth under fatigue loadings. The objective of this paper is to assess the effect of the initial crack size on crack propagation behaviors. Transparent PMMA plate speciments with shallow circular arc notch were used. Crack growth behaviors were observed and measured in two directions by travelling microscopes. The fatigue crack initiated at the deepest part on the initial arc shaped notch and then propagated to depth direction as well as spreading gradually along the notch tip. A considerable number of cycles was needed until the depth crack spreaded to the surface notch tip. When the fatigue crack reached the surface notch tip the crack front became an approximate semi-ellipse, primary semi-elliptical crack. Test results suggest that the relationships between fatigue crack growth rate and stress intensity factor range in both directions can be expressed by power law (Paris) and that relationship in width direction depends upon the crack ratios a$_{1}$/b$_{1}$, of the primary semi-elliptical crack. The relationship between the nondimensional crack lengths in both directions can be represented as the formula: (a/t)$^{n}$ =B(2b/W+A) where n and A are constants and B is seems to be depended upon the crack ratio a$_{1}$/b$_{1}$.

• Journal of the Korean Institute of Gas
• /
• v.27 no.2
• /
• pp.95-103
• /
• 2023

In this paper, in order to evaluate the deformation characteristics of the hydrogen gas storage vessel(Type 1) when considering gas pressure, the VMS generated in the hydrogen gas storage vessel according to the notch shape of ISO 18119 was interpreted as a FEM(Finite Element Method). According to the analysis results, the maximum VMS generated in the longitudinal notch was higher than the transverse notch. In addition, the stress of the storage vessel was analyzed by the stress ratio, which is the yield strength ratio of the material to the VMS generated. According to the analysis results, in the case of a storage vessel with a notch formed in the longitudinal direction, the inside and outside of the storage vessel increased to 0.85 and 0.50 at a gas pressure of 50 MPa, respectively, but were analyzed to be lower than 1.

• Journal of Welding and Joining
• /
• v.2 no.1
• /
• pp.41-48
• /
• 1984

Recrystallization technique was applied to analyze plastic strain at the notch tip of coarse grain HAZ in mild steel (SB 41) and high strength steel (SA 588). The notch tip of specimen was deformed by three point bending. Accumulated displacement (Crack Opening Displacement ${delta}t$) by the monotonic and cyclic loading under room temperature and hot strain embrittlement temperature ($250^{\circ}C$) was 0~1.0mm. Recrystallization heat treatment conditions were $650^{circ}C{ imes}3hr$ for SB 41 and $700^{circ}C{ imes}3hr$ for SA 588. The experimental results obtained were as follows ; 1) Distribution of the effective plastic strain at plastic zone was appeared by the function of crack opening displacement, and plastic zone or the effective plastic strain increased with crack opening displacement. 2) Plastic strain at notch tip of HAZ due to accumulated hot strain calculated as follows. .epsilon. over bar $_{p}$ = .epsilon. over bar $_{cr}$ (x/ $R_{x}$ ) $^{m}$ (m=0.25) 3) Work hardending ratio of notch tip for hot strain was linearly increased with .epsilon. over bar $_{max}$ and dependent upon the material types.s.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.7
• /
• pp.11-19
• /
• 2003

In this study, unsaturated polyester resin, artificial lightweight coarse aggregate, artificial lightweight fine aggregate, heavy calcium carbonate and steel fiber were used to produce a steel fiber-reinforced lightweight polymer concrete with which mechanical properties were examined. Results of this experimental study showed that the flexural strength of unnotched steel fiber-reinforced lightweight polymer concrete increased from 8.61 to 13.96 MPa when mixing ratio of fiber content increased from 0 to 1.5%. Stress intensity factors($K_{IC}$) increased with increasing fiber content ratio while it did not increase with increasing notch ratio. Energy release rate ($G_{IC}$) turned out to depend upon the notch size, and it increased with increasing steel fiber content.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.4
• /
• pp.719-726
• /
• 1987

In this paper, an adaptive IIR (infinite impulse response) notch filter of lattice type is constructed and its adaptation algorithm is proposed for the detection and retrieval of a sine wave signal embedded in noise. A modified method which adapts only one coefficient of the filter is also suggested. All these methods adapt the coefficients while keepting the poles of the filter inside the unit circle on z-plane, and thus they satisfy the condition on the stability of the IIR filter after it has converged. To investigate the convergence characteristics of these methods such as convergence speed and output S/N ratio, intensive computer simulation has been performed by varying the frequency of the sine wave and the input S/N ratio. And the results of the simulation have been compared to those of Rao and Kung's which shows relatively fast convergence speed. The methods proposed here, especially the second one. shows faster convergence speed and higher output S/N ratio than the Rao and Kung's.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.5
• /
• pp.463-468
• /
• 2009

Torsional oscillations of the drivetrain in electric vehicles are generated under rapid driving conditions. These lead to an uncomfortable jerking of the vehicle and an increased stress of the mechanical components. To suppress torsional oscillations, the low pass and notch filters between the torque command from the acceleration pedal and electric motor input torque are suggested. The filter parameters are optimized based on Taguchi method with $L_{18}(3^5)$ orthogonal array. The signal to noise (S/N) ratio mainly depends on slew rate of motor input torque, damping ratio and natural frequency of notch filter. With the proposed suppression control scheme, the S/N ratio is shown to be increased by 4.7dB and the torque overshoot of the drive shaft is reduced to 30%.

• Molecular & Cellular Toxicology
• /
• v.5 no.2
• /
• pp.160-164
• /
• 2009

Notch signaling plays a crucial role in development of the nervous system. Neurodevelopmental hypothesis on etiology of schizophrenia has been implicated. The aim of this study is to determine whether single nucleotide polymorphisms (SNPs) of Notch homolog 4 (Drosophila) (NOTCH4) gene are associated with schizophrenia. This study included 283 schizophrenia patients diagnosed according to DSM-IV and 301 normal control subjects. Control subjects without history of psychiatric disorders were recruited. Four missense SNPs [rs915894 (exon 3, Lys117Gln), rs2071282 (exon 4, Pro204Leu), rs422951 (exon 6, Thr320Ala), and rs17604492 (exon 18, Gly942Arg)] of NOTCH4 gene were genotyped by the direct sequencing method. Multiple logistic regression models (codominant, dominant, and recessive models) were employed to evaluate odds ratio, 95% confidence interval, and p value. For analysis of genetic data, SNPStats, Haploview, HapAnalyzer, SNPAnalyzer, and Helixtree programs were also used. Of 4 SNPs, rs2071282 was weekly associated with schizophrenia in two alternative models (codominant model, P=0.049; dominant, P=0.041). However, these associations were not significant after Bonferroni correction. At 4 SNPs, one linkage disequilibrium (LD) block was made. This block consisted of rs915894 and rs2071282. In haplotype analysis, AC haplotype was weakly associated with schizophrenia (dominant, P=0.04). This association was disappeared after Bonferroni correction. Our result shows possibility that some SNPs of NOTCH4 gene may be weekly associated with development of schizophrenia in Korean population. However, replication result by other population will be needed.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.893-896
• /
• 2005

This paper describes Low Noise Amplifier(LNA) and Single Balanced Mixer(SBM) with monolithic image rejection notch filter using 0.5um MESFET process. LNA, Notch filter, and SBM were integrated on a chip. This chip does not need off chip SAW filter, thereby reducing the overall cost and system volume. The LNA with Notch filter provides a gain of 15dB, noise figure of 1.2dB, and image rejection ratio of -74dB. The SBM has a conversion gain of 6dB.

• Structural Engineering and Mechanics
• /
• v.74 no.5
• /
• pp.601-609
• /
• 2020

In this article, the Strain Energy Density (SED) averaged over a well-defined control volume at a notch edge was applied in combination with the Equivalent Material Concept (EMC) to assess the fracture behaviors of some keyhole-notched specimens made of a High-Density Polyethylene (HDPE-PE80) material under mixed-mode loading conditions. An experimental program was performed and 54 new experimental data were totally provided. Additionally, different loading mode ratios were regarded by changing the inclination angles of the notches with respect to the applied load directions. The results obtained from the determined criteria were in good agreement with those of the experimental data.