• 한국통계학회:학술대회논문집
• /
• 한국통계학회 2005년도 춘계 학술발표회 논문집
• /
• pp.191-196
• /
• 2005

Knowing the time of the process change could lead to quicker identification of the responsible special cause and less process down time, and it could help to reduce the probability of incorrectly identifying the special cause. In this paper, we propose a MLE of the process change point when control charts with the fixed sampling rate (FSR) scheme or the variable sampling rate (VSR) scheme monitor a process to detect changes in the process mean and/or variance of a normal quality variable.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제16권2호
• /
• pp.104-109
• /
• 2016

Purpose: The purpose of this study is to analyze fracture behavior and failure mechanism of porous titanium for dental implant fabricated by space holder process. Method: Three porous titanium specimens with a specific volume fraction of open pore were test by 3 point bending and compression stress condition, respectively. Fracture appearance was observed by scanning electron microscope and discussed in relation with oxygen content. Results: For compression-tested specimens, two specimen showed brittle failure, while the other one showed normal failure after deformation. High oxygen content was detected in the brittle-fractured specimen. Several micro-cracks initiated at the struts propagated down to the bottom of the specimen resulting in normal failure. Conclusion: Oxygen contamination during the fabrication process can leads brittle premature failure, and hence quality problem of the porous titanium for dental implant.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1352-1355
• /
• 1996

The control of diamond turning is usually achieved through a laser-interferometer feedback of slide position. If the tool post is rigid and the material removal process is relatively static, then such a non-collocated position feedback control scheme may surface. However, as the accuracy requirement gets tighter and desired surface contours become more complex, the need for a direct tool-tip sensing becomes inevitable. The physical constraints of the machining process prohibit any reasonable implementation of a tool-tip motion measurement. It is proposed that the measured force normal to the face of the workpiece can be filtered through an appropriate admittance transfer function to result in the estimated depth of cut. This can be compared to the desired depth of cut to generate the adjustment control action in addition to position feedback control. In this work, the design methodology on the admittance model-based control with a conventional controller is presented. The recursive least-squares algorithm with forgetting factor is proposed to identify the parameters and update the cutting process in real time. The normal cutting forces are measured to identify the cutting dynamics in the real diamond turning process using the precision dynamometer. Based on the parameter estimation of cutting dynamics and the admittance model-based nanodynamic control scheme, simulation results are shown.

• 한국임상수의학회지
• /
• 제25권6호
• /
• pp.537-539
• /
• 2008

A 6 month-old male Labrador retriever was presented for intermittent lameness on the left forelimb after exercise. The dog was suffering progressive lameness that had started two months before. On mediolateral radiographic view of the left elbow, proximal margin of the anconeal process was irregular. A lucent, indistinct line separating the anconeal process from the ulna was observed, when the elbow joint was flexed. The lateral approach to the elbow joint was used and the ununited anconeal process was removed. The limb was bandaged after surgery for 7 days to support soft tissue and exercises were restricted. The dog showed normal limb function 3 weeks after surgery. On a telephone conversation with the owner 18 months after surgery, the dog was reported to maintain normal function of the limb.

• Design & Manufacturing
• /
• 제16권3호
• /
• pp.28-33
• /
• 2022

The recent increasing application rate of advanced high-strength steel(AHSS) for automotive parts makes it difficult to ensure the durability of forming tools. Significant load and friction generated during the piercing process of AHSS increase the wear rate and the damage degree to dies. These harsh process conditions also yield product failures, such as dimensional inconsistency of pierced holes and insufficient quality of hole's sheared edge. This study analyzed the effect of punch wear on the sheared surface of pierced parts and the forming load during the piercing process. Wear-shaped punches showed approximately 20% higher piercing load than normal-shaped punches, and the rollover ratio of the sheared surface also increased. It is considered that the dull edge of wear-shaped punches does not penetrate directly into the material but shears after tensioning it in a piercing direction. In addition, wear-shaped punches experienced compressive load even after completing the piercing process during the down-stroke and tensile load during the up-stroke. This load variation is related to the smaller diameter piercing holes produced by wear-shaped punches compared to normal-shaped punches. Thus, we demonstrated the predictability of the wear level of dies through a comparative analysis of the piercing load pattern.

• 한국잠사곤충학회지
• /
• 제13권1호
• /
• pp.61-67
• /
• 1971

본 실험은 이상견이 제사과정에 있어서 사질에 미치는 영향을 구명하기 위해 수행된 바 그 결과를 요약하면 다음과 같다. 1. 견장, 견폭, 견중, 견층중 견층비율은 이상견이 정상견에 비하여 0.83∼4.65%가 떨어진다. 2. 견층의 두께는 20.62∼22.42%가 이상견이 정상견에 비하여 얇다. 3. 견층 sericin의 용해도는 11.75∼30.05％가 이상견이 정상견에 비하여 높다. 4. 견층연감율은 이상견이 정상견보다 6.51∼9.32% 높다. 5. 이상견은 정상견에 비하여 견사장9.43%, 견사량 8.53% 생사량비율 6.72%가 떨어진다 6. 해서율은 이상견이 정상견보다 9.58% 저하하였다. 7. 소절은 이상견이 정상견에 비하여 3점 떨어진다. 8. 대중절은 정상견에 비하여 이상견이 1.5∼3.8배나 많았으므로 대중절성적은 16.3 점이 저하되었는데 이는 특히 split ends가 많은 것에 기인된 것이다. 9. 양견수는 이상견에 있어서 정상견에 비해 1.4∼5.5배가 많고 사조고장의 주요원인이 되는 마디수는 1.9∼3.5 배나 많았다.

• Journal of the Optical Society of Korea
• /
• 제18권2호
• /
• pp.146-150
• /
• 2014

We propose an experimental holographic imaging scheme combining compressive sensing (CS) theory with digital holography in phase-shifting conditions. We use the Mach-Zehnder interferometer for hologram formation, and apply the compressive sensing (CS) approach to the holography acquisition process. Through projecting the hologram pattern into a digital micro-mirror device (DMD), finally we will acquire the compressive sensing measurements using a photodiode. After receiving the data of two holograms via conventional communication channel, we reconstruct the original object using certain signal recovery algorithms of CS theory and hologram reconstruction techniques, which demonstrated the feasibility of the proposed method.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제18권3호
• /
• pp.738-754
• /
• 2024

Side-channel analysis (SCA) is a cryptanalytic technique that exploits physical leakages, such as power consumption or electromagnetic emanations, from cryptographic devices to extract secret keys used in cryptographic algorithms. Recent studies have shown that training SCA models with semi-supervised learning can effectively overcome the problem of few labeled power traces. However, the process of training SCA models using semi-supervised learning generates many pseudo-labels. The performance of the SCA model can be reduced by some of these pseudo-labels. To solve this issue, we propose the HWFilter method to improve semi-supervised SCA. This method uses a Hamming Weight Pseudo-label Filter (HWPF) to filter the pseudo-labels generated by the semi-supervised SCA model, which enhances the model's performance. Furthermore, we introduce a normal distribution method for constructing the HWPF. In the normal distribution method, the Hamming weights (HWs) of power traces can be obtained from the normal distribution of power points. These HWs are filtered and combined into a HWPF. The HWFilter was tested using the ASCADv1 database and the AES_HD dataset. The experimental results demonstrate that the HWFilter method can significantly enhance the performance of semi-supervised SCA models. In the ASCADv1 database, the model with HWFilter requires only 33 power traces to recover the key. In the AES_HD dataset, the model with HWFilter outperforms the current best semi-supervised SCA model by 12%.

• 응용통계연구
• /
• 제29권2호
• /
• pp.301-308
• /
• 2016

공정이 특정 허용범위 내에서 생산을 할 수 있는 지 여부를 결정하는 데 공정능력지수가 사용된다. 공정능력지수 $C_p$, $C_{pk}$ 그리고 $C_{pm}$ 등은 공정의 현황을 추적할 수 있는 활용성이 높은 관리도구로서 특별한 관심을 가진다. 대부분 공정능력지수에 대한 계산결과는 통계적 추정과 가설검정에 초점을 맞춘다. 따라서 $C_p$, $C_{pk}$ 그리고 $C_{pm}$의 추정치 ${\hat{C}}_p$, ${\hat{C}}_{pk}$ 그리고 ${\hat{C}}_{pm}$ 사이의 점근적 성질을 조사하는 것이 의미가 있을 것이다. 이 논문에서는 BN(${\mu}_x,{\mu}_y,{\sigma}^2_x,{\sigma}^2_y,{\rho}$) 하에서 세 가지 추정치 ${\hat{C}}_p$, ${\hat{C}}_{pk}$ 그리고 ${\hat{C}}_{pm}$ 간의 점근적 상관관계를 연구한다. 비정규성을 가진 공정에서는 두 종류의 공정능력지수 간에 상관관계를 정립할 수 있을 것이다.

• 공업화학
• /
• 제16권2호
• /
• pp.217-225
• /
• 2005

H사의 유로변경식 고도하수처리 공법의 제어 변수가 DO와 수온 등으로 한정되어 있어 효율성의 만족도를 충족시켜주지 못하는 현재의 상황을 개선하고자 세 가지 개선방향을 설정하여 Simulation을 통한 Operation Data의 분석 및 장치구성과 실험을 통한 최적제어 Logic을 연구하여 이를 다시 S하수처리장에 설치 적용한 결과이다. 본 실험을 통해서 수온과 유량에 근간한 Operation Mode 변경의 최적화와 이를 통한 동력비 절감을 이루었고 암모니아성 질소의 농도에 따른 Operation Mode의 변경에서 일반 Normal Mode와 병행하여 Save Mode를 새로 적용하여 동력비 절감을 이루었다. 또한 DO 값을 송풍량과 수중폭기기의 교반속도에 의해 비례제어하고 유출수의 암모니아 농도에 따라 DO 값을 제어하여 안정적인 질산화를 이루었다. 이러한 결과는 공정효율의 극대화와 운영 및 유지관리비의 절감을 이루었다.