• Laser Solutions
• /
• v.12 no.1
• /
• pp.14-18
• /
• 2009

Ripple formation of femtosecond laser in stainless steel is investigated using 184 fs pulses with a center wavelength of 785 nm. The effect of the laser polarization relative to the translation direction is observed. For drilling with a certain aspect ratio, reflections at the hole walls take place, leading to a non-uniform intensity distribution deep inside the formed hole. Finally, it is shown that a circular polarization during the drilling process significantly improves the quality of the produced holes.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.451-455
• /
• 1995

The composition and thickness dependence and the ferromagnetic under- and overlayer effect on the magnetoresistance ratio and saturation field of the Co-Ag nano-granular films were investigated. The maximum magnetoresistance (23% at R.T.) in the as-deposited state was obtained in the $3000{\AA}$ $Co_{30} Ag_{70}$ bare alloy film. As the thickness of the alloy films decreased below $500{\AA}$, the MR ratio decreased because of the resistivity increase and the non-uniform film formation. We showed that the ferromagnetic over- and underlayer could reduce the saturation field of the nano-granular films via exchange coupling effect. The magnetoresistance and the saturation field of the $100{\AA}$ alloy film were 3.65 % and 2.85 kOe respectively and those of the under- and overlayered alloy films with $200{\AA}$ Fe were 3.3 % and 1.23 kOe respectively.

• Advances in aircraft and spacecraft science
• /
• v.11 no.1
• /
• pp.1-21
• /
• 2024

The stiffness reduction of cross-ply composite laminates featuring a transverse cracking and delamination within the mid-layer is predicted through utilization of a modified shear-lag model, incorporating a stress perturbation function. Good agreement is obtained by comparing the prediction models and experimental data. The material characteristics of the composite are affected by fluctuations in temperature and transient moisture concentration distribution in desorption case, based on a micro-mechanical model of laminates. The transient and non-uniform moisture concentration distribution induces a stiffness reduction. The obtained results demonstrate the stiffness degradation dependence on factors such as cracks density, thickness ratio and environmental conditions. The present study underscores the significance of comprehending the degradation of material properties in the failure progression of laminates, particularly in instances of extensive delamination growth.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.146-146
• /
• 2011

The blue light emitting diode (LED) structure based on non-polar a-plane (11-20) GaN which was coated TiO2 nanoparticles using spin coating method was grown on r-plane (1-102) sapphire substrates to improve light extraction efficiency. We report on the emission and structural properties with temperature dependence of photoluminescence (PL) and x-ray rocking curves (XRC). From PL results at 13 K of undoped GaN samples, basal plane stacking fault (BSF) and near band edge (NBE) emission peak were observed at 3.434 eV and 3.484 eV, respectively. We also found the temperature-induced band-gap shrinkage, which was fitted well with empirical Varshini's equation. The PL intensity of TiO2 nanoparticles ?coated multiple quantum well (MQW) sample is decayed slower than that of no coating sample with increasing temperature. The anisotrophic strain and azimuth angle dependence in the films were shown from XRC results. The full width at half maximum (FWHM) along the GaN [11-20] and [1-100] directions were 564.9 arcsec and 490.8 arcsec, respectively. A small deviation of FWHM values at in-plane direction is attributed to uniform in-plane strain.

• Steel and Composite Structures
• /
• v.21 no.1
• /
• pp.57-72
• /
• 2016

The Poisson ratio reduction of symmetric hygrothermal aged $[{\theta}_m/90_n]_s$ composite laminates containing a transverse cracking in mid-layer is predicted by using a modified shear-lag model. Good agreement is obtained by comparing the prediction models and experimental data published by Joffe et al. (2001). The material properties of the composite are affected by the variation of temperature and transient moisture concentration distribution in desorption case, and are based on a micro-mechanical model of laminates. The transient and non-uniform moisture concentration distribution give rise to the transient Poisson ratio reduction. The obtained results represent well the dependence of the Poisson ratio degradation on the cracks density, fibre orientation angle of the outer layers and transient environmental conditions. Through the presented study, we hope to contribute to the understanding of the hygrothermal behaviour of cracked composite laminate.

• Journal of Magnetics
• /
• v.12 no.3
• /
• pp.129-132
• /
• 2007

Bismuth-substituted yttrium iron garnet (Bi:YIG, $Bi_{0.5}Y_{2.5}Fe_5O_{12}$) films were deposited with aerosol deposition method and their magnetic and optical properties were investigated as a function of annealing temperature. Since the ceramic films deposited with aerosol deposition method have not a perfect crystal structure due to non-uniform internal stress occurred by mechanical collision during their deposition, the post annealing could be a key process to release its internal stress and to improve its micro structure for optimizing the magnetic and magneto-optic properties of films. The crystallinity of Bi: YIG film was improved with increase of annealing temperature, and the saturation magnetization increased up to 87 emu/cc at $800^{\circ}C$. The Faraday rotation increased up to $1.4deg/{\mu}m$ by annealing at $700^{\circ}C$ around the wavelength of $0.5{\mu}m$. The optical transmittance of the Bi:YIG film was also improved in visible region.

• Korean Journal of Optics and Photonics
• /
• v.20 no.5
• /
• pp.288-293
• /
• 2009

Polarization characteristics of a composite film composed of two optically anisotropic films are analyzed. The procedure to determine the effective optics axis and the equivalent retardation of the composite film is suggested in conjuction with the related ellipsometric expressions. The explicit expressions of the effective optic axis and the equivalent retardation of a non-uniform anisotropic film are derived when all optic axes are parallel. Those expressions of the composite film where optic axes of two constituting anisotropic films are not parallel are also derived. Dependence of those expressions on the polarization state of the incident light or the azimuth angle of the linearly polarized light and their limit when applied to practical use are discussed.

• Structural Engineering and Mechanics
• /
• v.67 no.2
• /
• pp.165-173
• /
• 2018

A simple predicted model using a modified Shear-lag method was used to represent the moisture absorption effect on the stiffness degradation for $[0/90]_{2s}$ composite laminates with transverse cracks and under flexural loading. Good agreement is obtained by comparing the prediction model and experimental data published by Smith and Ogin (2000). The material properties of the composite are affected by the variation of temperature and moisture absorption. The transient and non-uniform moisture concentration distribution give rise to the transient elastic moduli of cracked composite laminates. The hygrothermal effect is taken into account to assess the changes in the normalised axial and flexural modulus due to transverse crack. The obtained results represent well the dependence of the stiffness properties degradation on the cracks density, moisture absorption and operational temperature. The composite laminate with transverse crack loaded in axial tension is more affected by the hygrothermal condition than the one under flexural loading. Through this theoretical study, we hope to contribute to the understanding of the moisture absorption on the composite materials with matrix cracking.

• International journal of steel structures
• /
• v.18 no.5
• /
• pp.1541-1559
• /
• 2018

This paper addresses the dynamic loading characteristics of the shock tube onto sandwich steel beams as an efficient and accurate alternative to time consuming and complicated fluid structure interaction using finite element modeling. The corrugated sandwich steel beam consists of top and bottom flat substrates of steel 1018 and corrugated cores of steel 1008. The corrugated core layers are arranged with non-uniform thicknesses thus making sandwich beam graded. This sandwich beam is analogous to a steel beam with web and flanges. Substrates correspond to flanges and cores to web. The stress-strain relations of steel 1018 at high strain rates are measured using the split-Hopkinson pressure. Both carbon steels are assumed to follow bilinear strain hardening and strain rate-dependence. The present finite element modeling procedure with an improved dynamic impulse loading assumption is validated with a set of shock tube experiments, and it provides excellent correlation based on Russell error estimation with the test results. Four corrugated graded steel core arrangements are taken into account for core design parameters in order to maximize mitigation of blast load effects onto the structure. In addition, numerical study of four corrugated steel core placed in a reverse order is done using the validated finite element model. The dynamic behavior of the reversed steel core arrangement is compared with the normal core arrangement for deflections, contact force between support and specimen and plastic energy absorption.

• Transactions of Materials Processing
• /
• v.33 no.1
• /
• pp.50-54
• /
• 2024

In this paper, the process of extruding Cu-10Fe alloy using a finite element analysis (FEA) was theoretically analyzed. To achieve this, the dependence of strain rate and temperature of the alloy required for the extrusion process was secured by utilizing databases for Cu and Fe and the KHL model. For microstructure analysis, FE-SEM with EDS was used to distinguish the phases present in Cu-10Fe alloy. The mechanical characteristics of Cu-10Fe alloy were secured using the results of fitting the mechanical properties of Copper and Steel from the Deform database to the KHL model. The deformation behavior within the alloy during hot extrusion was analyzed, providing insights into effective stress, effective strain, effective strain rate, and temperature. It was observed that the strain distribution was non-uniform. These research findings contribute to an improved understanding of the hot extrusion process of Cu-10Fe alloy and can aid in predicting the mechanical properties of the material.