• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.1
• /
• pp.10-16
• /
• 2013

This paper discussed a procedure for noise certification of Aircraft and predicting the full scale over-flight noise of propeller from acoustic wind tunnel measurement of small scale propeller. Noise Certification Procedures is established from International Civil Aviation Organization(ICAO). The data manipulations are then discussed in extrapolation to simulation flight distance and flight simulation. One of the most important point of flight simulation is adjustments for differences between wind tunnel test conditions and flight test conditions. To simulated the noise level estimation procedure for noise data post-process, simulate procedures from data of the wind tunnel noise measurement and the flight noise measurement by using a 7kg degree UAV. This study confirmed an effectively noise estimation procedures by wind tunnel noise test and flight noise test.

• Journal of computational fluids engineering
• /
• v.15 no.4
• /
• pp.60-66
• /
• 2010

Unsteady Reynolds Averaged Navier-Stokes(URANS) and Large Eddy Simulation(LES) simulation of an axial flow fan are calculated upon same conditions and computational grids in order to study aeroacoustic noise of an axial flow fan numerically. Results of computed performance and predicted noise are compared with those of measurement. Both performances show accurate results with a significant difference of less than 5%. However, noise of LES result is more close to measured noise qualitatively than URANS. Levels of tonal noises of both LES and URANS are quite similar with those of measured at BPF(Blade Passing Frequency) in sound spectrum. However, as leading edge separation and tip vortex shedding phenomena of LES are showed more clearly than those of URANS, sound level of broadband noise of LES corresponds better than that of URANS, especially.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.672-672
• /
• 2011

This study describes the comparison of noise suppression performances at different locations of two error microphones in active noise control (ANC) for outdoor applications. For this study, 12 different locations were predefined to decide best locations for error sensors in terms of suppressing noise. As shown in Fig. 1, the ANC system with one primary loudspeaker, two secondary loudspeakers and two error microphones is operated by a filtered-x LMS (FXLMS) algorithm which is implemented in a TI 6713 DSP board and Realsys 4713 AD/DA Extension board. The noise for the primary source is a typical road noise measured at a highway roadside. The lengths of adaptive filters of W1 and W2 are varied from 32 to 128 respectively. An intensive computer simulation was accomplished before outdoor ANC experiments. It is expected from the simulation results that the ANC performances are very much dependent upon the locations of the two error microphones.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.210-215
• /
• 2001

CD-ROM Drives Rotating high speed as 10000 rpm cause serious noise and vibration problems. At the high speed, dominant noise is Air Borne Noise produced from high-speed airflow and Structure Borne Noise produced from structural vibration. In this research, vibration and sound characteristics in CD-ROM Drive were studied by the use of experimental analysis and computational simulation. Sound intensity techniques and ODS(Operational Deflection Shape) techniques are applied to identify the acoustic noise source of CD-ROM drive. And Computational simulation using SYSNOISE is conducted for describing the noise behavior.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.393-396
• /
• 2010

In this paper the process of transmitting images signal restore to image corrupted by impulse noise proposed alpha-trimmed mean filter. the proposed filter first identifies the noise pixels using the morphological noise detector and then removes the detected impulse noise using the alpha-trimmed mean filter. these proposed filter can realize the accurate noise detection and it can remove impulse noise effectively while preserving edge region in the image very well. Through the simulation, we compared with the existing methods and capabilties.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1273-1279
• /
• 2001

Precise highway traffic noise simulation and reduction require the accurate data for sound power levels emitted by vehicles, varied to road surface, traffic speed, vehicle types and makers, different from countries to countries. In this study, we have elaboratively measured domestic highway traffic noise and parameters affecting noise levels at the nearside carriageway edge. From numerical simulation using the measured results for highway traffic noise, we propose not only two correction factors to enhance the accuracy of highway traffic sound power estimation using ASJ Model-1998 but also its typical power spectrum according to road surface type. The measured and predicted highway traffic noise levels using the proposed sound power shows little difference within 1 dB.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.800-811
• /
• 2014

Recent developments in the prediction of the contribution of windnoise to the interior SPL have opened a realm of new possibilities in terms of i) how the convective and acoustic sources terms can be identified, ii) how the interaction between the source terms and the side glass can be described and finally iii) how the transfer path from the sources to the interior of the vehicle can be modelled. This work discusses in details these three aspects of wind noise simulation and recommends appropriate methods to deliver required results at the right time based on i) simulation and experimental data availability, ii) design stage at which a decision must be made and iii) time available to deliver these results. Several simulation methods are used to represent the physical phenomena involved such as CFD, FEM, BEM, FE/SEA Coupled and SEA. Furthermore, a 1D and 2D wavenumber transformation is used to extract key parameters such as the convective and the acoustic component of the turbulent flow from CFD and/or experimental data whenever available. This work focuses on the validation of the wind noise source characterization method and the vibro-acoustic models on which the wind noise sources are applied.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.12
• /
• pp.1096-1102
• /
• 2013

The useful practical land shall be reserved when an artificial land covers the railway and road. However, the problem is that since the artificial land places directly on the top of noise sources likely on the railway and road there will arise the weak points, noise and vibration. On this study based on creating the artificial land on the top of a railway vehicle base and placing a tenement on that land, it was comprehended the noise influence from the railway car through the simulation. In order to secure the input value for the simulation, at first measured the noise condition of the railway station building and the railway vehicle base. The output value for the railway station building (place A) was around (53.6~57.6) dB(A), the equivalent continuous sound level for an hour, and for the railway station building (place B) it was around (63.7~68.9) dB. The maximum outdoor noise of the tenement on the artificial land was measured as 64.1 dB(A) under the fixed condition on the simulation modeling. The built purpose of placing the artificial land to prevent the noise influence from the railway met the expectation to be less influenced on the tenement. Rather, because of placing the artificial land the noise level on the lower space could be increased so there requires having a noise control.

• Journal of Environmental Impact Assessment
• /
• v.17 no.4
• /
• pp.213-224
• /
• 2008

Since 1970's rapid urbanization and economic growth, the population was highly increased and residential type was changed from single detached house to high density and high-rise apartment. Recently more high-rise residential building generates more traffic volumes and it makes spatial concentration. The highly traffic volumed road and high residential building was constructed nearby, it occurs noise problem. The purpose of this study is comparing the performance of three type noise barrier between noise source and receiver using a noise map simulation. Three types were composed as road side planting trees, building side planting trees and noise barrier wall. Planting trees is less effective than noise barrier wall as a noise barrier. And they are all effective under 3 stories than over 5 stories, especially noise barrier function can't work over 5 stories.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.8
• /
• pp.606-612
• /
• 2014

Vehicle simulation models for noise and vibration prediction have been developed so far generally in two schemes. One is FE models generally used for problems below 200 Hz such as booming noise, and the other is SEA models for high frequencies of more than 1 kHz, representatively related to sound packages. There have been many researches to develop a simulation model for 200~1000 Hz, so-called mid-frequency region, and this paper shows one practical result that covers the trimmed body of a sedan vehicle. The simulation model is developed based on an FE model, and then FE elements at some areas are substituted with SEA elements to reduce DOFs. SEA panels are described by modal density, radiation efficiency, stiffness and damping characteristics that are found from some numerical assessments. Sound packages are modeled similarly as a conventional SEA model. The results obtained from the hybrid model were compared to experimental results. Predicted pressure and vibrational velocity generally show a good agreement. The developed simulation model and related technology are successfully being used in vehicle development process.