• Journal of KSNVE
• /
• v.8 no.6
• /
• pp.1062-1068
• /
• 1998

This paper describes the vibration characteristics of a high head pump-turbine runner. with nine blades and an outer diameter of 4.410 mm. of the pumped storage power plant. Mode shapes and natural frequencies were obtained by means of both the finite element analysis and modal testing. both in air and in water. The natural frequencies in air were calculated using the finite element method by ANSYS software. In order to confirm calculation results. the natural frequencies and mode shapes of the runner were measured using a hydraulic exciter both in air and in water. Natural frequencies of the pump-turbine runner were found at 174. 310 Hz in air, and at 107. 184 Hz in water. The first mode shape is flat plate mode with two nodal diameter and the second one is also flat plate mode with three nodal diameter. It can be shown that the natural frequencies of the pump-turbine runner in water is reduced approximately 40 ％ due to additional mass effect. Natural frequencies in air predicted by ANSYS software are in good agreement with test results.

• Journal of KSNVE
• /
• v.8 no.4
• /
• pp.623-631
• /
• 1998

The free vibration analyses of the isotropic and composite(CFRP, GFRP) rectangular plates with point supports at the free edge and middle position are performed. The natural frequencies and nodal patterns of plates with point supports are experimentally determined by impact testing using an impact hammer. To compare and verify these experimental results, the finite element analysis is also carried out. The effect of the point support position, the number of point supports, and the anisotropic parameters on the natural frequencies and nodal patterns of cantilevered rectangular plates are investigated.

• Journal of the Korean Institute of Gas
• /
• v.28 no.2
• /
• pp.66-75
• /
• 2024

This paper presents development of a CO₂ injectivity analysis model using nodal analysis for the depleted oil reservoirs in Malaysia. Based on the final well report of an appraisal well, a basic model was established, and sensitivity analysis was performed on injection pressure, tubing size, reservoir pressure, reservoir permeability, and thickness. Utilizing the well testing report of A appraisal well, permeability of 10md was determined through production nodal analysis. Using the basic input data from the A appraisal well, an injection well model was set. Nodal analysis of the basic model, at the bottomhole pressure of 3000.74psia, estimated the CO₂ injection rate to be 13.29MMscfd. As the results of sensitivity analysis, the injection pressure, reservoir thickness, and permeability tend to exhibit a roughly linear increase in injection rate when they were higher, while a decrease in reservoir pressure at injection also resulted in an approximate linear increase in injection rate. Analyzing the injection rate per inch of tubing size, the optimal tubing size of 2.548inch was determined. It is recommended that if the formation parting pressure is known, performing nodal analysis can predict the maximum reservoir pressure and injection pressure by comparing with bottomhole pressure.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.3
• /
• pp.233-245
• /
• 2011

A new BWIM(bridge weigh-in-motion) algorithm using both measured strain and acceleration data is proposed. To consider the effects of bridge vibration on the estimation of moving loads, the dynamic governing equation is applied with the known stiffness and mass properties but damping is ignored. Dynamic displacements are computed indirectly from the measured strains using the beam theory and accelerations are measured directly by accelerometers. To convert a unit moving load to its equivalent nodal force, a transformation matrix is determined. The incompleteness in the measured responses is considered in developing the algorithm. To examine the proposed BWIM algorithm, simulation studies, laboratory experiments and field tests were carried. In the simulation study, effects of measurement noise and estimation error in the vehicle speed on the results were investigated.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.3
• /
• pp.397-403
• /
• 1989

A slight asymmetry exists in Korean beslls due to decorative sculptures, carved figures and casting irregularities. In this study, the influence of the asymmetry on the bell's best frequencies and mode shapes is studied by using finite element method and modal testing. Also measurement techniques of nodal lines and damping ratios of bells with very small beat frequencies are discussed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.2
• /
• pp.131-136
• /
• 2008

Using ultrasonic standing waves, micro particles submerged or flowing in fluid can be manipulated. Due to acoustic radiation force of ultrasound, particles are forced to move to pressure nodal or antinodal lines. In this work, we propose a method to control the position of micro particle in a flow by adjusting the frequency of the standing wave. To this end, standing wave field generation system including a few millimeter thick micro channel was established using an immersible ultrasonic transducer. The present generation system works valid in a frequency range between 2.0 MHz and 2.5 MHz. We observed the SiC particles in water moved to pressure nodal lines by the standing wave. The effect of the channel thickness and operating frequency was also investigated. Interestingly, it was shown that the operating frequency have a close relation with the location of the pressure nodal line. Consequently, it fan be said that the position of particle movement rail be controlled by adjusting the ultrasound frequency. The maximum range of the controllable position was about 261 micrometers under the given condition. The resulted observations reveal the possibility of various applications of the ultrasonic standing wave to the manipulation of particles submerged in a fluid.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.725-730
• /
• 2002

This paper presents an efficient modeling method for open cracked beam structures. An equivalent bending spring model is introduced to represent the structural weakening effect in the presence of open cracks. The proposed method adopts the exact dynamic element method (EDEM) to avoid the difficulty and numerical errors in association with re-meshing the structure. The proposed method is rigorously compared with a commercial finite element code. Experiments are also performed to validate the proposed modeling method. Finally, a diagnostic scheme for open cracked beam structures is proposed and demonstrated through a numerical example.

• Asian Journal of Business Environment
• /
• v.4 no.4
• /
• pp.5-11
• /
• 2014

Purpose - The paper aims to study strategic enterprise resource initiative formation processes. It analyzes the process of managing the strategic resource initiative and discusses its implementation mechanism. A research model for enterprises' strategic development is proposed, which suggests a geometric interpretation for estimating a company's long-term development. Research design, data, and methodology - The analysis employs theoretical studies of modern researchers. The main models used to determine the optimal alternative business strategy are graphic interpretation and mathematical modeling. Results - The hypotheses testing demonstrates the definition of a company's strategic resource initiative and explains the-mechanism or design of its formation. The study presents a geometric prism-refraction model of practice using a strategic resource initiative. Conclusions - An enterprise's strategy could return to its initial state in case of its unexpected deviation as a result of passing through the nodal points. The proposed model allows us to evaluate business performance, its surrounding environment, and the resource management strategy, to determine the necessary scope of strategy changes necessary to bring it back to the original state.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.984-989
• /
• 2008

An estimation of high-order damping in flexible multibody dynamic simulation is introduced in this paper. The suggested damping model based on the experimental modal analysis leads to more accurate correlation results comparing to the traditional linear damping model because it directly uses the modal parameters of each mode achieved from experiment even high frequency modes. The modal parameters until the 5th mode are extracted from the experimental modal testing of the flexible beam using a high speed camera. And using the measured damping ratio and natural frequency until the 5th mode, the generic damping model is constructed. Then, the ANCF (absolute Nodal Coordinate Formulation) simulation results are compared to experimental results until the 5th mode.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.9
• /
• pp.2242-2251
• /
• 1993

The mesh-based frictional contact model has been developed which does not rely on the spatial derivatives of the tool surface. Only points on the surface are evaluated from the description. which can then be simplified because of the relaxed demands placed on it. The surface tangents, normals, and corresponding derivatives at each finite-element node are evaluated directly from the finite-element mesh, in terms of the connecting nodal positions. The advantages accrue because there is no longer a need for a smooth tool surface to assure reasonable normals and derivatives. Furthermore, it can be shown that the equilibrium equations can only be properly written with a special normal derived from the mesh itself. The validity, accuracy, computation time, and stability of mesh-based contact model were discussed with the numerical examples of rounded flat-top and rough, flat-top rounded punch forming operations. Also, the forming process of a automobile inner panel section was simulated for testing the robustness of new contact model. In the discussion, the superiority of new model was examined, comparing with tool-based contact one.