• Journal of the Korean Institute of Gas
• /
• v.20 no.6
• /
• pp.80-88
• /
• 2016

A fire station and scuba have operated filling facilities for respiratory high-pressure cylinder without getting authority or reporting according to High-Pressure Gas Safety Control Act. They need facility improvement and special management to make provision for the time of accident during filling process. The Government have strived to correct illegal operations and suggested an alternative, establishing and operating the safety cabinet. It insures a safety being distance from danger caused by overpressure and a safety provoked by the protective wall equals or superiors. The safety cabinet is required to have an internal structure that smoothly distribute overpressure at the time of rupture. Plus, it needs to minimize fragments. It is also equipped with the performance of protective wall that makes overpressure to outside vent on the place where there is no person (top or bottom). This study calculated the consequence of physical explosion damage and built a prototype of safety cabinet. In addition, through the gas burst test, it derives for the ways to mitigate the physical explosion damage.

• Journal of the Korea Concrete Institute
• /
• v.27 no.3
• /
• pp.253-263
• /
• 2015

Ultra-high strength concrete which have 100 MPa compressive strength or higher can be developed applying RPC(Reactive Powder Concrete). Preventing brittle failure under compression and tension, ultra-high strength concrete usually use the steel fibers as reinforcements. For the effective use of steel fiber reinforced ultra-high strength concrete, estimation of tensile strength is very important. However, there are insufficient research results are available with no relation between them. Therefore, in this study, correlation between compressive strength and tensile strength of ultra-high strength concrete was investigated by test and statistical analysis. According to test results, increasing tendency of tensile strength was also shown in the range of ultra-high strength. Evaluation of test results of this study and collected test results were carried out. Using 284 splitting test specimens and 265 flexural test specimens, equations suggested by previous researchers cannot be applied to ultra-high strength concrete. Therefore, using database and test results, regression analysis was carried out and we suggested new equation for splitting and flexural tensile strength of steel fiber reinforced ultra-high strength concrete.

• Proceedings of the KOSOMBE Conference
• /
• v.1998 no.11
• /
• pp.285-286
• /
• 1998

Virtual Brain-endoscopy is an effective method to detect lesion in brain. Brain is the most part of the human and is not easy part to operate so that reconstructing in 3D may be very helpful to doctors. In this paper, it is suggested that to increase the reliability, method of matching 3D object with the 2D CT slice. 3D Brain-endoscopy is reconstructed with 35 slices of 2D CT images. There is a plate in 3D brain-endoscopy so as to drag upward or downward to match the relevant 2D CT image. Relevant CT image guides the user to recognize the exact part he or she is investigating. VRML Script is used to make the change in images and PlaneSensor node is used to transmit the y coordinate value with the CT image. The result is test on the PC which has the following spec. 400MHz Clock-speed, 512MB ram, and FireGL 3000 3D accelerator is set up. The VRML file size is 3.83MB. There was no delay in controlling the 3D world and no collision in changing the CT images. This brain-endoscopy can be also put to practical use on medical education through internet.

• Journal of Preventive Medicine and Public Health
• /
• v.28 no.1 s.49
• /
• pp.1-12
• /
• 1995

Diatomaceous earth, quarried from the remains of aquatic plants deposited millions of years ago, continues to be a very important raw material with many industrial uses. In its natural state, diatomaceous earth is an amorphous silica with no crystalline pattern. For many uses, however, it is calcinated and calcination converts a portion of the amorphous silica to a crystalline form, cristobalite which is far more fibrogenic. In a factory which produces calcinated diatomaceous earth, seven workers were proved as pneumoconiosis on 1991 and 1992. Authors reviewed medical chart and current status of them. Authors also examined thirty one subjects from the factory with questionnaire, physical examination, spirometry and chest radiography on August 13th 1993. The radiographs were independently interpreted by two radiologists and their findings were classified by International Classification of Radiography of Pneumoconiosis(ILO, 1980). Total and respirable dust of diatomaceous earth were measured on October 1993. The results were as follows; 1. Of 31 workers, 6 (19.4%) were diagnosed as diatomaceous earth pneumoconiosis. There was an increasing tendency in prevalence of pneumoconiosis as the duration of dust exposure gets longer. 2. There were no significant differences in age, smoking rate, alcohol drinking rate, and pulmonary function test results between cases and non-cases. 3. The means of total dust exposures at flour manufacturing, fire brick grinding and packaging, ceramic raws packaging processes exceeded Korean and ACGIH standards, $10mg/m^3$. Above results suggest that engineering controls, periodic environmental and medical surveillance are important for preventing pneumoconiosis in the diatomite factory.

• The Korean Journal of Emergency Medical Services
• /
• v.6 no.1
• /
• pp.141-152
• /
• 2002

The purpose of this study is to provide the basic materials for searching the way of improvement to heighten the emergency medical welfare level by one step further. To achieve this purpose, the subjects of this study were selected 452 college students in Gwangju, using a random sampling method. The statistical analysis methods utilized for analyzing the collected data are frequency analysis, $x^2$ test. The conclusions obtained from these analyses are as following ; 1. In question about necessary optimum number of persons for rescue first aid activity, health and non-health major college students responded by 39.2%, 45.3% respectively that rescue team 15 people, first aid team 3 people is most suitable. But there was no significant difference in major department(p<0.05). 2. In question about security of the public health doctor and the emergency medical technician, all health and non-health major college students are recognizing necessity urgently, but there was no significant difference in major department(p<0.05). 3. In question about 119 rescue first aid team member applying for an examination qualification grant to the department of EMT's graduate, all health and non-health major college students were highest by 52.9%, 52.4% respectively in "necessity" item. But there was no significant difference in major department(p<0.05). 4. Because rescue first aid equipment level appears higher than 41.7% in non-health major college student's case by 54.2% in health major college student's case, health major college students are recognizing that equipment level should be supplemented more but there was no significant difference in major department(p<0.05). 5. In question about equipment supplement, all health and non-health major college students appeared highest by 64.8%, 69.3% in accident type different special equipment. But there was no significant difference in major department(p<0.05). 6. In question about rescue ambulance car size, we could know being thinking that health and non-health major college student each 61.2%, 56.5% is small and narrow that large size of the rescue ambulance amount need. But there was no significant difference in major department(p<0.05). 7. In question about patient's state is worsened, because rescue first aid equipment is inferior, health major college student responded sometimes 55.1%, many 29.5%. very many by 11.5%, while non-health major college student responded 65.8%, 23.1%, 4.0% respectively. There was significant difference in major department(p<0.05). 8. In question about emergency patient must utilize for 119 rescue ambulance car, all health and non-health major college students appeared highest by 38.8%, 41.3% in "not so" item. In question about rescue first aid team's first-aid treatment ability improves more, all health and non-health major college students appeared highest by 58.1% and 58.7% respectively in "improve" item. In question about "119 rescue ambulance car must go more rapidly than now", all health and non-health major college students are recognizing that should be quicker by 58.1%, 60.9% respectively. When called to 119 all health and non-health major college students responded highest by 55.5%, 53.3% respectively that we must receive first-aid treatment direction from a doctor. In question about "119 rescue ambulance car must be made the pay system", all health and non-health major college students responded 74%, 80% respectively in "not so" item. There was significant difference in major department(p<0.05). In conclusions, In oder to provide superior rescue first aid service to people, a public health doctor should be placed in the situation room inside the fire station so that the doctor could instruct the proper emergency treatment suitable for each situation to the rescue first aid team. Also, national education about a first-aid treatment that do to all people is necessarily necessary in emergency delivery system and this should be spread extensively through school education and broadcasting medium and education should be gone side by side, and see that will can save emergency patients' life which is more when these education consists continuously fixed period for public institution of policeman, fire officer etc. specially. And for reinforcement of patient transfer system, public organization must procure special ambulance car so that emergency patient receive first aid treatment while transfer.

• Journal of Korean Society of Forest Science
• /
• v.10 no.1
• /
• pp.29-39
• /
• 1970

Forest fires often destory forests that have taken years to grow in a few minutes. Forest fire therefore, is an important problem in forest management and have caused heavy losses to the nations economy. In order to resolve this problem many investigations have been made in many countries. However, ecological studies on the forest after accidental fire have not yet been made in Korea. In order to conduct such a study, a burned area on Mt. Samak which is located at Dukduwon-ri, Seo-myon, Chunsung-gun, Kangwon-do, was chosen as experimental plot in 1967. The remaining seeds were collected from the burned area, and investigations on their germination rate and their productivity were made comparing to those of the seeds of undemaged area, and following results were obtained. 1. The number of seed collected from the control plots were 740 while it was 537 from the test plots (Table 3, 4). It was considered that this difference between burned and unburned area was mainly due to the fact that some of the seeds had been burnt by the fire, and the unfavorable environmental conditions in the burned area was also considered to be a reason. In the germination rate in the control plots showed 28.1% while it was 3.2% in the test plots. This difference was considered to be due to complete loss of viability of the seed by burning and high heat. 2. In the test plots, sixteen seeds of the Alnus japonica were collected and six of these seeds germinated (index number 100) which was the highest germination rate among the species of collected seeds. From these results, it was considered that a high temperature (above $150^{\circ}C$) caused reduction of the germination rate (Quadrat. 1.2). Seeds of Carex lanceolata var. Nana, were appeared much more in the higher plots than in the lower plots and it seemed to be due to the fact that the forest floor plants were much more abundant in the lower plots than in the higher plots which is covered with shrubbery. And some small seeds midght be able to avoid the effect of fire being burried in the soil or under the gravel. 3. With Pinus densiflora, 43 seeds were collected, and 11 of these germinated in the control plots. However in the test plots, 11 seeds were collected and no seed germinated. This shows that the Pinus densiflora was the weakest in resisting to heat among the observed species in this study. 4. Without exception the germination rate showed a higher index in the herbs than in the woody plants and it is believed that the herbs produced more seed than the wood plants because of the abundance of herbs colony.

• Journal of the Korea Concrete Institute
• /
• v.26 no.5
• /
• pp.651-660
• /
• 2014

Structural members using ultra high strength concrete which usually used with steel fiber is designed with guidelines based on several investigation of SF-RPC(steel fiber reinforced reactive powder concrete). However, there are not clear design method yet. Especially, SF-RPC member should be casted with steam(90 degree delicious) and members with SF-RPC usually used with precast members. Although the most important design parameter is development method between SF-RPC and steel reinforcement(rebar), there are no clear design method in the SF-RPC member design guidelines. There are many controversial problems on safety and economy. Therefore, in order to make design more optimum safe design, in this study, we investigated bond stress between steel rebar and SF-RPC according to test. Test results were compared with previously suggested analysis method. Test was carried out with direct pull out test using variables of compressive strength of concrete, concrete cover and inclusion ratio of steel fiber. According to test results, bond stress between steel rebar and SF-RPC increased with increase of compressive strength of concrete and concrete cover. Increasing rate of bond stress were decrease with increase of compressive strength of SF-RPC and concrete cover significantly. 1% volume fraction inclusion of steel fiber increase the bond stress between steel rebar and SF-RPC with two times but 2% volume fraction cannot affect the bond stress significantly. There are no exact or empirical equations for evaluation of SF-RPC bond stress. In order to make safe bond design of SF-RPC precast members, previously suggested analysis method for bond stress by Tepfers were evaluated. This method have shown good agreement with test results, especially for steel fiber reinforced RPC.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.615-621
• /
• 2018

To enhance the energy saving and comfort of indoors, this study performed a stimulation of sound fluctuation, color temperature, and aroma. The experiment with EEG, HRV, and Vibra images was conducted in an environmental test room with a temperature of $25[^{\circ}C]$, relative humidity of 50[RH%], air current speed of 0.002[m/s], and illuminance of 1000[lux]. The stimulation experiment set up different sensory stimulation conditions, such as before exposure, single-sensory stimulation of fluctuation a=1.106 jazz music, single-sensory stimulation of RED color lighting, single-sensory stimulation of scent aroma, and multi-sensory stimulation of fluctuation a=1.106 jazz music, RED color lighting, and scent aroma. After the multi-sensory stimulation of fluctuation a=1.106 jazz music, RED color lighting and scent aroma, the capacity for work and attention were increased, and the stress index and fatigue degree were decreased. In addition, multi-sensory stimulation of fluctuation a=1.106 jazz music, RED color lighting, and scent aroma were effective in maintaining a stable heart and health. In addition, the Vibra image appeared to decrease tension/anxiety and stress. The multi-sensory stimulation of fluctuation a=1.106 jazz music, RED color lighting, and scent aroma help increase the Neuro-energy more than that by no exposure and single-sensory stimulation.

• The Korean Journal of Emergency Medical Services
• /
• v.14 no.1
• /
• pp.47-63
• /
• 2010

Objective : The objective of this study was to survey the job-related empowerment and job satisfaction of 119 emergency medical technicians provide emergency patients with first aid, to examine the correlation between their empowerment and job satisfaction, and to provide basic materials for developing programs to enhance 119 emergency medical technicians' empowerment and job satisfaction. Methods : The survey was conducted with 249 119 emergency medical technicians working at fire stations in an area of Gyeonggi-do during the period from June 26 to August 21, 2009. Using SPSS 14.0 program, we obtained frequencies percentages, means, and standard deviations, and performed independent two sample t-test, one way ANOVA, and Pearson correlation analysis, and Cronbach's ${\alpha}$. Results : 1) The mean score of the subjects' empowerment was 3.32, and that of their job satisfaction was 2.94. 2) As to difference according to general characteristics, no statistically significant difference was observed in empowerment but job satisfaction was statistically significantly different according to gender(t = 2.296, p = .023). 3) As to difference according to job related characteristics, empowerment was significantly different according to license type(F = 3.767, p = .011), and job satisfaction was statistically significantly different according to position(t = 3.222, p = .042), fire fighting experience(t = 2.689, p = .035), and first aid experience(t = 3.991, p = .007). 4) Empowerment was in a positive correlation with job satisfaction(r = .502, p = .000) in general, and by the sub areas of job satisfaction, the correlation with empowerment was high in order of job itself(r = .695, p = .000), interaction area(r = .493, p = .000), organizational demand area(r = .328, p = .000), working condition area(r = .153, p = .015), and wage area(r = .137, p = .031). By the sub areas of empowerment, the correlation with job satisfaction was high in order of significance(r = .424, p = .000), influence(r = .397, p = .000), competence(r = .372, p = .000), and self determination(r = .259, p = .000). Conclusion : The 119 emergency medical technicians' empowerment was in a high correlation with their job satisfaction, and had a strong effect on it. This suggests that 119 emergency medical technicians' job performance can be enhanced by improving their empowerment. These results are expected to be useful in making human resource management plans to enhance 119 emergency medical technicians' job satisfaction by empowering them.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.642-649
• /
• 2021

Energy saving standard for buildings are strengthened, the application of exterior insulation finishing system and thickness of insulation materials are increasing. Most buildings with exterior insulation finishing system is applied organic insulating material. Organic insulating material have workability, economic feasibility, reduction in construction cost, and excellent thermal insulation performance. However, Organic insulating material is very vulnerable to heat, so when a fire occurs, rapid fire spread and toxic gas are generated, causing many casualties. Inorganic insulating material can be non-combustible performance, but it is heavy and has low thermal insulation performance. Mineral wool has higher thermal insulation performance than other types of inorganic insulating material, but mineral wool is disadvantageous to workability and vulnerable to moisture. Glass bubble are highly resistant to water and chemically stable substances. In addition, the density of the glass bubble is very low and the particles are spherical, fluidity is improved by the ball bearing effect. Glass bubbles can be used with cement-based ino rganic insulating material to impro ve the weight and thermal insulatio n perfo rmance o f cement-based inorganic insulation. This study produced a inorganic insulating materials were manufactured using cement-based materials and glass bubble. In order to evaluate the insulation performance and flame retardant performance of cement-based super light-weight inorganic insulating materials using with glass bubble, insulation performance or flame retardant and non-combustible performance were evaluated after manufacturing insulating materials using micro cement and two types of glass bubbles. From the test result, Increasing the mixing ratio of glass bubbles improved the insulation performance of cement-based super light-weight inorganic insulating materials, and when the mixing ratio of glass bubbles was 10%, it sho wed sufficient flame retardant and no n-co mbustible perfo rmance.