• Transactions on Electrical and Electronic Materials
• /
• v.7 no.5
• /
• pp.257-261
• /
• 2006

Nano-structured carbon nitride $(CN_x)$ films were prepared by reactive RF magnetron sputtering with a DC bias at various deposition conditions, and the physical and electrical properties were investigated. FTIR spectrum indicated an ${alpha}C_3N_4$ peak in the films. The carbon nitride film deposited on Si substrate had a nano-structured surface morphology. The grain size was about 20 nm and the deposition rate was $1.7{\mu}m/hr$. When the $N_2/Ar$ ratio was 3/7, the level of nitrogen incorporation was 34.3 at%. The film had a low dielectric constant. The metal-insulator-semiconductor (MIS) capacitors that the carbon nitride was deposited as insulators, exhibited a typical C-V characteristics.

• Korean Journal of Materials Research
• /
• v.14 no.2
• /
• pp.141-145
• /
• 2004

Silicon nitride thin films were deposited by atomic layer deposition (ALD) technique in a batch-type reactor by alternating exposures of precursors. XJAKO200414714156408$_4$ or$ SiH_2$$Cl_2$ was used as the Si precursor, $NH_3$ was used as the N precursor, and the deposited films were characterized comparatively. The thickness of the film linearly increased with the number of deposition cycles, so that the thickness of the film can be precisely controlled by adjusting the number of cycles. As compared with the deposition using$ SiCl_4$, the deposition using $SiH_2$$Cl_2$ exhibited larger deposition rate at lower precursor exposures, and the deposited films using $SiH_2$$Cl_2$ had lower wet etch rate in a diluted HF solution. Silicon nitride films with the Si:N ratio of approximately 1:1 were obtained using either Si precursors at $500^{\circ}C$, however, the films deposited using $SiH_2$$Cl_2$ exhibited higher concentration of H as compared with those of the $SiC_4$ case. Silicon nitride thin films deposited by ALD showed similar physical properties, such as composition or integrity, with the silicon nitride films deposited by low-pressure chemical vapor deposition, lowering deposition temperature by more than $200^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.240-243
• /
• 2002

Carbon nitride films have been deposited on Si(100) substrate by a high voltage discharge plasma combined with laser ablation in a nitrogen atmosphere. The films were grown both with and without the Presence of an assisting focused Nd:YAG laser ablation. The laser ablation of the graphite target leads to vapor Plume plasma expending into the ambient nitrogen arc discharge area. X-ray photoelectron spectroscopy and Auger electron spectroscopy were used to identify the binding structure and the content of the nitrogen species in the deposited films. The surface morphology of the films was studied using a scanning electron microscopy Data of infrared spectroscopy and x-ray photoelectron spectroscopy indicate the existence of carbon-nitrogen bonds in the films. The x-ray diffraction measurements have also been taken to characterize the crystal properties of the obtain films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.94-97
• /
• 1997

We investigated the sheet resistance properties of tungsten nitride thin films deposited by RF and DC sputtering system. It deposited at various conditions that determine the sheet resistance. The properties of the sheet resistance of these films were measured under various conditions. Sheet resistance analysed under the flow rate of the argon gas and contents of nitrogen from nitrogen-argon gas mixtures. We found that these sheet resistance were largely depend on the temperature of substrate, gas flow rate and RF power. Very high and low sheet resistance of tungsten films obtained by DC sputtering. As the increase of contents of nitrogen gas obtained from nitrogen-argon gas mixture, tungsten nitride thin films deposited by the reactive DC sputtering and the sheet resistance of these films were increased.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.1013-1019
• /
• 2007

Amorphous silicon and silicon-nitride films were deposited using plasma-enhanced chemical vapor deposition (PECVD) method at $150^{\circ}C$. As fraction of $H_2$ in source gas was increased, characteristics of low-temperature silicon-nitride films approached those of conventional high-temperature films; the refractive index approached 1.9 and the ratio of nitrogen-hydrogen bonds to silicon-hydrogen bonds increased. And also, as fraction of $H_2$ in source gas was increased, characteristics of low-temperature silicon films approached those of conventional high-temperature films; refractive index and optical band gap approached 4.2 and 1.8 eV, and $[Si-H]/([Si-H]+[Si-H_2])$ increased. Lower RF power and process-pressure made the amorphous silicon films to be better properties. Increase of $H_2$ ratio seemed as the common factor to get reliable amorphous silicon and silicon-nitride films for thin-film-transistors (TFTs) at low temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.872-875
• /
• 2003

Carbon nitride($CN_x$) thin films were deposited on quartz substrates using reactive RF magnetron sputtering system at uarious deposition conditions and investigated dielectric characteristics. Samples for capacitance measurements were of the MIM(Metal-Insulator-Metal) type devices. Aluminum film electrodes were prepared by a vacuum thermal evaporation method before and after the deposition of carbon nitride films. Capacitances were measured by a FLUKE PM6306 RCL Meter at room temperature. Current-voltage(I-V) characteristics and resistivity were measured by a CATS CA-EDA semiconductor test and analyzer. The carbon nitride films showed ${\alpha}-C_3N_4$ and ${\beta}-C_3N_4$ etc. peaks through Raman and FTIR. Observed surface of film and side structure using SEM(Scanning Electron Microscope), and measured thickness of film by ${\alpha}-step$. We can find that the dielectric constant was the lowest value in 50% nitrogen ratio and the resistivity was the highest value in 70% nitrogen ratio.

• Journal of Korean Vacuum Science & Technology
• /
• v.1 no.1
• /
• pp.30-37
• /
• 1997

Interactions of Cu films with Si substrates separated by thin layers of molybdenum and molybdenum nitride were investigated in the viewpoint of diffusion barrier to copper. the diffusion barrier behavior of the layers was studied as functions of deposition and annealing conditions by cross-sectional transmission electron microscopy and Nomarski microscopy. the layers deposited at $N_2$ gas ratios of 0.4 and 0.5 exhibited good diffusion barrier behaviors up to $700^{\circ}C$, mainly due to the phase transformation of molybdenum to $\gamma$-Mo$_2$N phase. The increase in the N gas ratio in deposition elevates the lower limit of barrier failure temperature. Futhermore, amorphous molybdenum nitride films deposited at 20$0^{\circ}C$ and 30$0^{\circ}C$ did not fail, while the crystalline $\gamma$-Mo$_2$N films deposited at 40$0^{\circ}C$ and 50$0^{\circ}C$ showed signs of interlayer interactions between Cu and Si after annealing at 75$0^{\circ}C$ for 30 minutes. Therefore, the amorphous nature of the molybdenum nitride layer enhanced its ability to reduce Cu diffusion and its stability as a diffusion barrier at elevated temperatures.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.05a
• /
• pp.152-155
• /
• 2006

Carbon nitride ($CN_X$) films were prepared by reactive RF magnetron sputtering system at various deposition conditions and the C-V characteristics of MIS(metal - insulator - semiconductor) capacitors that have the structures of Al/$CN_x$/p-Si/Al and Al/$CN_x$/$Si_3N_4$/p-Si/Al were investigated. The resistivity of carbon nitride was above $2.40{\times}10^8{\Omega}{\cdot}cm$ at room temperature. The C-V plot showed a typical capacitance-voltage characteristics of semiconductor insulating layers, while it showed hysterisis due to interface charges. Amorphous carbon nitride (a-$CN_x$) films, that have relatively high resistivity and low dielectric constant could be useful as interlayer insulator materials of VLSI(very large-scale integration) and ULSI(ultra large-scale integration).

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.115-118
• /
• 1990

Recently, it has been reported that the Insulating films deposited by PECVD show some degradation under somewhat high electric field. In this paper, we Introduce silicon nitride films deposited by LCVD, and evaluate the breakdown and wear-out of these films by TDDB test. Further, failure times against electric field are examined and acceleration factors $\gamma$ are obtained for each case. As a result, it is shown that the breakdown and wear-out limitation for these films is improved.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.165-169
• /
• 2001

Carbon nitride films were grown on Si (100) substrate by a laser-electric discharge method with and without a magnetic field assistance. The magnetic field leads to vapor plume plasma expending upon the ambient arc discharge plasma area. Influence of the magnetic field has resulted in increase of a crystallite size in the films due to bombardment (heating) of Si substrates by energetic carbon and nitrogen species generated during cyclotron motion of electrons in the discharge zone. Many crystalline grains were observed in the morphology of the deposited films by scanning electron microscopy. In order to determine the structural crystalline parameters, X-ray diffraction (XRD) was used to analysis the grown films.