• 분석과학
• /
• 제22권2호
• /
• pp.141-147
• /
• 2009

Laser induced breakdown spectroscopy (LIBS)의 정량분석에 대한 측정의 정확도를 향상시키고자, 플라즈마의 특성을 분석하여, 상대적으로 안정적인 Outer sphere에 해당하는 영역을 측정하는 방법으로 Cu alloy sample을 측정하여 분석하였다. 신호의 높은 재현성을 고려한 측정 조건에서 측정이 수행되었으며, 600 mtorr 진공상태에서 20 mm정도의 크기로 플라즈마를 성장시켜, Outer sphere 영역인 플라즈마 성장방향으로 6.0 mm 지점을 측정하였다. 그 결과 Cu의 선형 분석 $R^2$ 값은 0.9886로, Ni의 $R^2$ 값은 0.9988로 획득하였으며, 측정오차는 Ni의 경우 기존보다는 향상된 0.78%의 측정오차를 획득하였다.

• 한국표면공학회지
• /
• 제46권6호
• /
• pp.248-257
• /
• 2013

It is generally recognized that thin Pd-Cu alloy films fabricated by sputtering show a wide range of microstructures and properties, both of which are highly dependent on the sputtering conditions. In view of this, the present study aims to investigate the relationship between the performance of hydrogen separation membranes and the microstructure of Pd alloy films depending on sputtering deposition conditions such as substrate temperature, working pressure, and DC power. We fabricated thin and dense Pd-Cu alloy membranes by the micro-polishing of porous Ni support, an advanced Pd-Cu sputtered multi-deposition under the conditions of high substrate temperature / low working pressure / high DC power, and a followed by Cu-reflow heat-treatment. The result of a hydrogen permeation test indicated that the selectivity for $H_2/N_2$ was infinite because of the void-free and dense surface of the Pd alloy membranes, and the hydrogen permeability was 10.5 $ml{\cdot}cm^{-2}{\cdot}min^{-1}{\cdot}atm^{-1}$ for a 6 ${\mu}m$ membrane thickness.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.936-936
• /
• 2006

Bulk amorphous materials have been intensively studied to apply for various advanced industry fields due to their high mechanical, chemical and electrical properties. These materials have been produced by several techniques such as mechanical alloying, melt spinning and gas atomization, etc. Among them, the atomization is the most potential technique for commercialization due to high cooling rate during solidification of the melt and mass productivity. However, the amorphous powders still have some limitations because of their low ductility and toughness. Therefore, intensive efforts have to be carried out to increase the ductility and toughness. In this study, the Ni-based amorphous powder was produced by the gas atomization process. And in order to increase the ductile toughness, ductile Cu phase was coated on the Ni amorphous powder by spray drying process. The characteristics of the as-synthesis powders have been examined and briefly mentioned. The master alloy with $Ni_{57}Zr_{20}Ti_{16}Si_2Sn_3$ was prepared by vacuum induction melting furnace with graphite crucible and mold. The atomization was conducted at $1450^{\circ}C$ under the vacuum of $10^{-2}$ torr. The gas pressure during atomization was varied from 35 to 50 bars. After making the Ni amorphous powders, the spray drying was processed to produce the Cu -coated Ni amorphous composite powder. The amorphous powder and Cu nitrate solution were mixed together with a small amount of binder and then it was sprayed at temperature of $130^{\circ}C$ and rotating speed of 15,000 R.P.M.

• 전자공학회논문지A
• /
• 제28A권12호
• /
• pp.31-38
• /
• 1991

The current-voltage characteristics at annealed Be-Cu alloy(1.8-2 wt% Be, 0.2 wt% Co+Ni) interfaces have been studied by means of the cyclic voltammetric method. The specimens were annealed in nitrogen gas($N_{2}$) furnace at 36$0^{\circ}C$ for 1.5 hours. After annealing, the vickers hardness(HV) was increased from 210 to 385. The used solutions were distilled water(H$_{2}$O), 10$^{-3}M\;CsNO_{2},10^{-2}M\;KCl,10^{-2}M\;KOH,10^{-4}M\;H_{2}SO_{4}$ aqueous electrolytes, and ethylalcohol ($C_{2}H_{5}OH$), etc. The cyclic voltammograms showed significant current-voltage characteristics between the annealed and unannealed specimens at the same conditions. The age hardening and the related surface potential barrer and dissolution effects have been observed during the whole experimental process. The dissolution process of annealed Be-Cu alloys was effectively retarded by the age hardening phenomenon. The age hardening effect also raised the surface potential barrier of Be-Cu alloys. The interfacial phenomena of Be-Cu alloys seem to be one of good models for understanding the activation process.

• 한국수소및신에너지학회논문집
• /
• 제13권2호
• /
• pp.151-158
• /
• 2002

The hydorgen storage alloys were produced by melting in arc melting furnace and then solution heat treated at $1,100^{\circ}C$ followed by pulverization. The chemical analysis on the samples showed that the major elements of misch metal(Mm) were La, Ce, Pr and Nd with impurity less than 1wt.%. X-ray diffraction indicated that the structure for these samples were a single phase of hexagonal with $CaCu_5$ type. Compared to the initial particle size $100{\sim}110{\mu}m$, the many fine cracks were found and particle size decreased to $14{\mu}m$ for $MmNi_{4.5}Mn_{0.5}$ after hydriding/dehydring test run. To activate the sample the vessel filled with hydrogen storage alloys was first evacuated for for at $70^{\circ}C$ and then treated for 10.5hr under hydrogen pressure of 20atm for $MmNi_{4.5}Mn_{0.5}$ alloy. The experimental data showed that the hydrogen storage alloy of $MmNi_{4.5}Mn_{0.5}$ had superior adsorption and description properties within a temperature rang of $40^{\circ}C{\sim}80^{\circ}C$ and also they had a good P-C-T curve.

• International Journal of Advanced Culture Technology
• /
• 제3권2호
• /
• pp.132-137
• /
• 2015

The purpose of this paper was to investigate the effects of solution treatment time and Sr-modification on the microstructure and property of the Al-Si piston alloy. It was found that as-cast microstructures of unmodified and Sr-modified Al-Si alloys consisted of a coarse acicular plate of eutectic Si, $Cu_3NiAl_6$ and $Mg_2Si$ phases in the ${\alpha}$-Al matrix but different in size and morphology. Both size and inter-particle spacing of Si particles were significantly changed by increasing of the solution treatment time. After a short solution treatment, the coarse acicular plate of the eutectic Si appears to be fragmented. Fully modified microstructure of Sr-modified alloy can reduce the solution treatment time to shorter compared to unmodified alloy. The maximum of a peak hardness value is found in the very short solution treatment of both Al-Si piston alloys. Compared to 10 h solution treatment, the solution treatment of 2-4 h is sufficient to achieve appropriate microstructures and hardness. The short solution treatment is very useful to increase the productivity and to reduce the manufacturing cost of the Al-Si piston alloys.

• 마이크로전자및패키징학회지
• /
• 제24권1호
• /
• pp.83-90
• /
• 2017

본 연구에서는 미세피치 패키지 적용을 위한 기초 실험으로 thin ENEPIG(Electroless Nickel Electroless Palladium Immersion Gold) 도금층을 형성하여 솔더링 특성을 평가하였다. 먼저, Sn-3.0Ag-0.5Cu (SAC305) 솔더합금에 대한 thin ENEPIG 도금층의 젖음 특성이 평가되었으며, 순차적인 솔더와의 반응에 대한 계면반응 및 솔더볼 접합 후 고속 전단 시험을 통한 접합부 기계적 신뢰성이 평가되었다. 젖음성 시험에서 침지 시간이 증가함에 따라 최대 젖음력은 증가하였으며, 5초의 침지 시간 이후에는 최대 젖음력이 일정하게 유지되었다. 초기 계면 반응 동안에는 $(Cu,Ni)_6Sn_5$ 금속간화합물과 P-rich Ni 층이 SAC305/ENEPIG 계면에서 관찰되었다. 연장된 계면반응 후에는 P-rich Ni 층이 파괴 되었으며, 파괴된 P-rich Ni 층 아래에는 $(Cu,Ni)_3Sn$ 금속간화합물이 생성되었다. 고속 전단 시험의 경우, 전단속도가 증가함에 따라 취성 파괴율이 증가하였다.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2010년도 임시총회 및 하계학술연구발표회
• /
• pp.82-84
• /
• 2010

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 춘계학술발표강연 및 논문개요집
• /
• pp.143-143
• /
• 2003

현대 산업이 발전함에 따라 다양한 기기들의 초소형화가 급속히 진행되고 있다. 이러한 요구에 부응하기 위하여 미세구동소자(Microelectromechanical system)의 개발이 많은 연구 그룹들에 의해서 이루어지고 있다. 미세구동소자에 응용을 하기 위해 개발되어지고 있는 여러 가지 소재들 중 $\ulcorner$형상기억합금 $\lrcorner$은 기존의 바이메탈이나 피에조 소자에 비하여 작동거리가 우수하기 때문에 그 가능성을 인정받고 있지만, 벌크재료는 느린 냉각속도 때문에 반응속도가 느린 단점이 있기 때문에 박막화 할 필요성이 있다. 이러한 이유로 여러 그룹들에 의해 형상기억합금의 박막화가 시도되고 있으나, 조성에 의해 특성의 변화가 심한 형상기억합금의 정밀한 조성제어가 힘들다고 알려져 있다. 몇몇 연구 그룹에서 RF magnetron sputtering법을 이용하여 Ti-Ni합금 박막을 성공적으로 제조하였다는 보고가 있지만, 타겟 조성 및 형태 등의 정밀한 제어가 필요하므로 3원 합금 박막 등을 제조할 경우에는 또 다시 타겟의 조건을 정밀하게 제어해야 할 필요성이 있다. 따라서 본 연구에서는 산화물 박막등의 제조에 있어서 타겟 조성과 제조된 박막 조성이 잘 일치하여 조성제어가 쉽게 이루어진다고 알려져 있는 PLD법을 도입하여 형상기억합금 박막제조에 적용가능한지를 검토하는 것을 목적으로 하였다.

• 열처리공학회지
• /
• 제17권6호
• /
• pp.346-355
• /
• 2004

The flame quenching process has been employed to modify the surfaces of commercial marine propeller material, aluminum bronze alloy (Cu-8.8Al-5Ni-5Fe), and the microstructure, hardness and wear properties of the flame-quenched layers have been studied. The thermal history was accurately monitored during the process with respect to both the designed maximum surface temperature and holding time. The XRD and EDX analyses have shown that at temperatures above $T_{\beta}$, the microstructure consisting of ${\alpha}+{\kappa}$ phases changed into the ${\alpha}+{\beta}^{\prime}$ martensite due to an eutectoid reaction of ${\alpha}+{\kappa}{\rightarrow}{\beta}$ and a martensitic transformation of ${\beta}{\rightarrow}{\beta}^{\prime}$. The ${\beta}^{\prime}$ martensite phase formed showed a face-centered cubic (FCC) crystal structure with the typical twinned structure. The hardness of the flame-quenched layer having the ${\alpha}+{\beta}^{\prime}$ structure was similar to that of the ${\alpha}+{\kappa}$ structure and depended sensitively on the size and distribution of hard ${\kappa}$ and ${\beta}^{\prime}$ phases with depth from the surface. As a result of the sliding wear test, the wear resistance of the flame-quenched layer was markedly enhanced with the formation of the ${\beta}^{\prime}$ martensite.