• 대한치과교정학회지
• /
• 제45권4호
• /
• pp.198-208
• /
• 2015

Objective: To quantify, for each activation, the effect of preactivations of differing distribution and intensity on the neutral position of T-loops (7-mm height), specifically the horizontal force, moment to force (M/F) ratio, and load to deflection ratio. Methods: A total 100 loops measuring $0.017{\times}0.025$ inches in cross-section were divided into two groups (n = 50 each) according to composition, either stainless steel or beta-titanium. The two groups were further divided into five subgroups, 10 loops each, corresponding to the five preactivations tested: preactivations with occlusal distribution ($0^{\circ}$, $20^{\circ}$, and $40^{\circ}$), gingival distribution ($20^{\circ}$), and occlusal-gingival distribution ($40^{\circ}$). The loops were subjected to a total activation of 6-mm with 0.5-mm iterations. Statistical analysis was performed using comprised ANOVA and Bonferoni multiple comparison tests, with a significance level of 5%. Results: The location and intensity of preactivation influenced the force intensity. For the M/F ratio, the highest value achieved without preactivation was lower than the height of the loop. Without preactivation, the M/F ratio increased with activation, while the opposite effect was observed with preactivation. The increase in the M/F ratio was greater when the preactivation distribution was partially or fully gingival. Conclusions: Depending on the preactivation distribution, displacement of uprights is higher or lower than the activation, which is a factor to consider in clinical practice.

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1322-1329
• /
• 1994

The effect of thermal stratification on the stratified flow past a circular cylinder was examined in a wind tunnel. Turbulent intensities, the rms values of temperature and turbulent convective heat flux as well as the velocity and temperature profiles in the cylinder wake with a strong thermal gradient of $200^{\circ}C/m$ were measured by using a hot-wire and cold-wire combination probe. It is found that the temperature field affects as an active contaminant, so that the vertical growth of vortical structure is suppressed and the strouhal number decreases with increasing the extent of stratification. And also, the wake structure can not sustain their symmetricity about the wake centerline and vertical turbulent motion dissipates faster than that of the neutral case when such a strong thermal gradient is superimposed. It is evident that the turbulent mixing in the upper half section is stronger than that of the lower of the wake in a stably stratified flow because the turbulent intensities and convective heat flux in the upper half section are larger than those of the lower half of the wake.

• Steel and Composite Structures
• /
• 제22권4호
• /
• pp.837-853
• /
• 2016

This paper presents the experimental and numerical study on the distribution of transverse and longitudinal residual stresses in cold-formed thick-walled structural steel rectangular hollow sections manufactured by indirect technique. Hole-drilling method is employed to measure the magnitude of the transverse and longitudinal surface residual stress distribution, and the effects of the residual stresses are evaluated qualitatively by sectioning method. It is shown that compared to normal cold-formed thin-walled structural hollow sections (SHS), the cold-formed thick-walled SHS has similar level of residual stress in the flat area but higher residual stresses in the corner and welding areas. Both the transverse and longitudinal residual stresses tend to open the section. In order to predict the surface residual stresses in the corners of the cold-formed thick-walled SHS, an analytical model is developed. 2D finite element simulation of the cold bending process is conducted to validate the analytical approach. It is shown that in analyzing bending for thick-walled sections, shifting of neutral axis must be considered, since it would lead to nonlinear and non-symmetrical distribution of stresses through the thickness. This phenomenon leads to the fact that cold-formed thick-walled SHSs has different distribution and magnitude of the residual stresses from the cold-formed thin-walled SHSs.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 춘계학술대회 논문집
• /
• pp.183-188
• /
• 2002

In locations where the cost or concrete is relatively high, or in situations where the weight or concrete members is to be kept to a minimum, it may be economical to use hollow reinforced concrete vertical members. Hollow reinforced concrete columns with low axial load, moderate longitudinal steel percentage, and a reasonably thick wall were found to perform in a ductile manner at the flexural strength, similar to solid columns. However, hollow reinforced concrete columns with high axial load, high longitudinal steel percentage, and a thin wall were found to behave in a brittle manner at the flexural strength, since the neutral axis is forced to occur away from the inside face of the tube towards the section centroid and, as a result, crushing of concrete occurs near the unconfined inside face of the section. If, however, a steel tube is placed near the inside face of a circular hollow column, the column can be expected not to fail in a brittle manner by disintegration of the concrete in the compression zone. Design recommendation and example by moment-curvature analysis program for curvature ductility are presented. Theoretical moment-curvature analysis for reinforced concrete columns, indicating the available flexural strength and ductility, can be conducted providing the stress-strain relation for the concrete and steel are known. In this paper, a unified stress-stain model for confined concrete by Mander is developed for members with circular sections.

• Journal of the Korean Physical Society
• /
• 제73권12호
• /
• pp.1855-1862
• /
• 2018

A reliable set of low-energy electron collision cross sections for the triethoxysilane (TRIES) molecule was derived based on the measured electron transport coefficients for a pure TRIES molecule by using an electron swarm method and a two-term approximation of the Boltzmann equation. The electron transport coefficients calculated using the derived set are in good agreement with experimental value over a wide range of E/N values (ratio of the electric field E to the neutral number density N). The present electron collision cross section set for the TRIES molecule, therefore, is the most reliable so far for plasma discharges and for materials processing using the TRIES molecule. Moreover, the electron transport coefficients for the TRIES-Ar and the $TRIES-O_2$ mixtures were also calculated and analyzed over a wide range of E/N for the first time.

• 복합신소재구조학회 논문집
• /
• 제6권2호
• /
• pp.8-16
• /
• 2015

Prestressed concrete (PSC) is a method in which prestressed tendon is placed inside and/or outside the reinforced concrete member and the compressive force applied to the concrete in advance to enhance the engineering properties of concrete member which is weak under tension. In this paper we suggested the precast PSC girder assembled with segments of portable size and weight at the factory. The segments of precast PSC girder will be delivered and assembled as a unit of PSC girder at the site. Consequently, we suggested new-type of precast segmented PSC girder with different shapes of segment cross-section (i.e., I-shape, Box-shape). To mitigate the problems associated with the field splice between the segments of precast PSC girder anchor system is attached near the neutral axis of the girder and relatively uniform compression throughout the girder cross-section is applied. Prior to the experimental investigation, analytical investigation on the structural behavior of precast PSC girder was performed and the serviceability (deflection) and safety (strength) of the girder were confirmed. In addition, 4-point bending test on the girder was conducted to investigate the structural performance under bending. From the experimental investigation, it was found that the precast PSC girder spliced with 3 and 5 segments has sufficient in serviceability and safety conditions and it was also observed that the point where the segments spliced has no defects and the girder behaves as a unit.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.57-60
• /
• 2008

기존의 철근콘크리트 구조물 시스템에서 철근은 사용연한이 지날수록 염분 및 습기, 염화물 등 외부환경에 의해 부식된다. 이러한 철근의 부식은 최종적으로 콘크리트 구조물의 성능 저하와 수명 단축을 유발시키는 주요 원인이 되기 때문에 최근 Fiber Reinforced Polymers(FRP)를 이용하여 철근을 대체할 수 있는 보강근을 개발하고자 하는 연구가 활발히 진행 중이다. FRP 보강근 콘크리트 보의 전단강도에 대한 기존 연구에 따르면 FRP 보강근은 철근에 비해 탄성계수가 낮기 때문에 동일 하중 수준에서 철근 콘크리트보다 균열폭이 커지고 균열이 크게 진행하게 되어 전단강도도 감소하는 것으로 알려져 있다. 본 연구에서는 FRP 보강근 콘크리트 보의 전단강도를 실험적으로 측정하고 기존에 제시 된 선행 규준의 예측식을 실험값과의 비교를 통해 검증해보고자 하였다. 본 연구에서 수행한 실험결과에서는 전단경간비가 증가할수록 전단강도는 감소하는 것으로 나타났다.

• 한국실내디자인학회논문집
• /
• 제24권2호
• /
• pp.125-133
• /
• 2015

Gaze induction characteristics in space vary depending on characteristics of spatial components and display. This study analyzed dominant eye-fixation characteristics of three zones of department store space. Eye-fixation characteristics depending on spatial components and positional relationship can be defined as follows. First, [**.jpg] was used as an extension in the process of storing the image photographed during image data processing for analysis in pixels and due to compressed storage of image data, the image produced with a clear boundary was stored in neutral colors. To remove this problem, the image used in operation was re-processed in black and white and stored in the [**.bmp] format with large capability, at the same time. As the result, the effort caused by unnecessary colors in the program operation process was corrected. Second, the gaze ratio to space area can be indicated as a strength of each gaze zone and when analyzing the gaze strength of the three zones, the left store was a zone with a "little strong" gaze strength of "102.8", the middle space was a zone with an "extremely weak" gaze strength of "89.6" and the right store was a zone with an "extremely strong" gaze strength of "117.2". Third, the IV section had a strong strength of gaze on the middle space and the right store and the V section showed a markedly strong strength of gaze on the left and right stores. This tendency was the same as the VI section with the strongest gaze strength and the right store had a little strong gaze strength than the left store.

• 한국건축시공학회지
• /
• 제21권4호
• /
• pp.293-303
• /
• 2021

국내 PC공장은 PC 유공 슬래브를 생산하기 위해 자동화 설비를 도입하거나 매입물 삽입을 통해 중공 단면을 구현하지만 PC공장의 과다한 초기투자비용이 생산원가의 증가라는 주요 원인으로 작용하기에 다른 대안이 필요한 상황이다. 따라서 본 연구에서는 PC 유공 슬래브 부재 생산시 고무 튜브를 내부 속빈 공간을 형성하는 거푸집으로 사용함으로써 다양한 중공 형상의 성형 및 대단면화, 초경량화, 신속생산 대응 가능을 통한 생산성 확보에 기여하고자 한다.

• 전기전자학회논문지
• /
• 제26권3호
• /
• pp.355-363
• /
• 2022

우리나라는 2050년 탄소중립을 목표로 신재생에너지 중심으로 에너지 공급원을 전환하고 확대하는 계획을 추진 중이다. 신재생에너지의 간헐적 특성으로 에너지 공급이 불안정성이 커짐에 따라 정확한 신재생에너지 발전량 예측의 중요성이 함께 커지고 있다. 이에 따라 정부는 신재생에너지를 집합화하여 관리하기 위한 소규모 전력중개시장을 개설하였고, 재생에너지 발전량 예측제도를 도입하여 예측정확도에 따라 정산금을 지급하는 제도를 시행 중이다. 본 논문에서는 우리나라 신재생에너지 전원의 대부분을 차지하는 태양광 발전에 대하여 통계적 및 인공지능 모형을 이용하여 예측모델을 구현하였으며, 각 모형의 예측정확도 결과를 비교 분석하였다. 비교 모델 중에서 CNN-LSTM(Convolutional Long Short-Term Memory Neural Networks) 모형이 가장 높은 성능을 가짐을 확인하였다. 예측정확도에 따른 예측제도 정산금 수익을 추정해보았고, 예측보유 기술 수준에 따라 수익 편차가 24% 정도 커질 수 있음을 확인하였다.