• 한국환경과학회지
• /
• 제25권10호
• /
• pp.1407-1415
• /
• 2016

In this study, we investigated the relationship between noise reduction and the community structure of nine groups of typical plant communities as well as the reduction in noise at different frequencies. The semantic differential method was adopted to explore the perception of noise reduction. The results indicated that there was a significantly positive correlation between noise reduction and coverage, a significantly negative correlation between noise reduction and bifurcate height, and a negative correlation between noise reduction and bare rate. However, there was no significant correlation between noise reduction and height, diameter at breast height, or crown width. The reduction of middle-frequency noise was better than that of low- and high-frequency noise. The indicators "quiet" and "calm" showed that plant communities could reduce the noise perceived by humans. However, overly dense woodland caused nervousness, fear, depression, and other negative effects. Relatively open environments and those with large forest gaps obtained the highest evaluation.

• 한국소음진동공학회논문집
• /
• 제24권1호
• /
• pp.28-34
• /
• 2014

This study provides the numerical finite-element method(FEM) estimating the friction noise induced by the negative slope in the friction-velocity curve. The friction noise due to the friction-velocity curve is experimentally investigated through the pin-on-disk setup. The measured squeal frequency is estimated by FEM. The friction curve is measured by the friction test, then it is applied to the complex eigenvalue analysis. The results shows that the experimental squeal frequency can be determined by the FEM analysis. Also, it is emphasized that the negative friction-velocity slope is essential in generating friction noise in the pin-on-disc system.

• International journal of advanced smart convergence
• /
• 제9권2호
• /
• pp.20-27
• /
• 2020

Sound event detection in real-world environments suffers from the interference of non-stationary and time-varying noise. This paper presents an adaptive noise reduction method for sound event detection based on non-negative matrix factorization (NMF). In this paper, we proposed a deep learning model that integrates Convolution Neural Network (CNN) with Non-Negative Matrix Factorization (NMF). To improve the separation quality of the NMF, it includes noise update technique that learns and adapts the characteristics of the current noise in real time. The noise update technique analyzes the sparsity and activity of the noise bias at the present time and decides the update training based on the noise candidate group obtained every frame in the previous noise reduction stage. Noise bias ranks selected as candidates for update training are updated in real time with discrimination NMF training. This NMF was applied to CNN and Hidden Markov Model(HMM) to achieve improvement for performance of sound event detection. Since CNN has a more obvious performance improvement effect, it can be widely used in sound source based CNN algorithm.

• 한국정보전자통신기술학회논문지
• /
• 제16권4호
• /
• pp.167-172
• /
• 2023

본 논문에서는 3개의 부궤환 루프를 가진 저잡음 위상고정루프를 제안하였다. 기존 구조의 위상고정루프는 하나의 부궤환 루프로 구성되어 있어 잡음 특성 개선이 쉽지 않다. 추가된 부궤환 루프는 지터 특성을 결정하는 전압제어발진기의 입력 전압 크기를 줄여주는 역할을 하여 기존 구조로 쉽지 않은 잡음 특성 개선을 가능하게 해준다. 시뮬레이션 결과는 부궤환 루프가 추가될 때마다 지터 특성이 개선되는 것을 보여주고 있다. 전력의 경우 10% 정도 약간 상승하게 되지만, 지터 특성은 2배 정도 개선된다. 제안된 위상고정루프는 1.8V 180nm CMOS 공정을 이용하여 Hspice로 시뮬레이션 하였다.

• 대한기계학회논문집A
• /
• 제39권7호
• /
• pp.681-686
• /
• 2015

본 연구는 steel 재질의 판과 Cu, Ni, Al, Mg 재질의 핀 간에 발생하는 마찰에 의한 마찰소음 특성을 왕복운동 및 회전운동 실험장치를 통하여 연구하였다. 실험 결과 미끄럼 속도에 대한 마찰곡선의 음의 기울기가 소음발생시점에 영향을 주었다. 특히 Cu 가 소음발생시점과 음의 기울기 측면에서 마찰소음방지에 가장 우수한 재질임을 확인하였다.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2003년도 종합학술발표회 논문집 Vol.13 No.1
• /
• pp.638-648
• /
• 2003

An active capacitance circuit is analyzed in depth and its application to active RF BPF with low noise figure is discussed. The characteristics of the active capacitance circuit made of FET[1] exhibits negative resistance and conventional capacitance, which is easily controlled. However, it is difficult to make the negative resistance adequate in the designated frequency range due to the lack of detailed analysis, which could make an active circuit unstable as the frequency is going higher or lower. In this paper, we analyzed the negative resistance characteristics of active capacitance circuits and also presented the method that the flatness of passband can be controlled. Finally we have designed a 4-stage active BPE, which results in bandwidth of 100 MHz, 0,04 dB insertion loss, 0.2 dB ripple, and noise figure of 2.4 dB at 1.75 GHz band.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.624-629
• /
• 2003

In this paper, broadband shunt technique for increasing transmission loss is experimentally investigated. Piezoelectric shunt damping is studied using resonant shunt circuit and negative capacitor shunt circuit. A resonant shunt circuit is implemented by using a resistor and inductor. Negative Capacitor shunt damping is similar in nature to resonant shunt damping techniques, as a single piezoelectric material is used to dampen multi-mode. Performance of both methods is experimentally studied for noise reduction. This is based upon SAE J1400 test method and a transmission loss measurement system is provided for it. This paper will present the test setup fer transmission loss measurement and the tuning procedure of shunt circuits. Finally the results of sound transmission tests will be shown.

• 한국소음진동공학회논문집
• /
• 제23권5호
• /
• pp.423-430
• /
• 2013

The characteristics of friction noise due to the friction-velocity curve is experimentally investigated through the pin-on-disk setup. The rotation speed of the disk is controlled in order to produce the sliding speed variation. Then, the friction coefficient and the corresponding friction noise are simultaneously measured with respect to the sliding speed between the steel disk and aluminum pin. The experimental results show that the negative friction-velocity slope is essential in generating friction noise.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계 학술대회논문집(수송기계편)
• /
• pp.29-32
• /
• 2005

This paper presents experimental analysis of a friction-driven wheel that is responsible for wheel squeal. Squeal noise generating mechanism and environment of train u heels has been tried to reproduce under laboratory condition. Scale down size rail and wheel are made and influential parameters to squeal noise are measured, e. g. frictional force, pressure between rail and wheel, creep speed of rail. Negative damping characteristic curve are calculated currently. Necessary relating computational analysis is also carried on.

• 한국전자파학회논문지
• /
• 제15권6호
• /
• pp.590-598
• /
• 2004

저잡음 특성과 함께 부성 저항과 수동 캐패시턴스의 특성을 보이도록 설계된, 직렬 피드백 회로를 이용한 FET능동 캐패시턴스 회로를 심도 있게 분석하였고, 이를 저잡음 능동 대역통과 여파기에 적용하였다. 부성저항을 이용한 마이크로파 대역 능동 여파기의 설계방식은 비교적 여러 차례 소개되었으나, 원하는 주파수에서 적절한 부성저항 성분을 구현하는 데에는 아직 어려움이 있으며, 이로 인한 능동 회로의 안정성 저하와 대역내 평탄도 증가 등으로 인해 실제 상용화에는 다다르지 못하고 있다. 이들 문제를 해결하고 실제 상용화에 이르기 위해서는 부성저항 회로의 세밀한 분석이 필요하며, 이를 이용한 부성저항 성분의 제어를 가능하도록 해야 한다. 이에 본 논문에서는 능동 캐패시턴스 회로의 부성저항 성분을 분석하였고, 또한 BPF의 통과대역의 평탄도를 개선할 수 있는 방법을 제시하였다. 제작된 4단 대역통과 여파기는 중심주파수 1.99 ㎓에서 60 MHz의 대역폭을 가지며, 0.67 ㏈ 삽입손실, 0.3 ㏈ 이내의 대역내 평탄도와 3.0 ㏈의 잡음 지수 특성을 보였다.