• Journal of Technologic Dentistry
• /
• v.27 no.1
• /
• pp.97-104
• /
• 2005

The effect of Nb on interfacial bonding characteristics of Ni-Cr alloy for porcelain fused to metal crown (PFM) has been studied in order to investigate oxide layer. A specimens, which is 0.8mm in thickness, were fired at 1,000$^{\circ}C$ with four tests such as air, vacuum, air for 5 minutes and vacuum for 5 minutes in order to examine an oxide behavior of alloy surface generated by the adding of Nb to be controlled at a rate of 0, 1, 3 and 5. It observed oxide film form of the fired specimens with optical microscope and scanning electron microscope (SEM), and chemical formation of them with energy disperse X-ray spectroscopy (EDX). The other specimens, which is 2mm in thickness, were fired at 1,000$^{\circ}C$ with air and vacuum in order to analyze the diffusion behaviors of alloy-porcelain interface by X-ray dot mapping. The results of this study were as follows: 1. The observation of microstructure of specimens by SEM showed that the more Nb content is high, the more much intermediate compound of rich Nb is observed. 2. The surface morphology of oxide film is most dense in 3% Nb. The heat treatment in air constitutes denser oxide film than heat treatment under vacuum. 3. The diffusion behavior of oxide layer by X-ray dot mapping showed that Si, Al of porcelain diffuse toward metal.

• Journal of the Korean Magnetics Society
• /
• v.17 no.5
• /
• pp.198-204
• /
• 2007

The effects of annealing temperature on electromagnetic wave absorption characteristics in $Fe_{73.5}Cu_1Nb_3Si_{15.5}B_7$ (at%) alloy flakes/polymer composite sheets available for quasi-microwave band have been investigated. The composite sheet including the magnetic flakes annealed at $425{\sim}475^{\circ}C$ for 1 h exhibited highest power loss in the GHz frequency range as compared with the sheets composed of the alloy flakes annealed at higher temperature than $475^{\circ}C$ or in as-milled state. Moreover the imaginary part of complex permeability had largest value in the GHz frequency range for the sheets including the flakes annealed at $425{\sim}475^{\circ}C$. The large value of power loss of the sheets including the magnetic flakes annealed at $425{\sim}475^{\circ}C$ was attributed to the high imaginary part of the complex permeability. However, because of its large transmission parameter $S_{21}$, the composite sheet having the magnetic flakes annealed at $525^{\circ}C$ showed low power loss.

• Journal of the Korean Ceramic Society
• /
• v.43 no.1 s.284
• /
• pp.55-61
• /
• 2006

The microwave dielectric properties and low temperature sintering of $Ca[Ti_{1-x}(Ni_{1/3}Nb_{2/3})_x]O_3$ system were investigated at the sintering temperature $1,200\~1,350^{\circ}C$. The density and quality factors $(Q{\times}f)$ increased while dielectric constants slightly decreased with the decrease of Ti. The dielectric constant, quality factor, and temperature coefficient of resonance frequency $(\tau_f)$ were 64, 17,000 GHz, and $-9.1\;ppm/^{\circ}C$ respectively, when $CaTi_{1/2}(Ni_{1/3}Nb_{2/3})_{1/2}O_3$ ceramics were sintered at $1,300^{\circ}C$ for 4 h. $2Li_2O-B_2O_3$ was added to $CaTi_{1/2}(Ni_{1/3}Nb_{2/3})_{1/2}O_3$ to decrease the sintering temperature for LTCC application. The microwave dielectric properties of the samples sintered at $925^{\circ}C$ for 2 h with the addition of $6\;wt\%\;2Li_2O-B_2O_3$ were $\varepsilon_r=48.7,\;Q{\times}f=8,460\;GHz$, and $\tau_f=+5.6ppm/^{\circ}C$. Compatibility test of the composition with silver electrode shows no reaction with silver electrode, implying the feasibility as a high-K LTCC material.

• Fire Science and Engineering
• /
• v.16 no.4
• /
• pp.15-19
• /
• 2002

This dissertation is about the development of $BaTiO_3$-type PTC(Positive Temperature Coefficient) thermistor by composition method. A multilayer-type PTC samples were fabricated under optimal conditions after setting the experimental composition equation as ($Ba_{0.95-x}$S $r_{0.05}$$Ca_{x}$ )$TiO_3$-$0.01TiO_2$-$0.01SiO_2$-$\alpha$$MnCO_3$-$\beta$N $b_2$ $O_{5}$.) and their testing results were analyzed. The optimal sin-tering and cooling temperatures were 13$50^{\circ}C$ for two hours and $100^{\circ}C$/h for an hour, respectively; By composing Ca and Mn, dopants to lower the resistivity at room temperature, and Nb, a dopant to raise peak resistivity(Ca:5 mol%, Mn:0.08 mol%, Nb:0.18 mol%), appropriately, a PTC thermistor, having the characteristics of relatively low resistivity at room temperature and high peak resistivity and a good temperature coefficient, has been developed. And we find that it is possible of application for fire detection sensor.r.r.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1968-1970
• /
• 1999

본 연구에서는 RF 마그네트론 스퍼터링법으로 CoNbZrPd 비정질 연자성 박막을 제조하여 Pd의 첨가 효과와 자장중 열처리에 의한 특성 변화에 대해 연구하였다. Pd가 4.34 at% 첨가된 $Co_{87.56}Nb_{6.45}Zr_{1.65}Pd_{4.34}$ 박막은 비정질 구조이며 Pd 첨가에 의해 보자력은 0.54 Oe으로 감소하였으며, 이방성 자계는 10.45 Oe로 Pd를 첨가하지 않은 CoNbZr 비정질 박막 보다 특성이 향상되었다. $Co_{87.56}Nb_{6.45}Zr_{1.65}Pd_{4.34}$ 비정질 박막은 $400^{\circ}C$까지 비정질 상을 유지하고 있지만, 연자기 특성이 열화되어 보자력이 증가하고 이방성자계가 급격히 감소하였지만, 포화 자화는 크게 변화지 않았다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1989.06a
• /
• pp.70-73
• /
• 1989

(1-x-y)Pb($Zn_{1/3}Nb_{2/3})O_3-Ba(Zn_{1/3}Nb_{2/3})O_3-PbTiO_3(0.12{\leq}x{\leq}0.21, 0.24{\leq}y{\leq}0.33$) ternary compound ceramics were fabricated by the mixed oxide method. The sintering temperature and time were 1050 [$^{\circ}C$], 2[hr]. Morphotropic phase boundary region was chosen for the composition. 0.55 PZN-0.21 BZN-0.24 PT specimen had the highest value of relative dielectric constants, 5353. The curie temperature of specimens were increased linearly with PT content. Near the morphotropic phase boundary, electro-mechanical coupoling factor and mechanical quality factor of the specimens had the highest values.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.11b
• /
• pp.539-544
• /
• 1996

핵연료 피복관용 신합금으로 개발되고 있는 여러 가지 Zr합금에서 생성되는 석출물의 특성을 규명하기 위하여 EDX가 부착된 TEM을 이용하여 석출물에 관한 연구를 수행하였다. Zrl.4Sn0.2Fe0.1Cr 합금에서는 두 종류의 석출물이 생성되는데 하나는 석출물의 대부분을 차지하는 HCP 구조의 Zr(Cr,Fe)$_2$ 석출물로서 이는 둥근 형태를 유지하며 결정립내나 결정립계에 관계없이 널리 분산되어 분포된다. 다른 하나의 석출물은 극히 일부에서만 관찰되는 Zr$_2$(Fe,Si)성분의 석출물로서 이는 tetragonal 구조를 갖는다. Zr0.5Nb0.6Fe0.3V 합금에서는 tetragonal (Zr,Nb)$_2$(Fe,V)석출물이 형성되며, Nb이 1.0 wt.% 첨가된 Zr1.0Nb0.6Fe0.3V 합금에서는 HCP 구조의 (Zr,Nb)(Fe,V)$_2$ 석출물과 BCC 구조인 $\beta$-Zr이 생성된다. Zr1.0Nb0.6Fe0.3V 합금을 제외하고는 대부분의 합금에서 석출물은 약 1.0 $\mu$m의 크기를 나타냈다. 합금 조성이 다를 경우에 석출물 크기와 35$0^{\circ}C$ 부식 특성과는 연관성이 없는 것으로 나타났다.

• 한국초전도학회:학술대회논문집
• /
• v.13
• /
• pp.26-26
• /
• 2003

• 한국초전도학회:학술대회논문집
• /
• 2008.08a
• /
• pp.51-51
• /
• 2008

• Journal of the Korean Ceramic Society
• /
• v.40 no.3
• /
• pp.279-285
• /
• 2003

Ferroelectric S $r_{0.9}$B $i_{2.1}$T $a_{1.8}$N $b_{0.2}$ thin films with 200 nm thicknesses were deposited on Pt/Ti $O_2$/ $SiO_2$/Si Substrates by a sol-gel method. In these experiments, Sr(O $C_2$ $H_{5}$)$_2$, Bi(TMHD)$_3$, Ta(O $C_2$ $H_{5}$)$_{5}$ and Nb(O $C_2$ $H_{5}$)$_{5}$ were used as precursors, which were dissolved in 2-methoxyethanol. After UV-irradiation and RTA processes, the remanent polarization value (2 $P_{r}$) of SBTN thin films with annealed at $650^{\circ}C$ was 8.49 and 11.94 $\mu$C/$\textrm{cm}^2$ at 3 V and 5 V, respectively.