• Journal of Korean Society of Forest Science
• /
• v.85 no.1
• /
• pp.84-95
• /
• 1996

Environmental pollution has recently been progressed in the metropolitan and industrial areas of Korea and concerns have been evolved against the chronic effects of the pollution on natural ecosystem. This study was carried out to investigate the environmental pollution impacts on ion input into forest ecosystems and soil environmental changes. Study plots were established at Seoul, Ulsan, Yeochon, and Seosan for pollution sites and at Pyungchang for a non-pollution site. Atmospheric deposition was measured with rain, throughfall, and stem flow samples collected in the forest areas. Soil chemical properties were investigated to compare the pollution impacts on the sites. Precipitation acidity in the metropolitan and industrial areas ranged from pH 4.5 to 5.5, showing the levels lower than pH 5.8 of mountain area. Ion concentrations in the precipitation had increased significantly while passing the crown layer in the metropolitan and industrial areas, showing the increase by 4 times at the maximum. Total ion input in the metropolitan and industrial areas was greater than that in mountain area by approximately 2-3 times. Soil acidification caused by acidic ion input seemed to be greatest at Seoul, showing pH 1 decrease compared to that of Pyungchang. Soil canon contents were relatively high in the metropolitan and industrial areas. Although the canon leaching loss was not apparent, soil acidification process seemed to be continued by acidic ion input. Environmental pollution in the metropolitan and industrial areas exerted changes in ion input into the forest ecosystems and soil conditions. The chronic effects of environmental pollution should be monitored and investigated further to explain the processes of ecosystem change and the impacts on plant growth.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.38 no.3
• /
• pp.98-106
• /
• 2010

This study focuses on the appropriate planting soil for Vitex rotundifolia by planting soil. Different soil depth levels were achieved at 15cm and 25cm in the green roof module system that was created with woody materials for a $500{\times}500{\times}300mm$ area. The soil mixture ratio was $S_{10}$, $L_{10}$, $S_7L_3$, $S_5L_5$, $P_7P_1L_2$, $P_6P_2L_2$, $P_5P_3L_2$ and $P_4P_4L_2$. This study was carried out over five months between April and September, 2006. The amount of soil moisture tends to decrease according to the planting soil. For the experimental items $S_{10}$, $S_7L_3$ and $S_5L_5$, the amount of soil moisture tends to decrease rapidly. However, for the experimental items $P_7P_1L_2$, $P_6P_2L_2$, $P_5P_3L_2$ and $P_4P_4L_2$, conditions containing perlite and peat moss, the amount of moisture tends to decrease more gradually. As a result, the use of soil-improving amending for the afforestation planting of roofs with a low level of management is need. After experimenting with the ratio of soil mixture for Vitex rotundifolia, the planting soil for experimental item $P_6P_2L_2$, $P_5P_3L_2$ and $P_4P_4L_2$ appeared excellent. For experimental item $S_{10}$, the growth of Vitex rotundifolia seemed to be weaker than that of others, because of the low levels of moisture and organic matter in the soil. For experimental item $L_{10}$, there appeared to be a low level of growth, even when the levels of moisture and organic matter were high. This may have occurred because of the low level of soil pH and the excessive amount of exchangeable cation. At the depth of 25cm, the growth of Vitex rotundifolia is vigorous overall. For experimental item at 15cm, Vitex rotundifolia was able to survive for 14 days without any rainfall and Vitex rotundifolia was better in amended soil, $P_6P_2L_2$, $P_5P_3L_2$ and $P_4P_4L_2$, than natural soil, SL.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.38 no.3
• /
• pp.33-40
• /
• 2010

Many trails have been built and utilized in each sub-basin of Apsan Park. This study focused on the conditions and the present flora of several overused trails within three basins called Kun-Gol, Anjiroung-Gol, and Meaja-Gol in Apsan Park. There are two purposes for this study. The first is to make a plan for restoration by classifying the type of damage to these overused trails. The second is to provide preliminary data for reestablishing a more pleasant urban nature park. As a result of the survey, the average length of these trails is 9.0km and mean width is 2.0 to 2.6m. 2,108m of the sections studied(23.4% of the total) had exposed root, 3,199m of the sections studied (35.5% of the total) had exposed rock, 3,270m of the sections studied(36.6% of the total) displayed damaged pathways, and 4,841m of the sections studied (53.8% of the total) had higher soil hardness. Eighty-three areas of deterioration were found and there has been extensive property destruction. As an indication of human disturbances, the Naturalization Index and Urbanization Index appeared as: Kun-Gol, 7.0%, 5.5%; Anjiroung-Gol, 8.3%, 4.5%; Meaja-Gol 8.6%, 6.2%; in total, 7.8%, 8.3%. As a method of checking the level and extent of the damage process, an impact rating classification was used at each point on the trails. Kun-Gol had the highest rating and Anjiroung-Gol had the lowest rating in impact rating classification. With the impact rating classification, it was found that each trail would continue to worsen, meaning that roots and rocks are more likely to be further exposed and the trail width will continue to widen through overuse. An actual plan for reparations and restoration of the trails is needed through further study.

• Korean Journal of Environment and Ecology
• /
• v.28 no.6
• /
• pp.751-761
• /
• 2014

This study was carried out to analyze the vegetation properties, soil characteristics and ordination of Rhododendron brachycarpum population in South Korea. Rhododendron brachycarpum were mainly distributed along the Ulleungdo and Baekdudaegan of the Korean penninsula and it's population was located at an elevation of 872m to 1466m. The Rhododendron brachycarpum population was classified into Taxus cuspidata var. latifolia dominant population, Magnolia sieboldii dominant population, Thuja koraiensis dominant population and Rhododendron brachycarpum typical population. The composition of soil properties in the same areas are as follows: organic matter, total nitrogen, available phosphorous, exchangeable $K^+$, exchangeable $Ca^{2+}$, exchangeable $Mg^{2+}$ contained, and soil pH. The capacities of these chemical properties of the soil ranged from 10.45~15.28%, 0.37~0.61%, $0.21{\sim}0.35cmol^+/kg$, $0.39{\sim}2.54cmol^+/kg$, $0.17{\sim}0.50cmol^+/kg$, $18.28{\sim}22.81cmol^+/kg$ and 4.66~5.23 respectively. The results of the correlation between communities and soil conditions of vegetation of Rhododendron brachycarpum by DCCA ordination method are as follows: Taxus cuspidata var. latifolia dominant population was found in the very steep sloped area that has low percentage of total organic matter and nitrogen than other populations. Magnolia sieboldii dominant population and Thuja koraiensis dominant population was found in the steep sloped area that has high percentage of total organic matter and nitrogen than other populations. Thuja koraiensis dominant population was found in the gentle sloped area that has high percentage of altitudinal and rock exposure. Current status of Rhododendron brachycarpum is very vulnerable with a collection of herbs constantly threatening the species' survival. Thus, concrete conservation plans to protect natural habitats should be set up as soon as possible.

• Korean Journal of Environment and Ecology
• /
• v.31 no.2
• /
• pp.230-251
• /
• 2017

According to the survey on higher fungi from 2009 to 2011 and also in 2015 in Byeonsanbando National Park, a total of 2 division, 6 class, 18 orders, 61 families, 157 genera and 323 species were observed. In case of Agaricales, there were 23 families, 67 genera and 153 species; Boletales, there were 6 families, 27 genera and 45 species; Russulales, there were 3 family, 4 genera and 40 species; Polyporales, there were 6 family, 21 genera, 28 species. Thus, most of them belonged to the following 4 orders: Agaricales, Russulales, Boletales and Polyporales. Dominant species belonged to Boletaceae (37 species), Russulaceae (36 species), Agaricaceae (28 species) and Amamtaceae (25 species). For the habitat environment, the ectomycorrhizal mushrooms were 40.2% (poisonous mushrooms, 46 species; edible & medicinal mushrooms, 51 species; unknown edible & poisonous mushrooms, 26 species), litter decomposing and wood rotting fungi 35.3%(poisonous mushrooms, 10 species; edible & medicinal mushrooms, 52 species; unknown edible & poisonous mushrooms, 46species), grounding Fungi 22.3%(poisonous mushrooms, 8 species; edible & medicinal mushrooms, 31 species; unknown edible & poisonous mushrooms, 29 species). Monthly, most of poisonous mushrooms, edible & medicinal mushrooms and unknown edible & poisonous mushrooms were found in July and August. In terms of altitude, the most species were observed at 1~99m and the populations dropped by a significant level at an altitude of 200m or higher. It seemed that the most diversified poisonous mushrooms, edible & medicinal mushrooms and unknown edible & poisonous mushrooms occurred at climate conditions with a mean air temperature at $24.0{\sim}25.9^{\circ}C$, the highest air temperature at $28.0{\sim}29.9^{\circ}C$, the lowest air temperature at $20.0{\sim}21.9^{\circ}C$, a relative humidity at 77.0~79.9% and a rainfall of 300.0~499.9mm.

• Korean journal of applied entomology
• /
• v.27 no.2
• /
• pp.117-124
• /
• 1988

An Investigation of insect pests in rice stored was carried out in Jeonnam region of Korea. The total of 2 class, 7 orders 16 families and 25 species were recorded in Lepidoptera; 8, Coleoptera; 11, Orthoptera; 1, Thysanura 1, blattaria; 2, Hymenoptera; 1 and mites; 2 spe-cies. The important species among them were Sitotroga cerealella, Ephestia cautella, Paral-ipsa gularis, Poldia, in Lepidoptera, and Sitophilus orzae, Oryzaephilus surianmensis, Cryptolestes ferrugineus, Tribolium castaneum, Tenebroides mauritanicus, Attagenus japonicus, in Coleoptera and Blatella germanica, in Blattaria and Acarus siro Petrobia latens, in mites. The duration of maximum occurrence were the late June to mid July for Sitotroga cerealella, the mod July to early August for Oryzaephilus surianmensis the mid July to August for Tribolium castaneum, the early July to late July for Sitophilus orzae, the mid June to early July for Attagenus japonicus the mid June to late Spetember for Blatella germanica and the late April to late May for Acarus siro and Petrobia latens, respectively in investigation, Blatella germanica(Blattaria) which was no problem in stored rice insect till now was mainly distributed a coastal plain and period of occurrence was long amount of occurrence was great. Rice weevil has 4 generations under natural conditions and the peak of 1st perood time was ranged from middle of jun. to last decade of Jun., 2nd period was from the lats decade of Jul. to first decade of Aug., 3rd period was from middle of Sep. to late Sep., 4th period was middle of Oct. to early Nov.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.12
• /
• pp.1098-1125
• /
• 2000

A review on the papers published in the Korean Journal of Air-Conditioning and Refrigerating Engineering in 1998 and 1999 has been done. Focus has been put on current status of research in the aspect of heating, cooling, ventilation, sanitation and building environment. The conclusions are as follows. 1) A review of the recent studies on fluid flow, turbomachinery and pipe-network shows that many experimental investigations are conducted in applications of impingement jets. Researches on turbulent flows, pipe flows, pipe-networks are focused on analyses of practical systems and prediction of system performance. The results of noise reduction in the turbomachinery are also reported. 2) A review of the recent studies on heat transfer analysis and heat exchanger shows that there were many papers on the channel flow with the application to the design of heat exchanger in the heat transfer analysis. Various experimental and numerical papers on heat exchanger were also published, however, there were few papers available for the analysis of whole system including heat exchanger. 3) A review of the recent studies on heat pump system have focused on the multi-type system and the heat pump cycle to utilize treated sewage as the heat source. The defrosting and the frosting behaviors in the fin-tube heat exchanger is experimentally examined by several authors. Several papers on the ice storage cooling system are presented to show the dynamic simulation program and optimal operation conditions. The study on the micro heat pipes for the cooling of high power electronic components is carried out to examine the characteristics of heat and mass transfer processed. In addition to these, new type of separate thermosyphon is studied experimentally. 4) The recent studies on refrigeration/air conditioning system have focused on the system performance and efficiency for new alternative refrigerants. New systems operating with natural refrigerants are drawing lots of attention. In addition to these, evaporation and condensation heat transfer characteristics of traditional and new refrigerants are investigated for plain tubes and also for microfin tubes. Capillary tubes and orifice are main topics of research as expansion devices and studies on thermophysical properties of new refrigerants and refrigerant/oil mixtures are widely carried out. 5) A review of the recent studies on absorption cooling system shows that numerous experimental and analytical studies on the improvement of absorber performance have been presented. Dynamic analysis of compressor have been performed to understand its vibration characteristics. However research works on tow-phase flow and heat transfer, which could be encountered in the refrigeration system and various phase-change heat exchanger, were seemed to be insufficient. 6) A review of recent studies on duct system shows that the methods for circuit analysis, and flow balancing have been presented. Researches on ventilation are focused on the measurement of ventilation efficiency, and variation of ventilation efficiency with ventilation methods by numerous experimental and numerical studies. Furthermore, many studies have been conducted in real building in order to estimate indoor thermal environments. Many research works to get some information for cooling tower design have been performed but are insufficient. 7) A review on the recent studies on architectural thermal environment and building mechanical systems design shows that thermal comfort analysis is sitting environment, thermal performance analysis of Korean traditional building structures., and evaluation of building environmental load have been performed. However research works to improve the performance of mechanical system design and construction technology were seemed to be insufficient.

• Korean Journal of Environment and Ecology
• /
• v.26 no.4
• /
• pp.498-511
• /
• 2012

Mountainous wetland have many species such as II grade endangered species of wild flora and fauna(Drosera rotundifolia) and environmental indicator species(Utricularia racemosa, Habenaria linearifolia, Parnassia palustris, Molinia japonica, etc.). Accordingly, the mountainous wetlands is very important. However, most mountainous wetlands will disappear by natural or artificial aridness processes. Thus, it needs to manage mountainous wetland for protecting from aridness. This study has found out the wetland status of the environmental ecology and aridness processes moreover, it has suggested ways of improving wetland conservation plan and wetland aridness management plan. According to the results of topography structure survey, Hwaeom wetland's altitude is ranged within 750~810m(87.4%), and slope is less than $10^{\circ}$. There was ideally suited mountainous wetland. However, the water supply(1.6 meters depth and 0.8 meters wide) was built on under the wetland. For that reason, there was concerned about the aridness processes by sweeping away peat layer and dropping the water level. The distribution area of hygrophyte was narrowed to 6.7% whereas, woody plants and xerophytic plants was achieved a dominant position. If it leaves the situation as it is, the mountainous wetland will be developed next succession as forest ecosystem. Therefore, in order to sustain the mountainous wetland from aridness, it is set to the base direction of conservation and management as main schemes. Moreover, we have suggested that setting the vegetation conservation and management area which considering a ecological vegetation characteristics, managing the ecotone vegetation, setting the buffer zone for protection of ecological core areas, protecting the mountainous wetland indicator species and designating the management vegetation. In conclusion, in order to sustain and maintain a soundly wetland ecosystem, it needs to several management of wetlands damage factors. 1) suppression of the excessive groundwater to basin, 2) stabilization of wetland via hydrologic storage, 3) suppression of changing and transforming wetland into forest by succession via management of xerophytic plants.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.2
• /
• pp.182-206
• /
• 2003

Statement of problem : Successful osseointegration of endosseous threaded implants is dependent on many factors. These may include the surface characteristics and gross geometry of implants, the quality and quantity of bone where implants are placed, and the magnitude and direction of stress in functional occlusion. Therefore clinical quantitative measurement of primary stability at placement and functional state of implant may play a role in prediction of possible clinical symptoms and the renovation of implant geometry, types and surface characteristic according to each patients conditions. Ultimately, it may increase success rate of implants. Purpose : Many available non-invasive techniques used for the clinical measurement of implant stability and osseointegration include percussion, radiography, the $Periotest^{(R)}$, Dental Fine $Tester^{(R)}$ and so on. There is, however, relatively little research undertaken to standardize quantitative measurement of stability of implant and osseointegration due to the various clinical applications performed by each individual operator. Therefore, in order to develop non-invasive experimental method to measure stability of implant quantitatively, the resonance frequency analyzer to measure the natural frequency of specific substance was developed in the procedure of this study. Material & method : To test the stability of the resonance frequency analyzer developed in this study, following methods and materials were used : 1) In-vitro study: the implant was placed in both epoxy resin of which physical properties are similar to the bone stiffness of human and fresh cow rib bone specimen. Then the resonance frequency values of them were measured and analyzed. In an attempt to test the reliability of the data gathered with the resonance frequency analyzer, comparative analysis with the data from the Periotest was conducted. 2) In-vivo study: the implants were inserted into the tibiae of 10 New Zealand rabbits and the resonance frequency value of them with connected abutments at healing time are measured immediately after insertion and gauged every 4 weeks for 16 weeks. Results : Results from these studies were such as follows : The same length implants placed in Hot Melt showed the repetitive resonance frequency values. As the length of abutment increased, the resonance frequency value changed significantly (p<0.01). As the thickness of transducer increased in order of 0.5, 1.0 and 2.0 mm, the resonance frequency value significantly increased (p<0.05). The implants placed in PL-2 and epoxy resin with different exposure degree resulted in the increase of resonance frequency value as the exposure degree of implants and the length of abutment decreased. In comparative experiment based on physical properties, as the thickness of transducer increased, the resonance frequency value increased significantly(p<0.01). As the stiffness of substances where implants were placed increased, and the effective length of implants decreased, the resonance frequencies value increased significantly (p<0.05). In the experiment with cow rib bone specimen, the increase of the length of abutment resulted in significant difference between the results from resonance frequency analyzer and the $Periotest^{(R)}$. There was no difference with significant meaning in the comparison based on the direction of measurement between the resonance frequency value and the $Periotest^{(R)}$ value (p<0.05). In-vivo experiment resulted in repetitive patternes of resonance frequency. As the time elapsed, the resonance frequency value increased significantly with the exception of 4th and 8th week (p<0.05). Conclusion : The development of resonance frequency analyzer is an attempt to standardize the quantitative measurement of stability of implant and osseointegration and compensate for the reliability of data from other non-invasive measuring devices It is considered that further research is needed to improve the efficiency of clinical application of resonance frequency analyzer. In addition, further investigation is warranted on the standardized quantitative analysis of the stability of implant.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2003.04a
• /
• pp.61-62
• /
• 2003

Clonal propagation of high-value forest trees through somatic embryogenesis (SE) has the potential to rapidly capture the benefits of breeding or genetic engineering programs and to improve raw material uniformity and quality. A major barrier to the commercialization of this technology is the low quality of the resulting embryos. Several factors limit commercialization of SE for Corsican pine, including low initiation rates, low culture survival, culture decline causing low or no embryo production, and inability of somatic embryos to fully mature, resulting in low germination and reduced vigour of somatic seedlings. The objective was to develop a Corsican pine maturation medium that would produce cotyledonary embryos capable of germination. Treatments were arranged in a completely randomized design. Data were analyzed by analysis of variance, and significant differences between treatments determined by multiple range test at P=0.05. Corsican pine (Pinus nigra var. maritima) cultures were initiated on modified !P6 medium. Modifications of the same media were used for culture multiplication and maintenance. Embryogenic cultures were maintained on the same medium semi solidified with 2.5 g/l Gelrite. A maturation medium, capable of promoting the development of Corsican pine somatic embryos that can germinate, is a combination of iP6 modified salts, 2% maltose, 13% polyethylene glycol (PEG), 5 mg!l abscisic acid (ABA), and 2.5 g/l Gelrite. After initiation and once enough tissue developed they were grown in liquid medium. Embryogenic cell suspensions were established by adding 0.951.05 g of 10- to 14-day-old semisolid-grown embryogenic tissue to 9 ml of liquid maintenance media in a 250ml Erlenmeyer flask. Cultures were then incubated in the dark at 2022$^{\circ}$C and rotated at 120 rpm. After 2.53 months on maturation medium, somatic embryos were selected that exhibited normal embryo shape. Ten embryos were placed horizontally on 20 ml of either germination medium ($\frac{2}{1}$strength Murashige and Skoog (1962) salts with 2.5 g/l activated charcoal) or same medium with copper sulphate adjusted to 0.25 mg/1 to compensate for copper adsorption by activated carbon. 2% and 4% maltose was substituted by 7.5% and 13% PEG respectively to improve the yield of the embryos. Substitution of' maltose with PEG was clearly beneficial to embryo development. When 2% of the maltose was replaced with 7.5% PEG, many embryos developed to large bullet-shaped embryos. At latter stages of development most embryos callused and stopped development. A few short, barrel-shaped cotyledonary embryos formed that were covered by callus on the sides and base. When 4% of the maltose was removed and substituted with 13% PEG, the embryos developed further, emerging from the callus and increasing yield slightly. Microscopic examination of the cultures showed differing morphologies, varying from mostly single cells or clumps to well-formed somatic embryos that resembled early zygotic embryos only liquid cultures with organized early-stag. A procedure for converting and acclimating germinants to growth in soil and greenhouse conditions is also tested. Seedling conversion and growth were highly related to the quality of the germinant at the time of planting. Germinants with larger shoots, longer, straighter hypocotyls and longer roots performed best. When mature zygotic embryos germinate the root emerges, before or coincident with the shoot. In contrast, somatic embryos germinate in reverse sequence, with the cotyledons greening first, then shoot emergence and then, much later, if at all, the appearance of the root. Somatic seedlings, produced from the maturation medium, showed 100% survival when planted in a field setting. Somatic seedlings showed normal yearly growth relative to standard seedlings from natural seed.