• Nuclear Engineering and Technology
• /
• v.38 no.7
• /
• pp.619-638
• /
• 2006

Low temperature irradiation can significantly harden metallic materials and often lead to strain localization and ductility loss in deformation. This paper provides a review on the radiation effects on the deformation of metallic materials, focusing on microscopic and macroscopic strain localization phenomena. The types of microscopic strain localization often observed in irradiated materials are dislocation channeling and deformation twinning, in which dislocation glides are evenly distributed and well confined in the narrow bands, usually a fraction of a micron wide. Dislocation channeling is a common strain localization mechanism observed virtually in all irradiated metallic materials with ductility, while deformation twinning is an alternative localization mechanism occurring only in low stacking fault energy(SFE) materials. In some high stacking fault energy materials where cross slip is easy, curved and widening channels can be formed depending on dose and stress state. Irradiation also prompts macroscopic strain localization (or plastic instability). It is shown that the plastic instability stress and true fracture stress are nearly independent of irradiation dose if there is no radiation-induced phase change or embrittlement. A newly proposed plastic Instability criterion is that the metals after irradiation show necking at yield when the yield stress exceeds the dose-independent plastic instability stress. There is no evident relationship between the microscopic and macroscopic strain localizations; which is explained by the long-range back-stress hardening. It is proposed that the microscopic strain localization is a generalized phenomenon occurring at high stress.

• Nuclear Engineering and Technology
• /
• v.53 no.9
• /
• pp.2847-2858
• /
• 2021

When a nuclear reactor with rectangular fuel assemblies runs for a long time, impurities and debris may be taken into coolant channels, which may cause flow blockage, and the blocked fuel assemblies might be destroyed. Therefore, the purpose of this study is to perform a thermal-hydraulic analysis of a rectangular fuel assembly by STAR-CCM+, under the condition of one subchannel with 80% blockage ratio. A rectangular fuel assembly of the International Atomic Energy Agency (IAEA) 10 MW material test reactor (MTR) is chosen. In view of the gasket material taken into the coolant channel is close to the single side of the coolant channel, in the flow blockage accident of the Oak Ridge Research Reactor (ORRR), a new blockage category called single side blockage is attempted. The blockage positions include inlet, middle and outlet, and the blockage is set as a cuboid. It is found by simulations that the blockage redistributes the mass flow rate, and large vortices appear locally. The peak temperature of the cladding is maximum, when the blockage is located at the single side of the coolant channel inlet, and no boiling occurs in all blockage cases. Moreover, as the height of the blockage increases, the damage caused by the blockage increases slightly.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.27 no.4
• /
• pp.452-461
• /
• 1982

Average yield of wheat and barley cultivars has been increased 3 percent every year by varietal improvement. The major characteristic changes of those improved cultivars were the early maturing and lodging resistance using dwarf genes, 70-90cm of culm length appearances, under the heavy fertilizer application. Looking back the cultural practices of wheat and barley for the last 20 years, the introduction of early maturing and lodging resistance cultivars around 1970 brought the changes of seeding rate from 65kg to 130- 200kg per hector and the tillering increased by heavy fertilizer. The utilization of livestock and man power for preparation of seedbed were gradually disappeared by increasing agricultural mechanization. The narrow-spaced seeding $(40cm {\times} l8cm)$ and drill seeding $(20cm {\times} 5cm)$ in upland, broadcasting or drilling on high ridge $(120cm {\times} 90cm)$ with the power-toller and whole area broadcasting in paddy field were improved as the main cultural method. The use of agricultural machineries reduced the labour consumption of 940 man hours to 180 man hours per hector from seeding to harvest.

• Journal of the Korean Geophysical Society
• /
• v.9 no.4
• /
• pp.443-453
• /
• 2006

Using seismic profiles obtained in the Antarctic Peninsula continental margin around Smith Island located at the southwestern end of the South Shetland Islands, we investigated sediments distribution, sedimentation, continental shelf formation, and tectonic evolution history. The study area is a very unique area that has two tectonic provinces with a tectonic boundary near Smith Island just the landward projection of the Hero Fracture Zone (HFZ). To the southwest of the Island, the margin became inactive margin after the collision of the ridge crest of the Antarctic-Phoenix ridge and trench, whereas to the northeast the margin is still apparently active margin with the spreading center and trench morphology in the sea. Generally the northeastern margin has the shelf sedimentary basins wth thick sedimentary layers, well-developed forearc basin, broad continental slope and distinct trench morphology, and the southwestern margin is characterized by steep and narrow continental slope and localized shelf basins. the mid-shelf basement high structures are distinct in the southwestern margin, which are thought to be formed by thermal effect caused by the subducted spreading centers. The high is observed in the area just northeast of the Island, implying that the tectonic boundary along the landward projection of the HFZ is not sharply defined.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.12
• /
• pp.1198-1204
• /
• 2013

As a microwave near field probe for near field scanning optical microscope(NSOM) system, H-shaped(ridge type) small aperture is proposed and its performances from the viewpoints of the transmission efficiency(transmission cross section) and spatial confinement(beam spot size) are compared with those of the previous narrow rectangular aperture type. While the transmission efficiencies are comparable to each other for the two structures, the transmitted beam spot size for the proposed H-shaped aperture is much smaller than that for the previous rectangular aperture. This strong point of the H-shaped aperture is expected to significantly improve near-field optical applications such as optical data storage, nanolithography and nanomicroscopy. It is also observed that the transmission efficiency can be improved if the coupling aperture is implemented in the type of the transmission cavity.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.47-54
• /
• 2020

Integration of active and passive waveguides is an essential component of the photonic integrated circuit and its elements. Butt joint is one of the important technologies to accomplish it with significant advantages. However, it suffers from high optical loss at the butt joint junction and need of accurate process control to align both waveguides. In this study, we used beam propagation method to simulate an integrated device composed of a laser diode and spot size converter (SSC). Two SSCs with different mode properties were combined with laser waveguide and optical coupling efficiency was simulated. The SSC with larger near field mode showed lower coupling efficiency, however its far field pattern was narrower and more symmetric. Tapered passive waveguide was utilized for enhancing the coupling efficiency and tolerance of waveguide offset at the butt joint without degrading the far field pattern. With this technique, high optical coupling efficiency of 89.6% with narrow far field divergence angle of 16°×16° was obtained.

• Journal of architectural history
• /
• v.31 no.6
• /
• pp.59-68
• /
• 2022

This paper is an architectural historical study on Chimi of Hwangnyongsa Temple. In this research, the shape and cross-section of the chimi are reviewed. The results of the study are as follows. The chimi is a form in which the head part facing the maru is omitted, and the upper and lower body are separated. The upper and lower bonds are assembled into a two types of joint throughout the side of the torso, and then bound with an iron strap. Because of the absence of ridge line in the front, and the narrow curved surface which makes the side plate close to the plane, the entire cross-section is triangular, and the rear plate maintains the shape of the chimi. The naerimmaru connected to the side of the chimi has a slope, so it is clear that the chimi was used on the woojingak-jibung(hipped-roof), and the wing part and back of the chimi are erected on the side roof. The height of the yongmaru and chunyeomaru is about the same and the roofing tiles of those are in contact. The roofing tiles of chunyemaru should be cut to fit the angle of the contacting part. The maru is 30 stories high of roofing tiles as a result of the on-board survey. Based on reference on the shape and timing of the production of chimi, the height of chimi, and the maru is believed to have been built before the Unified Silla Period and used in buildings with at least seven-kan frontage. Buildings corresponding to these construction conditions can be seen as Central hall and East hall in Hwangnyongsa temple.

• The Journal of Korean Academy of Prosthodontics
• /
• v.54 no.3
• /
• pp.267-272
• /
• 2016

This case report describes the treatment of two fully edentulous patients with mini-implant overdentures using different implant systems on narrow mandibular alveolar bone ridge. They were complaining about discomfort and pain wearing mandibular conventional complete dentures caused by insufficient retention. Each patient received four miniimplants in the interforaminal area of the mandible using the non-submerged flapless surgical approach. One-body type implant (Slimline, Dentium, Seoul, Korea) was used for a patient and loaded immediately after surgery. Metal housings of O-ring were attached by direct technique. For the other patient, two-piece type implant (LODI, Zest Anchors, Escondido, CA, USA) was used and impressions were made for attachment connection of the Locator's metal housings after 8 weeks of surgery. Within this case report, mandibular miniimplant overdentures using different implant systems showed improvement of patient satisfaction with favorable peri-implant tissue response 6 months after attachment connection. However, long-term follow-up is needed for further evaluation.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.37
• /
• pp.2.1-2.9
• /
• 2015

Background: The aim of this study was to evaluate the effect of autogenous tooth bone as a graft material for regeneration of bone in vertical bony defects of the minipigs. Material and Methods: Six minipigs were used in this study. Four molars were extracted in the right mandibular dentition and sent to the Korea Tooth Bank for fabrication of autogenous tooth bone. Ten days later, each extraction site was implanted with MS Implant Narrow Ridge $3.0{\times}10mm$ fixture (Osstem, Seoul, Korea) after standardized 2mm-sized artificial vertical bony defect formation. Pineappleshaped Root-On type autogenous tooth bones were applied to the vertical defects around the neck area of the posterior three fixtures and the fore-most one was not applied with autogenous bone as a control group. Each minipig was sacrificed at 4, 8, 12 weeks after fixture installation and examined radiologically and histologically. Histological evaluation was done under light microscope with Villanueva osteochrome bone staining with semi-quantitative histomorphometric study. Percentage of new bone over total area (NBF) and bone to implant contact (BIC) ratio were evaluated using digital software for area calculation. Result: NBF were $48.15{\pm}18.02%$, $45.50{\pm}28.37%$, and $77.13{\pm}15.30%$ in 4, 8, and 12 weeks, respectively for experimental groups. The control group showed $37.00{\pm}11.53%$, $32.25{\pm}26.99%$, and $1.33{\pm}2.31%$ in 4,8,12 weeks, respectively. BIC ratio were $53.08{\pm}19.82%$, $45.00{\pm}28.37%$, and $75.13{\pm}16.55%$ in 4,8,12 weeks, respectively. Those for the control groups were $38.33{\pm}6.43%$, $33.50{\pm}29.51%$, and $1.33{\pm}2.31%$ in 4, 8, 12 weeks, respectively. Conclusion: Autogenous tooth bone showed higher score than control group in NBF and BIC in all the data encompassing 4,8,12 weeks specimens, but statistically significant only 12 weeks data in both NBF and BIC.

• Economic and Environmental Geology
• /
• v.18 no.4
• /
• pp.369-379
• /
• 1985

The geological structures and some of the stratigraphy in the area studied are being thought to be ambiguous and controvertible. The present study intended to clarify these ambiguities by correct interpretation of the geological structures and lithostratigraphy of the area concerned. The so-called "Sambangsan formation", which was designated as an unknown age by the Taebaksan Geological Investigation Corps (1962) and as the mid Cambrian age by T. Kobayashi (1966) and I.S. Kim (1983), has been determined by the present study as the $Hongj{\breve{o}}m$ series of Carbo-Permian age resting unconformably on the Cambro-Ordovician limestone formations. This determination was supported by conodont study concurrently carried out by I.S.Kim. The so-called "Daehari formation", which was renamed by the later study group after the original "Sambangsan formation" distributed in the area from southwest of Sambangsan toward southwest to $Juch{\breve{o}}n$, possesses more or less the same lithlogy as "Sambangsan formation" of the old designation in the eastern of the area, but different lithology in the western localities where Sadong formation, the basal sandstone member of the Kobangsan formation and the green shale member of the Nokam formation are cropped out. The narrow belt of the complex mixture of the $Py{\breve{o}}ngan$ group in-between limestone formations extending over 16km with a width of 500m to 1000m was formed by the faults: the northern boundary with the limestone formations is a fault contact all the way through entire area and the southern boundary is either fault contact in most of the area and unconformity in some other area. The $Hongj{\breve{o}}m$ formation on the Mt. Sambangsan shows rather steeply dipping nearly isoclinal folds which plunges $10^{\circ}$ to $20^{\circ}$ southward. There are also field evidences that the limestone formations distributed in both north and south of the Hongjom formation (erstwhile "Sambangsan formation") along the Sambangsan ridge are the same formations and show the same folding as the $Hongj{\breve{o}}m$ formation. Therefore, these limestone formations should be rezoned in the light of the new structural interpretation although they were differently designated in the previous studies as $Py{\breve{o}}ngchang$ and $Y{\breve{o}}ngw{\breve{o}}l$-type of the Joson Group. The structures developed in the area mostly faults, which acted as one of the guides for the new interpretation of the geology and structure of the area are described and shown on the geologic map.