• Journal of Powder Materials
• /
• v.28 no.1
• /
• pp.44-50
• /
• 2021

Zinc selenide (ZnSe) nanoparticles were synthesized in aqueous solution using glutathione (GSH) as a ligand. The influence of the ligand content, reaction temperature, and hydroxyl ion concentration (pH) on the fabrication of the ZnSe particles was investigated. The optical properties of the synthesized ZnSe particles were characterized using various analytical techniques. The nanoparticles absorbed UV-vis light in the range of 350-400 nm, which is shorter than the absorption wavelength of bulk ZnSe particles (460 nm). The lowest ligand concentration for achieving good light absorption and emission properties was 0.6 mmol. The reaction temperature had an impact on the emission properties; photoluminescence spectroscopic analysis showed that the photo-discharge characteristics were greatly enhanced at high temperatures. These discharge characteristics were also affected by the hydroxyl ion concentration in solution; at pH 13, sound emission characteristics were observed, even at a low temperature of 25℃. The manufactured nanoparticles showed excellent light absorption and emission properties, suggesting the possibility of fabricating ZnSe QDs in aqueous solutions at low temperatures.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.4
• /
• pp.219-226
• /
• 2023

Utilizing low-dimensional structures of oxide semiconductors is a promising approach to fabricate relevant gas sensors by means of potential enhancement in surface-to-volume ratios of their sensing materials. In this work, vertically aligned cupric oxide (CuO) nanorods are successfully synthesized on a transparent glass substrate via seed-mediated hydrothermal synthesis method with the use of a CuO nanoparticle seed layer, which is formed by thermally oxidizing a sputtered Cu metal film. Structural and optical characterization by x-ray diffraction (XRD), scanning electron microscopy (SEM), and Raman spectroscopy reveals the successful preparation of the CuO nanorods array of the single monoclinic tenorite crystalline phase. From gas sensing measurements for the nitrogen monoxide (NO) gas, the vertically aligned CuO nanorod array is observed to have a highly responsive sensitivity to NO gas at relatively low concentrations and operating temperatures, especially showing a high maximum sensitivity to NO at 200 ℃ and a low NO detection limit of 2 ppm in dry air. These results along with a facile fabrication process demonstrate that the CuO nanorods synthesized on a transparent glass substrate are very promising for low-cost and high-performance NO gas sensors.

• Journal of Adhesion and Interface
• /
• v.20 no.1
• /
• pp.23-28
• /
• 2019

In this study, the micro- and nano-particles were used and their shapes were transferred into the polydimethylsiloxane (PDMS) film to fabricate the dry adhesives and their properties were investigated. The Cu nanoparticles of the sizes of 20 nm, 40 nm and 70 nm and the polymethylmethacrylate (PMMA) beads of the size of $5{\mu}m$ were used to transfer their images and the resultant properties of the dry adhesives were compared. The effects of particle size and materials on the mechanical property, tensile adhesion strength, light transmittance, surface morphology, water contact angle were studied. The dry adhesives obtained from the transfer process of Cu nanoparticles with the size of 20 nm resulted in the enhancement of tensile adhesion strength more than 300% compared to that of the bare PDMS. The formation of nanostructure of large surface area on the surface of the PDMS film by the Cu nanoparticles may responsible for the improvement. This study suggests that the use of nanoparticles during the fabrication of PDMS dry adhesives is easy and effective and could be applied to the fabrication of the medical patch.

• Journal of Adhesion and Interface
• /
• v.21 no.4
• /
• pp.143-155
• /
• 2020

Hydrophobic Organic-Inorganic (O-I) hybrid materials prepared by sol-gel process have been widely used at functional coating fields such as coatings for anti-corrosion, anti-icing, self-cleaning, anti-reflection. The key point for fabricating hydrophobic surface is to optimize the surface energy and roughness of the coating films. There are typical processes to control the surface energy and roughness which are 'In situ fabricating', 'Pre-fluorinating/Post-roughening', 'Pre-roughening/ Post-fluorinating'. In this study, particle-binder process was used for in-situ fabrication of hydrophobic coating films. Various O-I hybrid compounds prepared using several kinds of alkoxysilane compounds were used as a binder for silica nanoparticles at particle-binder process. To study effect of fluorine content and weight ratio of particle : binder on the hydrophobicity and surface morphology, Hydrophobic coating films were prepared onto glass substrate at various content of fluorine content of O-I hybrid binder and weight ratio of particle : binder. The coating films prepared using O-I hybrid binder (GPTi-HF10) having 10 wt% of fluorine content showed the highes water contact angle (107.52±1.6°). The coating films prepared at 1:3 weight ratio of GPTi-HF10 : silica nanoparticle exhibited the highest water contact angle (130.84±1.99°).

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.2
• /
• pp.39-46
• /
• 2013

In this paper, organic solar cells(OSCs) based on bulk-heterojunction structures were fabricated by spin coating method using polymer P3HT and fullerene PCBM as a photoactive layer. The fabricated OSCs had a simple glass/ITO/PEDOT:PSS/P3HT:PCBM/Al structures. The photoactive layer of mixed P3HT:PCBM was formed with 1:1 weight ratio. The hole transport layer(HTL) was used conducting polymer PEDOT:PSS concentration with gold nanoparticles. The annealing temperature and concentration of nanoparticles in HTL were verified to improve the OSC characterization. The percentage of gold nanoparticles in HTL were 0.5 wt% and 1.0 wt%, and the surface morphology, electrical properties and absorption intensities were investigated. The devices were 0.5 wt%, and the highest 3.1% of the powder conversion efficiency(PCE), 10.2 $mA/cm^2$ of the maximum short circuit current density($J_{SC}$), 0.535V of the open circuit voltage($V_{OC}$) and 55.8% of the fill factor(F.F) could be obtained when the nanoparticle concertration was 0.5 wt%. The annealing temperature of HTL was $110^{\circ}C$, $130^{\circ}C$, $150^{\circ}C$ in vacuum oven and measured the absorption intensities, surface morphology, crystallinity and electrical properties were investigated. The best property was obtained in HTL annealed at $130^{\circ}C$ for gold nanoparticles of 0.5 wt%, showing that $J_{SC}$, $V_{OC}$, F.F and PCE were about 12.0 $mA/cm^2$, 0.525V, 64.2% and 4.0%, respectively.

• Journal of the Korean Chemical Society
• /
• v.59 no.1
• /
• pp.36-44
• /
• 2015

This article describes synthesis and electrochemical properties of layer-by-layer self-assembled multilayer film composed of polyaniline (PANi), graphene oxide (GO) and phytic acid (PA), whereby the GO was electrochemically reduced to ERGO, resulting in $(PANi/ERGO/PANi/PA)_{10}$ film electrode. Especially, we examined the possibility to improve the volumetric capacitive property of $(PANi/ERGO)_{20}$ film electrode via combining a spherical hexakisphosphate PA nanoparticle into the multilayer film that would dope PANi properly and also increase the porosity and surface area of the electrode. The electrochemical performances of the multilayer film electrodes were investigated using a three-electrode configuration in 1 M $H_2SO_4$ electrolyte. As a result, the $(PANi/ERGO)_{20}$ electrode showed the volumetric capacitance of $666F/cm^3$ at a current density of $1A/cm^3$, which was improved to the volumetric capacitance of $769F/cm^3$ for the $(PANi/ERGO/PANi/PA)_{10}$ electrode, in addition to the cycling stability maintained to 79.3% of initial capacitance after 1000 cycles. Thus, the electrochemical characteristics of the $(PANi/ERGO)_{20}$ electrode, which was densely packed by ${\pi}-{\pi}$ stacking between the electron-rich conjugate components, could have been improved through structural modification of the multilayer film via combining a spherical hexakisphosphate PA nanoparticle into the multilayer film.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.55-55
• /
• 2015

Today, engineers are facing new set of challenges that are quite different from the conventional ones. Information technologies are rapidly commoditizing while the paths beyond the current roadmaps became uncertain as various technologies have been pushed to their limits. Along with these changes in IT ecosystems, grand challenges such as global security, health, sustainability, and energy increasingly require trans-disciplinary solutions that go beyond the traditional arenas in STEM (Science, Technology, Engineering and Mathematics). Addressing these needs is shifting engineering education and research to a new paradigm where the emphasis is placed on the consilience for holistic and system level understanding and the convergence of technology with AHSD (arts, humanities, social science, and design). At the center of this evolutionary convergence, nanotechnologies are enabling novel functionalities such as bio-compatibility, flexibility, low power, and sustainability while on a mission to meet scalability and low cost for smart electronics, u-health, sensing networks, and self-sustainable energy systems. This talk introduces the efforts of convergence based on the emerging nano technology tool sets in the newly launched School of Integrated Technology and the Yonsei Institute of Convergence Technology at Yonsei International Campus. While the conventional devices have largely depended upon the inherent material properties, the newer devices are enabled by nanoscale dimensions and structures in increasingly standardized and scalable fabrication platform. Localized surface plasmon resonance in 0 dimensional nano particles and structures leads to subwavelength confinement and enhanced near-field interactions enabling novel field of metal photonics for sensing and integrated photonic applications [1,2]. Unique properties offered by 1 dimensional nanowires and 2 dimensional materials and structures can enable novel electronic, photonic, nano-bio, and biomimetic applications [3-5]. These novel functionalities offered by the emerging nanotechnologies are continuously finding pathways to be part of smart systems to improve the overall quality of life.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.11
• /
• pp.1767-1778
• /
• 2010

This study investigates applying $TiO_2$ (titanium dioxide) nanoparticles to polypropylene nonwoven fabrics via electrospinning for the development of UV-protective materials. To fabricate uniform nanocomposite fibers, three types of $TiO_2$ nanoparticles were applied: powder, colloid, and $TiO_2$ coated polymer pellets. $TiO_2$/polyurethane (PU) and $TiO_2$/poly(vinyl alcohol) (PVA) nanocomposite fibers were electrospun and the morphology was examined using a field-emission scanning electron microscope and a transmission electron microscope. Layered fabric systems with electrospun $TiO_2$ nanocomposite fiber webs were developed at various concentrations of $TiO_2$ in a range of the web area density. The effects of $TiO_2$ concentration and web area density on UV-protective properties were examined. When $TiO_2$ colloid was added into a PVA polymer solution, uniform nanocomposite fiber webs in which $TiO_2$ particles were evenly dispersed were produced. Water-soluble PVA nanofiber webs were given a heat treatment to stabilize the electrospun PVA fibrous structure against dissolution in water. $TiO_2$/PVA nanoeomposite fiber webs with 2wt% $TiO_2$ and 3.0g/$m^2$ web area density exhibited an ultraviolet protection factor of greater than 50, indicating excellent UV protection.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.5
• /
• pp.377-383
• /
• 2014

An addressable conducting network (ACN) makes it possible to monitor the condition of a structure using the electrical resistance between electrodes on the surface of a carbon fiber reinforced plastics (CFRP) structure. To improve the damage detection reliability of the ACN, the contact resistances between the electrodes and CFRP laminates needs to be minimized. In this study, silver nanoparticle electrodes were fabricated via printed electronics techniques on a CFRP composite. The contact resistance between the silver electrodes and CFRP were measured with respect to various fabrication conditions such as the sintering temperature of the silver nano-ink and the surface roughness of the CFRP laminates. The interfaces between the silver electrode and carbon fibers were observed using a scanning electron microscope (SEM). Based on this study, it was found that the lowest contact resistance of $0.3664{\Omega}$ could be achieved when the sintering temperature of the silver nano-ink and surface roughness were $120^{\circ}C$ and 0.230 a, respectively.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.1.1-1.1
• /
• 2011

Printed electronics based on the direct writing of solution processable functional materials have been of paramount interest and importance. In this talk, the synthesis of printable inorganic functional materials (conductors and semiconductors) for thin-film transistors (TFTs) and photovoltaic devices, device fabrication based on a printing technique, and specific characteristics of devices are presented. For printable conductor materials, Ag ink is designed to achieve the long-term dispersion stability and good adhesion property on a glass substrate, and Cu ink is sophisticatedly formulated to endow the oxidation stability in air and even aqueous solvent system. The both inks were successfully printed onto either polymer or glass substrate, exhibiting the superior conductivity comparable to that of bulk one. In addition, the organic thin-film transistor based on the printed metal source/drain electrode exhibits the electrical performance comparable to that of a transistor based on a vacuum deposited Au electrode. For printable amorphous oxide semiconductors (AOSs), I introduce the noble ways to resolve the critical problems, a high processing temperature above $400^{\circ}C$ and low mobility of AOSs annealed at a low temperature below $400^{\circ}C$. The dependency of TFT performances on the chemical structure of AOSs is compared and contrasted to clarify which factor should be considered to realize the low temperature annealed, high performance AOSs. For photovoltaic application, CI(G)S nanoparticle ink for solution processable high performance solar cells is presented. By overcoming the critical drawbacks of conventional solution processed CI(G)S absorber layers, the device quality dense CI(G)S layer is obtained, affording 7.3% efficiency CI(G)S photovoltaic device.