• Journal of Powder Materials
• /
• v.20 no.2
• /
• pp.120-124
• /
• 2013

This study is carried out to develop the new process for the fabrication of ultra-fine electrodes on the flexible substrates using superhydrophobic effect. A facile method was developed to form the ultra-fine trenches on the flexible substrates treated by plasma etching and to print the fine metal electrodes using conductive nano-ink. Various plasma etching conditions were investigated for the hydrophobic surface treatment of flexible polyimide (PI) films. The micro-trench on the hydrophobic PI film fabricated under optimized conditions was obtained by mechanical scratching, which gave the hydrophilic property only to the trench area. Finally, the patterning by selective deposition of ink materials was performed using the conductive silver nano-ink. The interface between the conductive nanoparticles and the flexible substrates were characterized by scanning electron microscope. The increase of the sintering temperature and metal concentration of ink caused the reduction of electrical resistance. The sintering temperature lower than $200^{\circ}C$ resulted in good interfacial bonding between Ag electrode and PI film substrate.

• Journal of Powder Materials
• /
• v.23 no.4
• /
• pp.317-324
• /
• 2016

Tin is one of the most promising anode materials for next-generation lithium-ion batteries with a high energy density. However, the commercialization of tin-based anodes is still hindered due to the large volume change (over 260%) upon lithiation/delithiation cycling. To solve the problem, many efforts have been focused on enhancing structural stability of tin particles in electrodes. In this work, we synthesize tin nano-powders with an amorphous carbon layer on the surface and surroundings of the powder by electrical wire explosion in alcohol-based liquid media at room temperature. The morphology and microstructures of the powders are characterized by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and transmission electron microscopy. The electrochemical properties of the powder for use as an anode material for lithium-ion battery are evaluated by cyclic voltammetry and a galvanometric discharge-charge method. It is shown that the carbon-coated tin nano-powders prepared in hexanol media exhibit a high initial charge specific capacity of 902 mAh/g and a high capacity retention of 89% after 50 cycles.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.5
• /
• pp.467-473
• /
• 2019

In this study, approached to improve durability of the multi-functional nano-pattern fabricated on the curved lens surface using nanoimprint lithography (NIL) was proposed, and the effects of the proposed methods on functionality after wear test were examined. To improve the mechanical property of ultraviolet(UV)-curable resin, UV-NIL was conducted at the elevated temperature around $60^{\circ}C$. In addition, micro/nano hierarchical structures was fabricated on the lens surface with a durable film mold. Analysis on the worn surfaces of nano-hole pattern and hierarchical structures and measurements on the static water contact angle and critical water volume for roll-off indicated that the UV curing process with elevated temperature is effective to maintain wettability by increasing hardness of resin. Also, it was found that the micro-scale pattern is effective to protect nano-pattern from damage during wear test.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.1
• /
• pp.31-37
• /
• 2021

Sn-3wt%Ag-0.5wt%Cu (SAC305) solder is most popular solder in electronics industry. However, SAC305 has also drawbacks such as growth of β-Sn phase, intermetallic compounds (IMCs) of Ag3Sn, Cu6Sn5 and Cu3Sn which can result in deterioration of solder joints in terms of metallurgically, mechanically and electrically. Thus, improvement of SAC305 solders have been investigated continuously by addition of alloying elements, nano-particles and etc. In this paper, recent improvements of SAC solders including nano-composite alloys and related solderabilty and metallurgical and mechanical properties are investigated.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.8
• /
• pp.749-754
• /
• 2008

A large number of studies on the various characteristics of epoxy-layered silicate nanocomposites, such as electric and mechanical, morphology have been conducted and contributed to improve their characteristics. However, studies on the effects of its thermal conductivities in the thermal properties are not enough, even though there are some excellent evaluations for its insulation performances. Thermal properties will cause thermal degradation and significantly affect the reliability of these epoxy-layered silicate nanocomposites. In the results of the analysis of epoxy-layered silicate nanocomposites $T_g$ for various types of organoclays (10A, 15A, 20A, 30B, and 93A), it showed an excellent thermal property of 10A. Also, it represented low values in storage modulus and mechanical Tan (Delta) at a high temperature section 140$^{\circ}C$ and excellent thermal properties due to its movement to the high temperature section in the case of the property of 10A in the measurement of DMA elastics and mechanical losses. In the results of the measurement of thermal conductivities, power ultrasonic applications represented a significant increase in thermal conductivities in the case of the applications of power ultrasonic and planetary centrifugal mixers. Based on these results, it is necessary to perform related studies because it can be applied as useful materials for future power facilities applications in mold and impregnate insulation.

• Korean Journal of Materials Research
• /
• v.17 no.9
• /
• pp.480-483
• /
• 2007

Hydroxyapatites were prepared by the different $SiO_2$ addition at $1450^{\circ}C$ for 2h. With the increase of $SiO_2$ addition, microstructure, bulk density, porosity, mechanical strength of $hydroxyapatite/{\beta}-TCP$ composite were investigated. When the sintered HAp contained 1 wt% $SiO_2$, the each properties of the HAp were increased. But the excess addition of $SiO_2$ content above 1wt% the each property were decreased. This results were due to the ${\beta}-TCP$ phase. The ${\beta}-TCP$ phase appeared at 3 wt% $SiO_2$ addition and the ${\beta}-TCP$ phase was enhanced by the $SiO_2$ increasing.

• Polymer(Korea)
• /
• v.35 no.3
• /
• pp.189-195
• /
• 2011

The design of new bioactive scaffolds offering physiologic environment for tissue formation is an important frontier in biomaterials research. In this study, we performed compressive strength, water-uptake ability, and SEM analysis for physical property assessment of 3-D silk/PLGA scaffold, and investigated the adhesion, proliferation, phenotype maintenance, and inflammatory responses of RAW 264.7 and NIH/3T3 for cell compatibility. Scaffolds were prepared by the solvent casting/salt leaching method and their compressive strength and water-uptake ability were excellent at 20 wt% silk content. Result of cell compatibility assay showed that inflammatory responses distinctly decreased, and initial adhesion and proliferation were maximized at 20 wt% silk content. In conclusion, we suggest that silk/PLGA scaffolds may be useful to tissue engineering applications.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.21-24
• /
• 2003

In general, to enhance physical properties of PET-layered silicate nanocomposites $(P_{et}LSNs)$, it has been well known that the organic modifiers should introduce into gallery regions. However, the organic modifiers in$(P_{et}LSNs)$ may result in thermal decomposition by melt processing at high temperature, and it necessarily lead to deteriorate various physical properties of final products. Therefore, in this study, $(P_{et}LSNs)$ excluding and including organic modifiers were prepared by solution method $(S-P_{et}LSNs_{eom} and S-P_{et}LSNs_{iom})$ and we (focused on the effects of the organic modifiers in $P_{et}$ LSNs with exfoliation structure on the crystallization behaviors, the optical transparency, the thermal stability and the mechanical property. The absence and existence of organic modifiers in $S-P_{et}LSNs_{eom} and S-P_{et}LSNs_{iom}$ were investigated by EA and TGA, and nano-structure of silicate layers in $S-P_{et}LSNs$ was evaluated by using WXRD, SAXS and TEM. $S-P_{et}LSNs_{eom} and S-P_{et}LSNs_{iom}$ were mixed with neat PET as masterbatches by melt method $(M-P_{et}LSNs_{eom} and M-P_{et}LSNs_{iom})$, and also neat PET was mixed with organically modified layered silicates (OLS) by conventional direct melt method $(D-P_{et}LSNs) at 270^{\circ}C$. As results, it was found that $M-P_{et}LSNs_{eom}, M-P_{et}LSNs_{iom}, and D-P_{et}LSN$ showed a exfoliated structure and exhibited faster crystallization rate, better thermal stability and mechanical property than those of neat PET due to the dispersed and detaminated silicate layers in PET matrix. Whereas, considering organic modifiers effect, $M-P_{et}LSNs_{eom} and D-P_{et}LSN$ exhibited slower crystallization rate, poorer optical, thermal and mechanical properties, in comparison to $M-P_{et}LSNs_{eom}> due to the thermal decomposition of organic modifier in $D-P_{et}LSNs$ during melt method.

• Journal of the Korean institute of surface engineering
• /
• v.43 no.6
• /
• pp.255-259
• /
• 2010

In this work, Ni-Co composites incorporated with nano-sized SiC particles in the range of 45-55 nm are prepared by electroplating. The effects of plating duration on the chemical composition, surface morphology, crystalline structures and hardness have been studied. The maximum hardness of Ni-Co-SiC composite coating is approximately 633 Hv at plating duration of 1 h. The hardness is gradually decreased with increasing plating duration, which can be attributed to the growth of crystalline size and the agglomerates of SiC nano-particles. It is therefore explained that the grain refinement of Ni-Co matrix and stable dispersion of SiC particles play an important role for strengthening, which indicate Hall-Petch relation and Orowan model were dominant for hardening of Ni-Co-SiC composite coatings.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1963-1966
• /
• 2008

We fabricate and evaluate the metal-oxide-semiconductor (MOS) transistor probe with the focused-ionbeam (FIB) for surface electric properties. The probes are designed with the rectangular and V-shaped structures, and their dimensions are determined considering the contact mode operation. The conductive nano tip is grown with FIB system, and deposition condition is controlled for the sharp tip. The fabricated device is applied to the various test patterns like the metal lines and PZT poling regions, and the results show the well defined measurement patterns.