• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.90.1-90.1
• /
• 2010

Due to the rapidly diminishing energy sources and higher energy production cost, the interest in dye-sensitized solar cells (DSSCs) has been increasing dramatically in recent years. A typical DSSC is constructed of wide band gap semiconductor electrode such as $TiO_2$ or ZnO that are anchored by light-harvesting sensitizer dyes and surrounded by a liquid electrolyte with a iodide ion/triiodide ion redox couple. DSSCs based on one-dimensional nano-structures, such as ZnO nanorods, have been recently attracting increasing attention due to their excellent electrical conductivity, high optical transmittance, diverse and abundant configurations, direct band gap, absence of toxicity, large exiton binding energy, etc. However, solar-to-electrical conversion performances of DSSCs composed of ZnO n-type photo electrode compared with that of $TiO_2$ are not satisfactory. An important reason for the low photovoltaic performance is the dissolution of $Zn^{2+}$ by the adsorption of acidic dye followed by the formation of agglomerates with dye molecules which could block the I-diffusion pathway into the dye molecule on the ZnO surface. In this paper, we prepared the DSSC with the ZnO electrode using the chemical bath deposition (CBD) method under low temperature condition (< $100^{\circ}C$). It was demonstrated that the ZnO seed layers played an important role on the formation of the ZnO nanostructures using CBD. To achieve truly low-temperature growth of the ZnO nanostructures on the substrates, a two-step method was developed and optimized in the present work. Firstly, ZnO seed layer was prepared on the FTO substrate through the spin-coating method. Secondly, the deposited ZnO seed substrate was immersed into an aqueous solution of 0.25M zinc nitrate hexahydrate and 0.25M hexamethylenetetramine at $90^{\circ}C$ for hydrothermal reaction several times.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.393-393
• /
• 2012

Optically active nanostructures such as subwavelength moth-eye antireflective structures or surface enhanced Raman spectroscopy (SERS) active structures have been demonstrated to provide the effective suppression of unwanted reflections as in subwavelength structure (SWS) or effective enhancement of selective signals as in SERS. While various nanopatterning techniques such as photolithography, electron-beam lithography, wafer level nanoimprinting lithography, and interference lithography can be employed to fabricate these nanostructures, roll-to-roll (R2R) nanoimprinting is gaining interests due to its low cost, continuous, and scalable process. R2R nanoimprinting requires a master to produce a stamp that can be wrapped around a quartz roller for repeated nanoimprinting process. Among many possibilities, two different types of mask can be employed to fabricate optically active nanostructures. One is self-assembled Au nanoparticles on Si substrate by depositing Au film with sputtering followed by annealing process. The other is monolayer silica particles dissolved in ethanol spread on the wafer by spin-coating method. The process is optimized by considering the density of Au and silica nano particles, depth and shape of the patterns. The depth of the pattern can be controlled with dry etch process using reactive ion etching (RIE) with the mixture of SF6 and CHF3. The resultant nanostructures are characterized for their reflectance using UV-Vis-NIR spectrophotometer (Agilent technology, Cary 5000) and for surface morphology using scanning electron microscope (SEM, JEOL JSM-7100F). Once optimized, these optically active nanostructures can be used to replicate with roll-to-roll process or soft lithography for various applications including displays, solar cells, and biosensors.

• 한국축산식품학회지
• /
• 제37권5호
• /
• pp.752-763
• /
• 2017

Marine fish skin peptides (FSP) have been widely studied due to their antioxidant and antimicrobial properties. We aimed to use a natural antioxidant, FSP, to replacing synthetic preservatives in a pork patty model, which is safer for human body. Moreover, nano-liposome technology can be applied for masking the fishy smell and improving the stability of this peptide. Therefore, in this study, the effects of FSP and FSP-loaded liposomes (FSPL) on pork patty were evaluated through the tests of thiobarbituric acid reactive substances (TBARS), color, cooking loss, texture, volatile basic nitrogen (VBN), and the pH value, during 14 d of refrigerated ($4^{\circ}C$) storage. The results showed that all FSP-treated patties had lower TBARS values than control patties, which indicated an inhibitory effect of FSP on lipid oxidation. This effect in the patties depended on the FSP concentration. However, FSPL-treated patties showed significantly higher and undesirable TBARS values compared to the control, and this effect depended on the FSPL concentration. None of the physicochemical results showed remarkable changes except the pH and VBN values. Therefore, this study provides evidence that FSP has great potential to inhibit the lipid oxidation of pork patties and is capable of maintaining the quality and extending the shelf life. However, it is necessary to study the application of FSP treatments greater than 3% to improve the antioxidant effect on pork patties and search for other coating materials and technology to reduce the drawbacks of FSP.

• 접착 및 계면
• /
• 제16권3호
• /
• pp.116-121
• /
• 2015

본 연구에서는 발수성 재료로 쓰이고 상대적으로 가격이 비싼 불소계 실란을 대체하기 위해 octadecyltrichlorosilane (OTS)을 사용하였다. 코팅층의 기계적 접착강도를 향상시키기 위해 무기바인더를 산 촉매 하에서 졸-겔 반응에 의해 분산시켜 합성하였다. 합성된 실리카 나노입자는 나노크기의 거칠기를 제공하기 때문에 초소수성을 쉽게 얻기 어려우므로 유기용매에 의한 입자의 응집을 유도하였다. 실리카 나노입자의 적절한 크기 선택에 따라 OTS를 사용해서 표면을 소수화 시킨 후 유기용매의 양이 증가함에 따라 초소수성의 표면을 얻었고 극도의 물 반발 거동이 zero sliding angle과 함께 관찰되었다. 이러한 초소수성은 용매와의 혼합과 상관없이 유전상수가 25보다 작은 값을 가졌으며 용매 내에서 입자의 응집을 통해 유도된 초소수성 표면을 제조하는 것이 저유전상수 값에 대한 지표가 되었다.

• 한국세라믹학회지
• /
• 제45권9호
• /
• pp.524-530
• /
• 2008

Anti-Reflective (AR) thin film coatings of $SiO_2$ (n= 1.48) and $TiO_2$ (n=2.17) were deposited by ion-beam assisted deposition (IBAD) with End-Hall ion source and conventional electron beam (e-beam) evaporation to investigate the effect of deposition method on the refractive indicies (n) of the fIlms. Green-light generation using a GaAs laser diode was achieved via excitation of the second harmonic. The latter resulted from the transmission of the fundamental guided-mode wave of 1064 nm through periodically poled $LiNbO_3$. Large differences in the refractive indicies of each of the layers in the multilayer coating may improve AR performance. IBAD of $SiO_2$ reduced its refractive index from 1.45 to 1.34 at 1064 nm. Conversely, e-beam evaporation of $TiO_2$ increased its refractive index from 1.80 to 2.11. In addition, no fluctuations in absorption at the wavelength of 1064 nm were found. The results suggest that films prepared by different deposition methods can increase the effectiveness of multilayer AR coatings.

• 한국수소및신에너지학회논문집
• /
• 제21권4호
• /
• pp.271-277
• /
• 2010

$(Ba(Zr_{0.85}Y_{0.15})O_{3-\delta})$ oxide, showing high protonic conductivity at high temperatures and good chemical stability with $CO_2$ are referred to as hydrogen separation membrane. For high efficiency of hydrogen separation ($H_2$ flux and selectivity) and low fabrication cost, ultimate thin and dense BZY-Ni layer has to be coated on a porous substrate such as $ZrO_2$. Aerosol depostion (AD) process is a novel technique to grow ceramic film with high density and nano-crystal structure at room-temperature, and may be applicable to the fabrication process of AD integration ceramic layer effectively. XRD, SEM, X-ray mapping measurements were conducted in order to analyze the characteristics of BZY-Ni membrane fabricated by AD process. it is observed that it is homogeneous distribution for BZY-Ni. The result of $H_2$ permeation rate suggests that BZY-Ni composite is higher than BZY.

• 멤브레인
• /
• 제18권2호
• /
• pp.176-184
• /
• 2008

본 연구에서 졸-겔 방법에 의하여 나노 기공을 가지는 세라믹막을 제조하여 단일 조성의 헬륨과 질소를 가지고 기체투과 실험을 수행하였다. 기공 크기 $0.1{\mu}m$, 기공율 32%의 평막형 ${\alpha}-Al_2O_3$ 지지체를 제조하였으며, 지지체를 담지하여 코팅하는 방법으로 4nm의 기공 크기를 가지는 ${\gamma}-Al_2O_3$ 중간층을 제조하였다. 실리카 졸은 TEOS의 산 촉매 가수분해와 축중합반응을 통하여 합성하였다. 막은 딥코팅과 소결과정을 거쳐 제조되었다. 졸-겔 법에 의해 합성된 세라믹 막을 통한 헬륨, 질소 투과 실험은 기체의 투과 특성을 파악하기 위하여 시행하였다. 질소에 대한 헬륨의 선택도는 $100{\sim}160$ 정도였으며 헬륨의 투과도는 $303{\sim}363K$의 온도 범위에서 $10^{-7}mol/m^2{\cdot}s{\cdot}Pa$ 정도였다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 추계학술발표대회
• /
• pp.43.2-43.2
• /
• 2011

Single-walled carbon nanotubes (SWCNT) are transparent in the visible and show conductivity comparable to copper, and are environmentally stable. SWCNT films have high flexibility, conductivity and transparency approaching that indium tin oxide (ITO), and can be prepared inexpensively without vacuum equipment. Transparent conducting Films (TCF) of SWCNTs has the potential to replace conventional transparent conducting oxides (TCO, e.g. ITO) in a wide variety of optoelectronic devices, energy conversion and photovoltaic industry. However, the sheet resistance of SWCNT films is still higher than ITO films. A decreased in the resistivity of SWCNT-TCFs would be beneficial for such an application. We fabricated SWCNT sheet with $KAuBr_4$ on PET substrate. Arc-discharge SWCNTs were dispersed in deionized water by adding sodum dodecyl sulfate (SDS) as surfactant and sonicated, followed by the centrifugation. The dispersed SWCNT was spray-coated on PET substrate and dried on a hotplate at $100^{\circ}C$. When the spray process was terminated, the TCF was immersed into deionized water to remove the surfactant and then it was dried on hotplate. The TCF film was then treated with AuBr4-, rinsed with deionized water and dried. The surface morphology of TCF was characterized by field emission scanning electron microscopy. The sheet resistance and optical transmission properties of the TCF were measured with a four-point probe method and a UV-visible spectrometry, respectively. $HNO_3$ treated SWCNT films with Au nano-particles have the lowest 61 ${\Omega}$/< sheet resistance in the 80% transmittance. Sheet resistance was decreased due to the increase of the hole concentration at the washed SWCNT surface by p-type doping of $AuBr_4{^-}$.

• 한국재료학회지
• /
• 제20권11호
• /
• pp.559-569
• /
• 2010

The liquid-phase sintering method was used to prepare a glass lens forming core composed of SiC-$Al_2O_3-Y_2O_3$. Spark plasma sintering was used to obtain dense sintered bodies. The sintering characteristics of different SiC sources and compositions of additives were studied. Results revealed that, owing to its initial larger surface area, $\alpha$-SiC offers sinterability that is superior to that of $\beta$-SiC. A maximum density of $3.32\;g/cm^3$ (theoretical density [TD] of 99.7%) was obtained in $\alpha$-SiC-10 wt% ($6Al_2O_3-4Y_2O_3$) sintered at $1850^{\circ}C$ without high-energy ball milling. The maximum hardness and compression stress of the sintered body reached 2870 Hv and 1110 MPa, respectively. The optimum ultra-precision machining parameters were a grinding speed of 1243 m/min, work spindle rotation rate of 100 rpm, feed rate of 0.5 mm/min, and depth of cut of $0.2\;{\mu}m$. The surface roughnesses of the thus prepared final products were Ra = 4.3 nm and Rt = 55.3 nm for the aspheric lens forming core and Ra = 4.4 nm and Rt = 41.9 for the spherical lens forming core. These values were found to be sufficiently low, and the cores showed good compatibility between SiC and the diamond-like carbon (DLC) coating material. Thus, these glass lens forming cores have great potential for application in the lens industry.

• 한국전기전자재료학회논문지
• /
• 제27권4호
• /
• pp.226-231
• /
• 2014

Thin thermistor films of solutions with nickel and manganese oxides were prepared by metal-organic decomposition (MOD). The structural properties of the thin films were investigated as a function of annealing temperature. Field emission scanning electron microscope (FE-SEM) results indicated that the thin films had a thin thickness, smooth and dense surface. The crystallization temperature of $414.9^{\circ}C$ was confirmed from thermogavimetric-differential thermal analysis (TG-DTA) curve. A single phase of cubic spinel structure was obtained for the thin film annealed from $700^{\circ}C$ to $800^{\circ}C$, which was confirmed from the X-ray diffraction (XRD). From the selected area electron diffraction (SAED) in high resolution transmission electron microscope (HRTEM), the nano grains (2~3 nm) of spinel phase with (311) and (222) planes were detected for the thin film annealed at $500^{\circ}C$, which could be applicable to read-out integrated circuit (ROIC) substrate of the uncooled microbolometer with low processing temperature.