• Particle and aerosol research
• /
• v.13 no.3
• /
• pp.133-139
• /
• 2017

In this paper, we proposed an emulsification method without using an emulsifier and investigated the effects of particle size distribution in fluids on dispersion stability. Surfactant-free oil in water emulsion was prepared with 1 % (w/w) of olive oil by using high speed agitation, high pressure and ultrasonic dispersion methods. The particle size, microscopic observation, and dispersion stability of each sample were evaluated and dispersion stability according to various dispersion methods was compared. As a result, the emulsion dispersed by the ultrasonic dispersion method showed the smallest particle size and uniform distribution of $0.07{\sim} 0.3{\mu}m$ and was the most stable in a 7 days stability evaluation. In the above experiment, four olive oil emulsions having different particle sizes were prepared using ultrasonic dispersion technology that was capable of producing stable emulsions. The dispersion stability of each samples with oil droplet sizes of (A) 0.1 to $0.5{\mu}m$, (B) 0.3 to $4{\mu}m$, (C) 1 to $10.5{\mu}m$ and (D) 2 to $120{\mu}m$, was observed for 7 days, and the relationship between the stability and performance was studied. Emulsion (A) with particle size less than $0.5{\mu}m$ displayed the dispersion stability showing below 5 % change in a 7 days stability evaluation. In the case of (B), (C), and (D) that had larger particle than $0.5{\mu}m$, the changes of dispersion stability were 10 %, 13 % and 35 % respectively. From these results, it was proved that dispersion stability of emulsion with uniform particle size of $0.5{\mu}m$ or less was confirmed to be very stable.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.519-520
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.195-196
• /
• 2006

• Membrane Journal
• /
• v.31 no.6
• /
• pp.426-433
• /
• 2021

In this study, a novel material polyketone (PK) was chosen and PK micro/nano fiber membranes were fabricated via electrospinning method under various conditions. After that, the potential application in oil-water separation was thoroughly investigated. The surface of microfiber membrane formed under high humidity especially became much rougher than that formed under low humidity. When salt was added to the spinning solution, the diameter of fibers was reduced up to 90% and the nanofiber membranes could be formed. The oil/water emulsions were prepared and separated under gravity condition using the manufactured rPK-LNC and PK-H membranes. The separation characteristics was evaluated by measuring total organic carbon (TOC) and turbidity. Meanwhile, the changes in the physical properties of fiber membranes under various conditions and with or without salt, as well as the changes in oil water separation characteristics were also studied.

• Applied Chemistry for Engineering
• /
• v.19 no.6
• /
• pp.640-644
• /
• 2008

Lubricating oil on aluminium surfaces was cleaned by a low temperature plasma process. Oxygen plasma mixed with argon was used, and process parameters were the mixing ratio of argon in oxygen, discharge power, and negative DC potential. The aluminium surfaces were analyzed with FTIR and EDX after the cleaning. It was found that almost all of the oil was eliminated in 20 min. if the oil was pure. Elimination efficiency was highly dependent on operational conditions of the process. The highest efficiency was obtained when treated at 300 W with oxygen plasma mixed with 30% argon applying negative potential more than -500 V on the aluminium surfaces. However, efficiency higher that 60% cannot be obtained at any condition if the oil contained inorganic materials.

• Journal of Power System Engineering
• /
• v.14 no.4
• /
• pp.50-55
• /
• 2010

In order to investigate tribological effects of nano copper particles impregnated(CuN) on surface polytetrafluoroethylene(PTFE) on sealing wear and an experimental study was carried out to determine the wear behavior of copper nano-particles impregnation two kind thickness in super critical $CO_2$ liquid. Experimental results showed that the friction coefficients of CuN PTFE at the low sliding speed(0.44m/s) and the oil temperature ($60^{\circ}C$) were higher than that of virgin PTFE. And a thin nano copper particles impreganated thickness was formed on the surface in the PTFE and the specimen with this treatment has much better friction properties than the original one. Fortunately, at the high load(80 N) and the oil temperature, the friction coefficient of CuN PTFE was lower than that of virgin PTFE. This evidenced the load carrying capacity of CuN PTFE was much better than that of virgin PTFE under the high load condition(80 N) specially. Therefore, it can be concluded that the friction coefficient variation of CuN PTFE is very small but its wear rate decreases greatly with increase in sliding speed.

• Journal of Digital Convergence
• /
• v.13 no.4
• /
• pp.369-375
• /
• 2015

In this study, the formation potential and the stability of nano-emulsions were evaluated according to the structure of various cosmetic oils in Tween 80/Span 80 system using PIC method at 80 oC LP 70, Isopar H and Pripure 3759 of hydrocarbons were both form a stable nano-emulsion, particle size distribution of about 40 nm. A linear structure of silicone oil formed an unstable emulsion, but cyclic or short chain oil formed was a stable nano-emulsion. In ester oils, the particle size of emulsions increases with increasing molecular weight of oils and a stable nano-emulsion could not be obtained in the molecular weight of about 450. The particle size of the nano-emulsion against required HLB value for calculating in consideration of the lipophilic and hydrophilic oil was smaller in the HLB of 8-10.

• Journal of Industrial Technology
• /
• v.43 no.1
• /
• pp.1-6
• /
• 2023

TiO₂ is a versatile metal oxide material that is frequently used as a photo-catalyst for organic pollutant oxidation and a functional material for ultraviolet-ray protection. To improve its chemical/physical properties and widen the range of industrial application, it is demanded to control the crystalline feature and morphology precisely by applying advanced nano-synthesis methods. In this study, we prepared TiO₂ nanoparticles using the water-in-oil (W/O) microemulsion method and compared them with the particles synthesized by the conventional precipitation method. Also, we tried to find the optimum conditions for obtaining nano-sized, anatase-rich TiO₂ particles by the W/O microemulsion method. We analyzed the crystalline feature and particle size of the prepared samples using X-ray diffraction (XRD) and Transmission electron microscopy (TEM). In summary, we found the W/O microemulsion is more effective than precipitation in obtaining nano-sized TiO₂. The best result was derived when the microemulsion was formed using AOT surfactant, hydrolysis was performed under basic condition and the sample was calcined at 200℃.

• Elastomers and Composites
• /
• v.44 no.1
• /
• pp.69-75
• /
• 2009

Asphalt sealants for the crack repair of asphalt concrete road were prepared using waste lubricant oil in this work. The waste lubricant oil was compounded with asphalt(AP-5), SBS triblock copolymer, a tackifying agent(petroleum resin), and antioxidants. Cone penetration, softening point, ductility, elongation by tensile adhesion, and resilience of asphalt sealant compounds were measured. Cone penetration of asphalt sealant compounds increased with the increase of waste lubricant oil content while their softening point, ductility, and resilience decreased. By the addition of talc as an extender, softening point and resilience of asphalt sealants increased, but cone penetration, ductility, and elongation by tensile adhesion of those decreased with the proportion of talc content. The most economic asphalt sealant which could pass an ASTM specification could be manufactured by the big decrement of petroleum resin content.

• Current Optics and Photonics
• /
• v.8 no.2
• /
• pp.170-182
• /
• 2024

The dimensional accuracy and consistency of a dual oil circuit centrifugal fuel nozzle are important for fuel distribution and combustion efficiency in an engine combustion chamber. A point cloud measurement method was proposed to solve the geometric accuracy detection problem for the fuel nozzle. An improved variance focus measure operator was used to extract the depth point cloud. Compared with other traditional sharpness evaluation functions, the improved operator can generate the best evaluation curve, and has the least noise and the shortest calculation time. The experimental results of point cloud slicing measurement show that the best window size is 24 × 24 pixels. In the height measurement experiment of the standard sample block, the relative error is 2.32%, and in the fuel nozzle cone angle measurement experiment, the relative error is 2.46%, which can meet the high precision requirements of a dual oil circuit centrifugal fuel nozzle.