• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1579-1582
• /
• 2005

철도 운전사고의 대부분을 차지하는 철도건널목에 대한 기존의 사고예측식은 국외의 경우 Peabody Dimmick Formula, New Hampshire Index, National Cooperative Highway Research Program(NCHRP) report 50, U.S. Department of Transportation(DOT) 사고예측식 등을 이용하고 있었으며, 국내의 경우, U.S. DOT 사고예측식의 입력변수를 다변량 분석법을 이용하여 국내에 맞게 조정한 사고예측식을 이용하고 있다. 그러나 위에서 제시한 철도건널목 사고예측식은 철도건널목에서 발생하는 사고를 단순히 철도통행량, 도로통행량, 선로수, 도로수 등의 요인에 국한하여 분석한 것이고, 사고예측식 자체가 철도건널목에만 국한된다는 맹점을 안고 있어서 철도건널목장치라든지 철도건널목을 이용하는 사람들의 성향 등, 여러 인자를 고려한 철도건널목에서의 안전성분석 및 대책을 제시할 필요가 있다. 본 논문에서는 철도건널목장치를 포함하여 다른 시스템에도 범용적으로 적용할 수 있고, 제한된 변수에만 국한하지 않아 여러 사항을 고려할 수 있는 안전성분석 절차를 제시하였는데 이 안전성 분석 절차를 철도건널목에 적용함으로써 시스템의 위험요인을 분석하고, 이에 대한 원인 및 결과, 손실을 도출한 후 대책을 제시할 수 있었다.

• Journal of Korean Society of Transportation
• /
• v.13 no.1
• /
• pp.125-152
• /
• 1995

The purposes of this study are twofold ; (1) to investigate the accuracy of estimation power of the individual models. such as those of Highway Capacity Nanual (HCM), Korea Highway Capacity Manual (KHCM), and NationalCooperative Highway Research Program(NCHRP) Report339 ; and (2) to develop an adjusted delay model which can be applied to the signal control system in urban areas. The study is mainly focused on four subjects related to the research purposes, which are as follows ; (1) characteristecs of exsisting delay models ; (2) inherent problems in exsisting delay models : (3) validation of the proposed model by the comparison of observed delay with estimated delay :and (4) a method which can be applied to develop an appropriate delay model for actrual signal control systems by the adjusted fact of the proposed model.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.4
• /
• pp.381-393
• /
• 2001

The current traffic situation in Korea can be described as rapid change in traffic volume and diversity in vehicle size from compact cars to large trucks. W-beam barrier most widely used in Korea was found not to satisfy the stiffness requirement for the Koran impact condition of 14 ton-60Km/h-15deg. and it was too stiff for small vehicles impacting with more realistic speed to satisfy the safety of vehicle occupants. To develop a guardrail system satisfying the two contradicting goals, a thrie-beam guardrail system, which had the beam thickness of 3.2mm and rubber cushions, was conceived. Even though the height of the thrie-beam(450mm) is increased by 100mm as compared to that of W-beam (350mm), there was only 2% increase in the weight of the thrie-beam. The new thrie-beam barrier system could contain more wide range of vehicle bumper heights, and showed better performance in the viewpoint of stiffness and energy absorbing capability than the W-beam system. The impact performance was evaluated from a crash test. The developed thrie-beam guardrail system satisfied all applicable criteria for NCHRP 350 test designation 3-10.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.183-183
• /
• 2011

전 국토의 65%가 산악지형으로 이루어져 있는 우리나라는 도로개설 및 산업기지 건설, 대규모 주택단지 개발 등으로 자연사면을 변형시키는 규모나 빈도가 증가하고 있고, 최근에는 기상이변에 의한 집중호우가 빈번히 발생하여 절토사면에서 낙석이 발생할 위험이 점점 높아지고 있는 실정이다. 낙석방지를 위한 대책공법으로는 낙석방지 망, 낙석방지 울타리 등이 있으며 이중에서 낙석방지 울타리는 국내의 국도 낙석방지 대책공법 중 70% 이상을 차지하고 있다. 그러나 국내 설계지침에는 낙석방지 울타리에 대한 다양한 성능등급과 성능평가를 위한 표준화된 시험방법이 제시되어 있지 않아 현장여건을 고려하여 적절한 낙석방지 울타리를 선정하고 낙석방지 울타리들의 성능을 비교검토하기에 어려움이 있다. 유럽의 경우 유럽연합 출범이후 낙석방지 시설에 대한 통합기준의 필요성이 대두되어 유럽 여러 나라의 성능평가 방법과 스위스의 설계지침을 고려하여 2008년에 유럽 통합 지침인 ETAG 27을 제정하였다. ETAG 27에는 낙석방지 울타리의 성능등급이 100kJ~4,500kJ이상 9등급으로 분류되어 있고 성능등급 별로 Service Energy Level과 Maximum Energy Level에 대하여 실물시험을 통한 성능평가 시험과 구성요소에 대한 검증시험을 수행하도록 되어있다. 실물시험은 낙석에너지의 산정과 낙석질량의 타격위치를 정확하게 결정할 수 있는 방법을 이용하여 수행토록 규정되어 있다. 미국의 경우에는 주별로 상이한 설계기준으로 인하여 발생하는 문제를 해소하기 위하여 2003년에 스위스의 설계지침을 준용하여 통합기준인 NCHRP Report 20-07을 결정하였다. NCHRP Report 20-07에는 낙석방지 울타리의 성능등급이 100kJ~5,000kJ까지 9등급으로 분류되어 있고 성능등급 별 낙석질량이 규정되어 있으며 등급별 낙석에너지의 50%와 100%에 대하여 실물시험을 통한 성능평가 시험을 수행하도록 되어 있다. 실물시험은 낙석에너지의 산정과 낙석질량의 타격위치를 정확하게 결정할 수 있는 방법을 이용하여 수행토록 규정되어 있다. 낙석방지 울타리에 대한 국내 설계지침과 유럽과 미국의 설계지침을 비교분석하고 국내에서 수행된 실물실험을 통한 성능평가 연구결과를 검토하였다. 또한 구성요소의 역학적 특성변화가 전체 시스템의 성능에 미치는 영향을 조사하기 위해서 국내 설계 지침에 제시된 낙석방지 울타리에 대하여 컴퓨터 시뮬레이션을 이용한 성능평가를 수행하였다. 이러한 연구결과에 근거하여 국내 설계지침은 현장여건에 따라 적절한 낙석방지 울타리를 선정할 수 있도록 다양한 성능등급을 규정하고, 낙석방지 울타리의 성능을 합리적으로 비교검토 할 수 있게 하는 표준화 성능평가 시험방법과 평가기준을 정립하며, 구성요소의 품질에 대한 신뢰성을 확인하는 구성요소의 검증시험을 포함하는 방향으로 개선될 필요가 있는 것으로 조사되었다.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.10
• /
• pp.5-16
• /
• 2015

Considering the conversion of the Korea Construction Standards to Limit State Design (LSD), we analyzed the resistance bias factor for pullout resistance, as a part of the development of the Load and Resistance Factor Design (LRFD) for soil nailing; very few studies have been conducted on soil nailing. In order to reflect the local characteristics of soil nailing, such as the design and construction level, we collected statistics on pullout tests conducted on slopes and excavation construction sites around the country. In this study a database was built based on the geotechnical properties, soil nailing specifications, and pullout test results. The resistance bias factors are calculated to determine the resistance factor of the pullout resistance for gravity and pressurized grouting method, which are the most commonly used methods in Korea; moreover, we have relatively sufficient data on these methods. We found the resistance bias factors to be 1.144 and 1.325, which are relatively conservative values for predicting the actual ultimate pullout resistance. It showed that our designs are safer than those found in a research case in the United States (NCHRP Report); however, there was an uncertainty, $COV_R$, of 0.27-0.43 in the pullout resistance, which is relatively high. In addition, the pressurized grouting method has a greater margin of safety than the gravity grouting method, and the actual ultimate pullout resistance determined using the pressurized grouting method has low uncertainty.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.36 no.2
• /
• pp.113-120
• /
• 2023

This paper introduces a simulation method for the collision between roadblocks and vehicles using LS-DYNA. The need to evaluate the performance of anti-ram barriers to prepare for vehicle impact has increased since vehicle impact threats have been included as a design criterion for nuclear power plants. Anti-ram barriers are typically certified for their performance through collision experiments. However, because Koreas has no performance testing facilities for anti-ram barriers, their performance can only be verified through simulations. LS-DYNA is a specialized program for collision simulation. Various organizations, including NCAC, distributes numerical models that have been validated for their accuracy with collision tests. In this study, we constructed a finite element model of the most critical vehicle barrier module and simulated collision between roadblocks and vehicles. The calculated results were verified by applying the validation criteria for vehicle safety facility collision simulations of NCHRP 179.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.877-883
• /
• 2009

Shaking table tests are performed to evaluate the dynamic group pile effect in fine sand. Single pile tests and $2{\times}4$ group pile tests are performed on 3D pile spacing. Dynamic p-y backbone curves are obtained to evaluate dynamic group pile effect by using dynamic p-y curve of single pile. And dynamic group pile p-multiplier is estimated by dynamic p-y backbone curve. Dynamic p-multiplier can be calculated by using subground reaction ratio of dynamic p-y backbone curve which is the same displacement of p-y curve peak point As the result, dynamic group pile effects are evaluated in terms of a shaking frequency, a shaking acceleration, and a relative density. Dynamic group pile p-multiplier is the largest at lead pile, and the value decrease at middle pile and trail pile. p multiplier increases as increasing input acceleration and decreasing relative density. This results coincide with NCHRP's research which suggest p multiplier increases as increasing pile cap displacement.

• International Journal of Highway Engineering
• /
• v.19 no.2
• /
• pp.97-102
• /
• 2017

PURPOSES : Emulsified asphalt is critical for road construction. The objective of applying asphalt emulsion as an adhesive is to prevent the phenomenon of debonding between the upper and lower layers. The quantity and veriety of bituminous material can be varied according to the type of pavement and site conditions. The objective of this study is to reveal the optimum application rates of the emulsified asphalt materials by types of tack-coats using Interface Shear Strength(ISS). METHODS : In the research, emulsified asphalt was paved on the surface of the divided mixture. The specimens of paving asphalt emulsion were utilized to evaluate the bond strength of tack-coat materials. In the evaluation process, NCHRP Report 712 was utilized to investigate the Interface Shear Strength, which reflects the bond capacity of asphalt emulsion. Then, the optimum residual application rates by tack-coat types were determined using regression analysis. RESULTS :As a consequence of squared R values investigated from 0.7 to 1 as part of the regression analysis, the tendency of predicted ISS values was compared with the results. The optimum residual application rates of AP-3, RS(C)-4, QRS-4, and BD-Coat were determined to be $0.78{\ell}/m^2$, $0.51{\ell}/m^2$, $0.53{\ell}/m^2$, and $0.73{\ell}/m^2$, respectively, utilizing 4th regression analysis. CONCLUSIONS :Based on the result of this study, it was not feasible to conclude whether higher residual application of tack-coat material leads to improved bond capacity. Rather, the shearing strength varies depending on the type of pavement.

• Journal of the Korean Society of Safety
• /
• v.27 no.6
• /
• pp.185-191
• /
• 2012

Rear collisions to expressway work trucks result many casualties these days. But, currently, no special measure are being taken except deploying sign trucks behind the working trucks. In the U.S and Europe, trucks with TMA(Truck Mounted Attenuator) are being deployed behind the working truck, which is regarded as the standard method for work area safety, thereby reducing the fatality rates and property damage tremendously. Also, standard for the performance of TMA are established and TMA can be used in the field only when it satisfies the standard. In Korea, neither the standard for nor any guide to the TMA exists. In the situation some manufacturer developed TMA without proper performance evaluation and marketed limited number of TMAs in the field. In the study, NCHRP350, which is the performance standard of expressway safety features of U.S. and materials related to the TMA standard in Europe have been reviewed to establish the Korean performance criteria. Based on the review, and incorporating existing Korean standard for crash cushions, domestic standard for TMA has been proposed and applied in developing Korean TMA and crash tested it to verify the performance. The original design developed was crash tested and modified. The newly proposed design was studied using impact simulation program several times. Modifications were made after each simulation and prototype was built and crash tested as per the newly established TMA performance criteria.

• International Journal of Highway Engineering
• /
• v.18 no.6
• /
• pp.137-143
• /
• 2016

OBJECTIVES : Bituminous materials, such as tack coat, are utilized between pavement layers for improving the bond strength in pavement construction sites. The standards regarding the application of bituminous material are not clearly presented in the Korean construction guideline without RS(C)-4. Hence, the objective of this study is to determine the optimum content of bituminous materials by analyzing interlayer shear strength (ISS) from the direct shear tester, which was developed in this research. The shear strength of tack coat was defined with the sort of bituminous materials. METHODS : The mixtures for the shear test were made using marshall mix design. The specimens were vertically and horizontally separated for the direct shear test. The separated specimens were bonded using bituminous material. The objectives of the experiment are to determine the performance of bond and shear properties resulting from slippage, rutting, shovel, and corrugation of asphalt pavements. A machine based on the Louisiana interlayer shear strength tester (LISST) of NCHRP Report-712 was developed to determine the ISS. The applied types of tack coat were RS(C)-4, AP-3, QRS-4, and BD-coat with contents of $0.3{\ell}/m^2$, $0.45{\ell}/m^2$, $0.6{\ell}/m^2$, and $0.8{\ell}/m^2$, respectively. RESULTS : Table 2 gives the results of the direct shear test using the developed shear machine. The BD-coat type indicated the highest average ISS value compared to the others. Between the surface and binder course, optimum tack coat application rates for AP-3, RS(C)-4, QRS-4, and BD-Coat were $0.6{\ell}/m^2$, $0.3{\ell}/m^2$, $0.6{\ell}/m^2$, and $0.45{\ell}/m^2$, respectively. These optimum contents were determined using the ISS value. CONCLUSIONS : The ISS values of AP-3, RS(C)-4, and QRS-4 showed similar tendencies when ISS increased in the range $0.3{\sim}0.6{\ell}/m^2$, while ISS decreased when the applied rate exceeded $0.6{\ell}/m^2$. Similarly, the highest ISS value of the BD-coat was observed when the applied rate was $0.45{\ell}/m^2$. However, shear strength was similar to the maximum value of ISS when the tack-coat application rate of BD-Coat exceeded $0.45{\ell}/m^2$.