• Journal of KIISE:Information Networking
• /
• v.30 no.1
• /
• pp.134-142
• /
• 2003

We present an ATM switch architectures based on the multistage interconnection network(MIN) for the efficient multicast traffic control. Many of these applications require multicast connections as well as point-to-point connections. Muiticast connection in which the same message is delivered from a source to arbitrary number of destinations is fundamental in the areas such as teleconferencing, VOD(video on demand), distributed data processing, etc. In designing the multicast ATM switches to support those services, we should consider the fairness(impartiality) and priority control, in addition to the overflow problem, cell processing with large number of copies, and the blocking problem. In particular, the fairness problem which is to distribute the incoming cells to input ports smoothly is occurred when a cell with the large copy number enters upper input port. In this case, the upper input port sends before the lower input port because of the calculating method of running sum, and therefore cell arrived into lower input port Is delayed to next cycle to be sent and transmission delay time becomes longer. In this paper, we propose the cell splitting and group splitting algorithm, and also the fairness scheme on the basis of the nonblocking characteristics for issuing appropriate copy number depending on the number of Input cell in demand. We evaluate the performance of the proposed schemes in terms of the throughput, cell loss rate and cell delay.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.2
• /
• pp.1013-1019
• /
• 2011

In this paper, simulation works for a multi-stage cascade refrigeration cycle using propane, ethylene and methane as refrigerants have been performed for the liquefaction of natural gas using Peng-Robinson equation of state built-in PRO/II with PROVISION release 8.3. The natural gas feed compositions were supplied from Korea Gas Corporation and the flow rate was assumed to be 5.0 million tons per annual. Supply temperature for propane refrigerant was fixed as $-40^{\circ}C$, that for ethylene refrigerant as $-95^{\circ}C$, and that for methane refrigerant as $-155^{\circ}C$. For the multi-stage refrigeration cycle, three-stage refrigeration was assumed for propane refrigeration cycle, two-stage refrigeration for ethylene refrigeration cycle and three-stage refrigeration for methane refrigeration cycle. Natural gas was finally cooled and liquefied to $-162^{\circ}C$ by Joule-Thomson expansion. Conclusively, 91.71% by mole of the natural gas liquefaction ratio was obtained through a cascade refrigeration cycle and Joule-Thomson expansion and 0.433 kW of compression power was consumed for the liquefaction of 1.0 kg/hr of natural gas.

• Journal of Preventive Medicine and Public Health
• /
• v.34 no.4
• /
• pp.331-336
• /
• 2001

Objectives : To assess the prevalence of knee osteoarthritis through proper diagnosis in a rural community and to elucidate the relevant factors of this health problem in order to develop educational methods for the prevention of female knee osteoarthritis as well to provide basic data for prospective research. Methods : Over a period of three months starting from August, 2000, 432 women over the age of 40 and living in a rural area were selected by a multistage cluster sampling method in order to investigate the prevalence of knee osteoarthritis and the related factors. The study utilized interviews and radiological examination. The criteria of knee osteoarthritis used was the American College of Rheumatology classification criteria for osteoarthritis of the knee(1995). Results : The adjusted prevalence of knee osteoarthritis among the subjects was 55.0%, and multiple logistic regression analysis showed that the odds ratio(OR) of knee osteoarthritis among subjects 50-59 years of age and subjects older than 60 years of age as compared to subjects 40-49 years of age were 2.43(95% CI: 1.30-4.70) and 4.40(95% CI: 2.47-7.83), respectively. The OR of knee osteoarthritis among factory workers or farmers as compared to others was 1.79(95% CI: 1.03-3.12). The OR of knee osteoarthritis among subjects who had a family history and subjects who had knee injury or surgical history against those subjects had neither were 2.56(95% CI: 1.42-4.03) and 4.70(95% CI:1.45-15.19), respectively. The OR of knee osteoarthritis among smokers against non smokers was 0.47(95% CI: 0.22-0.97). Conclusions : Related factors of knee osteoarthritis included age, occupation, family history, smoking, knee injury and history of surgery In order to prevent knee osteoarthritis in high risked rural woman, education concerning self-care methods and safety guideline must be provided at the work place by the public and private health sectors. Additionally, these women should be continually encouraged to exercise, including jogging and swimming regularly.

• Resources Recycling
• /
• v.6 no.3
• /
• pp.3-8
• /
• 1997

The EA.F. sleelmaking slag (slag that follow) of a cnmvany 1 Co.. containzd a simple substance of a metal, wustlte (FeO), magnetite (Fe,O,), gehlenite (CaAl,SiO,), monlicellite (CaMgSiO,), dc. To recovere a metal (Fe grade . t95%) in the slag, it is desirable that the particles of a metal are isolated from thc slag and madc for a liberated subslance. Then, the liberaled melal is easlly recoveled by a magnetic separation. If thc rcclarnalcd slag, the sizc of which ranges under 40 nun, have a mulli-stage crushing, the most of a metal in thc slag is simply isolaled as a liberated subslance. If the mad, lhat is a liberated subslance and a sphere, is recovered by a magnetic field intensity. the minimum intensity, at which a metal is attracted, is approximately IOOG and did no1 dcpcnd on the particle size of a metad in the same particles. TIe recovered material. that contdined a iron (Fe) over 95% is a metal which is crushed slag by l00G in the multi-stage. If the magnetic field intcns~ty increase, the recovery mcrcasc, but the concentration grade decrease Bewusc thc concentration eams more and more impurities, iron oxide and the coml~ound of alkali earth element. 'll~ercforc If the rccla~nated slag have the multi-stage crushing, the metal is almostly recovered in the crushed slag by lO0G on each particles. If the slag, used as a rcclamatian lhat is a amount of 350,000 tan from I Co., was undcr the multistage crushing and then separaled by 100gauss, it is possible to recova a metal approximately 2.500 Ion, lhat is 0.73% of n ~eclamated slag. in 304.7 mm particles and to recover 4.200 tan in 0.3-1.7 mm particles , that is 1.2% nf a rcclamated slag, in a year. Therefore, ihe told recoverable meld is 6,700 ton, that is 19% of a reclmated slag, in a year, too.

• Korean Chemical Engineering Research
• /
• v.56 no.6
• /
• pp.864-870
• /
• 2018

The effect of lower bed height on the collapse velocity was investigated for a two-stage bubbling fluidizedbed (0.1 m in diameter, 1.2 m high) connected with a standpipe (0.025 m in diameter) for solid transport. Air was used as fluidizing gas and mixture of coarse (< $1000{\mu}m$ in diameter and $3625kg/m^3$ in apparent density) and fine (< $147{\mu}m$ in diameter and $4079kg/m^3$ in apparent density) particles as solid particles. Mixing ratio of fine particles, height of the lower bed and the distributor of the upper bed were considered as experimental variables. The collapse velocity increased with static height of the lower bed. However, the effect decreased as the mixing ratio of fine particles increased. The effect seemed to be attributed to the increase in height of the dense layer of coarse particles that prevented the gas from flowing into the standpipe, not in pressure drop for the standpipe, as the bed height increased. The collapse velocity decreased a little as the pressure drop of the distributor of the upper bed increased. An improved correlation was proposed for predicting the collapse velocity.

• Journal of the Korean Society of Safety
• /
• v.37 no.4
• /
• pp.20-27
• /
• 2022

This article aims to develop an algorithm that detects fire pump defects by analyzing the current signals of an induction motor, which are triggered by changes in the flow rate and pressure of multistage volute pumps that are used for fire services. The operational status of the pumps was categorized into three: first, normal operation; second, a defect that is caused by a change in the current value; and third, a defect occasioned by a change in current, pressure, and flow rate. When a fire pump was in normal operation, the motor's operating current was measured between 5.06 A and 6.9 A, the flow rate was estimated at 0-0.27 m³/min, and the pressure ranged from 0 to 0.47 MPa. In the event that a defect was caused by an abnormal current value in the motor, it was attributed to the pump's adherence. Furthermore, if there was no source of water, the defect was considered to have been induced by phase-loss operation, no-load operation, or run-stop operation, with the current value of each scenario being measured at > 52.8 A, < 4.13 A, > 45.15 A, and < 3.8 A, respectively, placing its overall range between 0 and 50 A. The sources of defects were detected based on an analysis of the flow rate, pressure, and current, which represent the following causes: air inflow into the casing, inadequate suction of water, and reverse-phase operation, respectively. Each cause entailed the following values: when air seeped into the casing, the pressure was measured at 0.24 MPa irrespective of changes in the flow rate; when there was inadequate suction of water, the pressure was recorded between 0 and 0.05 MPa despite changes in the flow rate; and when the power line's reverse-phase loss was the cause of the defect, the pressure was measured at 0.33 MPa for a flow rate of 0 L/min, and a higher flow rate decreased the pressure to nearly 0 MPa. The results of this study will enable engineers to develop a pump defect detection algorithm that is based on an analysis of current, and this algorithm will facilitate the execution of a program that will control a fire pump defect detection system.

• Korean small business review
• /
• v.41 no.3
• /
• pp.49-75
• /
• 2019

Market instability offers opportunities as well as the need for careful innovation strategies and learning for a company's survival. Companies that find new opportunities decide to carry out innovation and decide on the size of their investments by considering their position in the market they are aiming for and the intensity of competition. This study was conducted to check whether obstacles to innovation face by SMEs in the manufacturing sector vary depending on the stage of corporate growth and to identify the impact of the government support system on the decision-making process on the performance of innovation. According to the analysis, there were differences in obstacles to innovation depending on the stage of corporate growth. It was found that more innovative SMEs are, more obstacles they face, and to overcome such obstacles, they try to access government support systems more. In addition, the use of a government support system eliminated obstacles to innovation, and the positive and significant effects of investing in innovation were identified. This study is meaningful in that it explicitly approached these hypotheses by applying a multistage model to the process of innovation carried out by SMEs in the manufacturing sector.

• Journal of radiological science and technology
• /
• v.36 no.3
• /
• pp.227-235
• /
• 2013

In adaptive radiotherapy(ART), generated composite dose of surrounding normal tissue on overall treatment course which is using deformable image registration from multistage images. Also, compared with doses summed by each treatment plan and clinical significance is considered. From the first of May, 2011 to the last of July, 2012. Patients who were given treatment and had the head and neck cancer with 3-dimension conformal radiotherapy or intensity modulated radiotherapy, those who were carried out adaptive radiotherapy cause of tumor shrinkage and weight loss. Generated composite dose of surrounding normal tissue using deformable image registration was been possible, statistically significant difference was showed to mandible($48.95{\pm}3.89$ vs $49.10{\pm}3.55$ Gy), oral cavity($36.93{\pm}4.03$ vs $38.97{\pm}5.08$ Gy), parotid gland($35.71{\pm}6.22$ vs $36.12{\pm}6.70$ Gy) and temporomandibular joint($18.41{\pm}9.60$ vs $20.13{\pm}10.42$ Gy) compared with doses summed by each treatment plan. The results of this study show significant difference between composite dose by deformable image registration and doses summed by each treatment plan, composite dose by deformable image registration may generate more exact evaluation to surrounding normal tissue in adaptive radiotherapy.

• Journal of Soil and Groundwater Environment
• /
• v.13 no.5
• /
• pp.81-87
• /
• 2008

In accompany with the transfer of US army bases, recent surveys reported serious contamination of soils by the release of petroleum from storage facilities and heavy metals accumulated in rifle-ranges. These problems have made an increased concerns of cleanup technology for contaminated soils. In this study, a full-scale soil washing process improved by multistage continuous desorption and agitational desorption techniques was examined for petroleum-contaminated soils obtained from three different remedial sites that contained 29.3, 16.6, and 7.8% of silt and clay, respectively. The initial concentrations of total petroleum hydrocarbon (TPH) were 5,183, 2,560, and 4,860 mg/kg for each soil. Pure water was applied to operate washing process, in which water used for washing process was recycled 100% for over 6 months. The results of full-scale washing tests showed that the TPH concentrations for soils (> 3.0 mm) were 50${\sim}$356 mg/kg (85.2${\sim}$98.2% removal rates), regardless of the contents of silt and clay from in A, B and C soil, when the soils were washed at 3.0 kg/$cm^2$ of injection pressure with the method of wet particle separation. Based on the initial TPH concentration, the TPH removal rates for each site were 85.2, 98.2 and 89.9%. For soils in the range of 3.0${\sim}$0.075 mm, the application of first-stage desorption technique as a physical method resulted 834, 1,110, and 1,460 mg/kg of TPH concentrations for each soil, also additional multi-stage continuous desorption reduced the TPH concentration to 330, 385, and 245 mg/kg that were equivalent to 92.4, 90.6, and 90.1% removal rates, respectively. The result of multi-stage continuous desorption for fine soil (0.075${\sim}$0.053 mm) were 791, 885, and 1,560 mg/kg, and additional agitation desorption showed 428, 440, and, 358 mg/kg of TPH concentrations. Compared with initial concentration, the removal rates were 92.0, 93.9 and 92.9%, respectively. These results implied we could apply strategic process of soil washing for varies types of contaminated soils to meet the regulatory limit of TPH.

• Journal of Sericultural and Entomological Science
• /
• v.52 no.1
• /
• pp.73-78
• /
• 2014

This study was carried out to establish the self-specification and shelf-life by standardization of manufacturing process for Tenebrio molitor larvae. First, standardization of manufacturing process for T. molitor was set up. Sterilization for larvae placed on a multistage shelf with intervals of about 10 cm was carried out at $115^{\circ}C$, $1kgf/cm^2$ for 10 min. After sterilization, T. molitor larvae were frozen at less than $-35^{\circ}C$ for more than 12 hrs. And then, they were dried under $-15^{\circ}C$, 0.5 torr vacuum for more than 30 hrs. Second, we decided self-specification for T. molitor larvae. Their moisture, acidity, peroxide, crude protein and crude fat level should be 5% or less, 3 mg/g or less, 30 meq/g or less, 45% or more, and 25% or more, respectively. Also, oleic acid, representative material, level was set up 11 ~ 16%. Third, we decided shelf-life by analysis of the physicochemical characteristic, sensory evaluation and microbial indicators. The final expiry date for lyophilized T. molitor larvae in PET bottle was calculated as 12 months from date of manufacture. We expect that optimal manufacturing process system, self-specification, and shelf-life proposed in this study can be used in industrial production of T. molitor as a novel food.