• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.10A
• /
• pp.1590-1597
• /
• 2000

This paper describes a CMOS data recovery circuit using oversampling technique. Digital oversampling is done using a delay locked loop circuit locked to multiple clock periods. The delay locked loop circuit generates the vernier delay resolution less than the gate delay of the delay chain. The transition and non-transition counting algorithm for 4x oversampling was implemented for data recovery and verified through FPGA. The chip has been fabricated with 0.6um CMOS technology and measured results are presented.

• Communications for Statistical Applications and Methods
• /
• v.15 no.1
• /
• pp.13-26
• /
• 2008

Inference on the present data will be more reliable when the data arising from previous similar studies are available. The data arising from previous studies are referred as historical data. The power prior is defined by the likelihood function based on the historical data to the power $a_0$, where $0\;{\le}\;a_0\;{\le}\;1$. The power prior is a useful informative prior for Bayesian inference such as model selection and model comparison. We utilize the historical data to perform multiple comparison in the one-way ANOVA model. We demonstrate our results with some simulated datasets under a simple order restriction between the treatments.

• Korea-Australia Rheology Journal
• /
• v.12 no.3_4
• /
• pp.181-186
• /
• 2000

Rheological Properties of polypropylenes having different molecular structures (linear polypropylene (PPL) and branched one (PPB)) were studied. Both the extensional flow and oscillatory shear flow properties were checked. Especially, the melt strength of polypropylenes having various shear history were investigated by using in-house-made Rheometer (called SMER). Compared to linear polypropylene, the branched polypropylene shows enhanced melt strength during extensional flow due to the retarded relaxation of molecules. When the slope of melt tension was plotted against take up speed of melt strand, the characteristic peak was observed in case of branched polypropylene, while the linear polypropylene shows only monotonously decreasing pattern. This entanglement was partially disrupted by physical forces such as shear during melt extrusion. However, the melt strength of PPB after multiple extrusion is still higher than PPL, implying the loss of elasticity during multiple extrusion is not so comprehensive. On dynamic experiments, PPB shows typical shear thinning behavior and the tangent delta of PPB is lower than PPL, reflecting high elasticity of PPB.

• ETRI Journal
• /
• v.19 no.1
• /
• pp.13-25
• /
• 1997

In this paper, we propose a new queuing model, MMDP/MMDP/1/K, for an asynchronous transfer mode(ATM) multiplexer with multiple quality of service(QoS) variable bit rate (VBR) traffic in broadband-integrated services digital network (B-ISDN). We use the Markov Modulated Deterministic Process(MMDP) to approximate the actual arrival process and another MMDP for service process Using queuing analysis, we derive a formula for the cell loss probability of the ATM multiplexer in terms of the limiting probabilities of a Markov chain. The cell loss probability can be used for connection admission control in ATM multiplexer and the calculation of equivalent bandwidth for arrival traffic, The major advantages of this approach are simplicity in analysis, accuracy of analysis by comparison of simulation, and numerical stability.

• Journal of information and communication convergence engineering
• /
• v.8 no.5
• /
• pp.513-518
• /
• 2010

This paper proposes a medium access control protocol for integrated voice and data services in slotted CDMA systems. The proposed protocol, which is named as RCSSMA (Reservation Code and Status Sensing Multiple Access), adopts a code reservation and status sensing schemes. RCSSMA protocol gives higher access priority to the voice traffic than data traffic for reducing the packet dropping probability. The voice terminal reserves an available spreading code to transmit voice packets during a talkspurt, whereas the data terminal transmits a packet over one of the available spreading codes that are not reserved by the voice terminals. In this protocol, the voice packets never contend with the data packets. Packet dropping probability and average data packet transmission delay are analyzed using a Markov chain model.

• Journal of information and communication convergence engineering
• /
• v.15 no.4
• /
• pp.227-231
• /
• 2017

Recently, as the number of safety accidents caused by reagents increases, researches on a system that can reduce safety accidents are underway. Existing systems managed reagent cabinet through various sensors. On the other hand, there are disadvantages in that countermeasures against simultaneous danger situations are insufficient at multi-reagents cabinet. In order to solve this problem, this paper proposes a system to manage the reagents cabinet through danger priority. Danger priorities are selected through domestic chemical accident cases and the Chemical Safety Management Act. If a danger situation occurs in the reagent cabinet, make sure it is from a single or multiple reagent cabinets. For multiple reagent cabinets, compare the reagent cabinet priorities and run the device sequentially from the reagent cabinet with the highest priority. Thus, by operating the device according to the danger priority, the chain reaction can be prevented in advance and the reagent cabinet can be safely managed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.1 no.2
• /
• pp.105-111
• /
• 1995

This paper proposes a segmentation algorithm using gray-level discontinuity and surface reflectance ratio of input images obtained under different illumination conditions. Each image is divided by a certain number of subregions based on the thresholds. The thresholds are determined using the histogram of fusion image which is obtained by ANDing the multiple input images. The subregions of images are projected on the eigenspace where their bases are the major eigenvectors of image matrix. Points in the eigenspace are classified into two clusters. Images associated with the bigger cluster are fused by revised ANDing to form a combined edge image. Missing edges are detected using surface reflectance ration and chain code. The proposed algorithm obtains more accurate edge information and allows to more efficiently recognize the environment under various illumination conditions.

• ETRI Journal
• /
• v.33 no.3
• /
• pp.374-381
• /
• 2011

A simple and effective compression method is proposed for multiple-scan testing. For a given test set, each test pattern is compressed from the view of slices. An encoding table exploiting seven types of frequently-occurring pattern is used. Compression is then achieved by mapping slice data into codewords. The decompression logic is small and easy to implement. It is also applicable to schemes adopting a single-scan chain. Experimental results show this method can achieve good compression effect.

• Proceedings of the KIEE Conference
• /
• 1998.11b
• /
• pp.669-671
• /
• 1998

Due to the serial nature of scan chains, the use of the boundary scan chain leads the high application costs. And with 3-state net, it is important to avoid enabling the two drivers in a net. In this paper, the new test method for 3-state nets in the multiple boundary scan chains is presented. This method configures the boundary scan cells as multiple scan chains and the test application time can be reduced. Also three efficient algorithms are proposed for testing the interconnects in a board without the collision of the test data in 3-state nets.

• Journal of the Korea Safety Management & Science
• /
• v.18 no.4
• /
• pp.185-193
• /
• 2016

Now, many studies of industrial field are focusing on the whole optimization of SCM. But, the reason for making simultaneity of the whole system of SCM difficult is reduced scale of studies on ordering area in SCM reducing the complexity. It's an important issue how to allocate orders in the environment of many suppliers under special situation. Through this thesis, this research intends to expect systematic and arranged supply of distribution area which can make a decision while allocating product orders and quantity and maintaining service standard suggested by minimizing total purchase costs.