• International journal of advanced smart convergence
• /
• v.7 no.3
• /
• pp.37-43
• /
• 2018

Lattice-reduction (LR) techniques have been developed for signal detection in spatial multiplexing multiple input multiple output (MIMO) systems to obtain the largest diversity gain. Thus, an LR-assisted zero-forcing (ZF) receiver can achieve the maximum diversity gain in spatial multiplexing MIMO systems. In this paper, a simplified analysis of the achievable diversity gain is presented by fitting the channel coefficients lattice-reduced by a complex Lenstra-Lenstra-$Lov{\acute{a}}z$ (LLL) algorithm into approximated Gaussian random variables. It will be shown that the maximum diversity gain corresponding to two times the number of receive antennas can be achieved by the LR-based ZF detector. In addition, the approximated bit error rate (BER) expression is also derived. Finally, the analytical BER performance is comparatively studied with the simulated results.

• Journal of Communications and Networks
• /
• v.18 no.3
• /
• pp.320-326
• /
• 2016

In existing literature on multiple-input multiple-output (MIMO) relaying communication systems, antenna selection is often implemented by maximizing the channel capacity or the output single-to-noise ratio (SNR). In this paper, we propose an energy-efficient low-complexity antenna selection scheme for MIMO relaying communication systems. The proposed algorithm is based on beamforming and maximizing the Frobenius norm to jointly optimize the transmit power, number of active antennas, and antenna subsets at the source, relaying and destination. We maximize the energy efficiency between the link of source to relay and the link of relay to destination to obtain the maximum energy efficiency of the system, subject to the SNR constraint. Compared to existing antenna selection methods forMIMO relaying communication systems, simulation results demonstrate that the proposed method can save more power in term of energy efficiency, while having lower computational complexity.

• Journal of Communications and Networks
• /
• v.9 no.2
• /
• pp.141-149
• /
• 2007

Multiple-input multiple-output (MIMO) transmit pre-coding/beamforming can significantly improve system spectral efficiency. However, several obstacles prevent precoding from wide deployment in early wireless networks: The significant feedback overhead, performance degradation due to feedback delay, and the large storage requirement at the mobile devices. In this paper, we propose a precoding method that addresses these issues. In this approach, only 3 or 6 bits feedback is needed to select a precoding matrix from a codebook. There are fifteen codebooks, each corresponding to a unique combination of antenna configuration (up to 4 antennas) and codebook size. Small codebooks are prestored and large codebooks are efficiently computed from the prestored codebook, modified Hochwald method and Householder reflection. Finally, the feedback delay is compensated by channel prediction. The scheme is validated by simulations and we have observed significant gains comparing to space-time coding and antenna selection. This solution was adopted as a part of the IEEE 802.16e specification in 2005.

• Journal of Communications and Networks
• /
• v.13 no.5
• /
• pp.463-471
• /
• 2011

Cooperative communications using relays in wireless networks have similar effects of multiple-input and multiple-output without the need of multiple antennas at each node. To implement cooperation into a system, efficient protocols are desired. In IEEE 802.11 families such as a/b/g, mobile stations can automatically adjust transmission rates according to channel conditions. However throughput performance degradation is observed by low-rate stations in multi-rate circumstances resulting in so-called performance anomaly. In this paper, we propose active relay-based cooperative medium access control (AR-CMAC) protocol, in which active relays desiring to transmit their own data for cooperation participate in relaying, and it is designed to increase throughput as a solution to performance anomaly. We have analyzed the performance of the simplified AR-CMAC using an embedded Markov chain model to demonstrate the gain of AR-CMAC and to verify it with our simulations. Simulations in an infrastructure network with an IEEE 802.11b/g access point show noticeable improvement than the legacy schemes.

• Journal of Advanced Information Technology and Convergence
• /
• v.8 no.2
• /
• pp.13-25
• /
• 2018

The paper analyzes the sum spectral efficiency (SE) for a heterogeneous cellular network (HetNet) which has the backhaul, provided with wireless full-duplex massive multiple-input multiple-out (MIMO) with hardware distortions. We derive approximate expressions to obtain the uplink/downlink sum SE of the backhaul. The analytic results have been shown to be exact when compared to Monte Carlo simulations. From the analysis, it is shown that the desired signal and the hardware distortion noise have the same order. The sum SE generally improves when the number of receive antennas increases but degrades when the hardware quality reduces. A sum SE performance ceiling is introduced by the hardware quality level.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.10
• /
• pp.61-67
• /
• 2004

The next generation cellular wireless communication systems require high data rate transmissions and large system capacities. In order to meet these requirements, multiple antennas can be used at the base and mobile stations, forming MIMO(Multiple Input Multiple Output) channels. This paper proposes a MIMO SDMA(Space Division Multiple Access) technique with dynamic slot allocation which allows the transmitter to efficiently transmit parallel data streams to each of multiple receivers. The proposed technique can increase system capacities significantly by transmitting a larger number of data streams than conventional MIMO techniques while minimizing the performance degradation due to the beamforming dimension reduction.

• Journal of electromagnetic engineering and science
• /
• v.18 no.2
• /
• pp.78-87
• /
• 2018

This paper describes specular reflectance measurements of dielectric plates in three waveguide frequency bands: D-band (110-170 GHz), G-band (140-220 GHz), and J-band (220-325 GHz). The transmit (Tx) part of the proposed specular reflectance measurement system is stationary, while the receive (Rx) part and the material under test (MUT) holder are concentric-rotating with a 2:1 speed ratio for specular reflectance measurements. In specular reflectance measurements, the first step measures the specular reflection coefficients of an MUT and a metal plate on the MUT holder located at the center of the Tx and Rx parts, and the second step calculates the specular reflectance defined by the specular reflection power (i.e., intensity) of the MUT normalized to that of the metal plate. Multiple reflection effects between the Tx and Rx antennas and the MUT on the measured specular reflectance are minimized by averaging out the multiple specular reflectances measured with changing the separation distance between the two antennas by ${\lambda}/8$ intervals. Measurement results of the perpendicular-polarized specular reflectance of commonly used dielectric plates are verified by comparing those with the analytic results and show that the results measured over the overlapped frequency range of the D-/G-bands and at the boundary frequency of the G-/J-bands agree well with the results for the other band, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.447-450
• /
• 2009

In this paper, binary pulse-antipodal modulation (2PAM) direct-sequence (DS) ultra-wideband (UWB) system is applied to multiple input multiple output (MIMO) system using vertical bell lab layered space-time (V-BLAST) structure to achieve high-data-rate communications over indoor wireless channels. The relationship between antenna dimension and BER performance of 2PAM DS UWB MIMO system is discussed. In the receiver of UWB-MIMO system, various MIMO detection algorithms such as zero-forcing (ZF), ZF-ordered successive interference cancellation (OSIC), minimum-mean-square-error (MMSE), MMSE-OSIC and maximum likelihood (ML) are comparatively studied.

• Journal of KIISE:Information Networking
• /
• v.33 no.1
• /
• pp.16-27
• /
• 2006

The wireless transmission medium inherently broadcasts a signal to all neighbor nodes in the transmission range. Existing asynchronous MAC protocols do not provide a concrete solution for reliable broadcast in link layer. This mainly comes from that an omni-directional broadcasting causes to reduce the network performance due to the explosive collisions and contentions. This paper proposes a reliable broadcast protocol in link taller based on directional antennas, named MDB(MAC protocol for Directional Broadcasting). This protocol makes use of DAST(Directional Antennas Statement Table) information and D-MACA(Directional Multiple Access and Collision Avoidance) scheme through 4-way handshake to resolve the many collision problem wit]1 omni-directional antenna. To analyze its performance, MDB protocol is compared with IEEE 802.11 DCF protocol [9] and the protocol 2 of reference [3], in terms of the success rate of broadcast and the collision rate. As a result of performance analysis through simulation, it was confirmed that the collision rate of the MDB protocol is lower than those of IEEE 802.11 and the protocol 2 of reference [3], and that the completion rate of broadcast of MDB protocol is higher than those of IEEE 802.11 and the protocol 2 of reference [3].

• Journal of IKEEE
• /
• v.16 no.3
• /
• pp.159-166
• /
• 2012

In this paper, we designed and implemented the MIMO (Multiple-Input Multiple-Output) antenna for the mobile handset that could be used for multiple services. Simulation results were obtained using SEMCAD X by SPEAG based on the FDTD (Finite Difference Time Domain) Method which showed that S11 values were less than -6 dB (VSWR < 3) for LTE (Long Term Evolution) 700/2300/2500, K-PCS (Korea-Personal Communication Service : 1,750 ~ 1,870 MHz), US-PCS (US-Personal Communication Service : 1,850 ~ 1,990 MHz), Wibro (2,300 ~ 2,390 MHz), Bluetooth (2,400 ~ 2,483 MHz), and US-WiMAX (US-World interoperability for Microwave Access: 2,400 ~ 2,590 MHz) frequency bands. Measured results of the fabricated antenna also showed that it could be used for LTE 700/2300/2500, K-PCS, US-PCS, Wibro, Bluetooth, and US-WiMAX. services.