• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.7 s.98
• /
• pp.690-696
• /
• 2005

It is very important to reduce the PAPR(Peak to Average Power Ratio) in the OFDM(Orthogonal Frequency Division Multiplexing) communication system. The proposed method in this paper is an effective PAPR reduction method using the Golay complementary codes without my side information. There are some PAPR reduction methods with the complementary code pairs or sequences. They are usually a type of the forward ewer correction codes so that they produce more redundancies and lower down the code rate. Because of this, the information rate may be cut down or more bandwidth must be required. In this paper, we propose a PAPR reduction method that uses the multi-phase complementary code f3r converting the 4-QAM into 16-QAM constellation. It does not change the code rate and does not require the side information.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.146-153
• /
• 2008

In this paper, a integrated phase-locked loop(PLL) as a clock multiphase generator for a high speed serial link is designed. The designed PLL keeps the same bandwidth and damping factor by using programmable current mirror in the whole operation frequency range. Also, the close-loop transfer function and VCO's phase-noise transfer function of the designed PLL are obtained with circuit netlists. The self impedance on board-mounted chip is calculated according to sizes and positions of decoupling capacitors. Especially, the detailed self-impedance analysis is carried out between frequency ranges represented the maximum gain in the close-loop transfer function and the maximum gain in the VCO's phase noise transfer function. We shows PLL's jitter characteristics by decoupling capacitor's sizes and positions from this result. The designed PLL has the wide operating range of 0.4GHz to 2GHz in operating voltage of 1.8V and it is designed 0.18-um CMOS process. The reference clock is 100MHz and PLL power consumption is 17.28mW in 1.2GHz.

• Journal of the Korean Institute of Gas
• /
• v.17 no.1
• /
• pp.26-34
• /
• 2013

The multiphase flow analysis related to phase change can be adapted to lots of areas such as evaporation and condensation has many interesting branches due to complicated phenomenon. In this study, the experimental investigation of cryogenic liquid in the porous media with various densities was shown how the cryogenic liquid behaves in the porous structure. For this study, permeability behaviors under different applying pressure of the glass wool with different bulk densities are discussed. Experimental investigation on the behavior of cryogenic liquefied nitrogen in the porous media is conducted. The result was that the non linearity of pressure gradient with location is increased and the permeability is decreased as the bulk density of glass wool increased. Lastly, simulation results with CFD commercial package program are used to realize the cryogenic liquid's flow in porous media to compare the finding with experimental results.

• Structural Engineering and Mechanics
• /
• v.66 no.4
• /
• pp.505-513
• /
• 2018

Steam flooding is widely used in heavy oil reservoir with coupling effects among the formation temperature change, fluid flow and solid deformation. The effective stress, porosity and permeability in this process can be affected by the multi-physical coupling of thermal, hydraulic and mechanical processes (THM), resulting in a complex interaction of geomechanical effects and multiphase flow in the porous media. Quantification of the state of deformation and stress in the reservoir is therefore essential for the correct prediction of reservoir efficiency and productivity. This paper presents a coupled fluid flow, thermal and geomechanical model employing a program (MATLAB interface code), which was developed to couple conventional reservoir (ECLIPSE) and geomechanical (ABAQUS) simulators for coupled THM processes in multiphase reservoir modeling. In each simulation cycle, time dependent reservoir pressure and temperature fields obtained from three dimensional compositional reservoir models were transferred into finite element reservoir geomechanical models in ABAQUS as multi-phase flow in deforming reservoirs cannot be performed within ABAQUS and new porosity and permeability are obtained using volumetric strains for the next analysis step. Finally, the proposed approach is illustrated on a complex coupled problem related to steam flooding in an oil reservoir. The reservoir coupled study showed that permeability and porosity increase during the injection scenario and increasing rate around injection wells exceed those of other similar comparable cases. Also, during injection, the uplift occurred very fast just above the injection wells resulting in plastic deformation.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.6
• /
• pp.470-475
• /
• 2017

Since the intake air of gas turbine engine of marine purpose contains water particles, inertial separator for separating the air and water particles are provided. Saw type and wave type separator are now used to separate inflow water particle from the gas. In this paper, the design parameters of saw type separator are studied by numerical simulations. Using the commercial CFD program, Star-CCM+, Lagrangian-Eulerian method was used to perform the analysis of two phase flow of the mist in the air. This method solves Reynolds-Averaged Navier-Stokes equations in Eulerian framework for the continuous phase, while solves equation of motion for individual particles in Lagrangian framework. Lagrangian multiphase method was applied to monitor the particles of different sizes and shapes and to verify collision between particles by chasing particles. Water particles were injected through injectors located at the inlet of the separator and escape mode was used which assumes that the particles attached on the surface of inertial separator were removed from the simulation, effectively escaping the solution domain. Through the numerical computations with the inlet condition of constant water particle size in the wetness fraction of 85%, efficiency of eliminating the water particle and the pressure drop between the inlet and outlet were examined.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.2
• /
• pp.55-64
• /
• 2015

In this study, a 3-D flame cooling analysis is conducted to examine thermal safety for the flame deflector of the 75 tonf class propulsion test facility, and the safe discharge of the exhaust gas is assessed by using numerical results. The Mixture multiphase model is adopted for the simulation of heat transfer and phase exchange process between flame and cooling water, and the computational study using the single species unreacted model for the exhaust plume is carried out for the flame cooling. Numerical analysis predicts maximum temperature on the flame deflector wall for different water flow rates, and evaluates the safe minimum flow rate of water corresponding to the fire-resistant temperature for concrete.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.6
• /
• pp.1972-1978
• /
• 2012

The polymer of (2,2-dimethyl-1,3-propanediaminebis(salicylideneaminato))-nickel(II), Ni(saldMp), was deposited on multi-walled carbon nanotubes (MWCNTs) substrate by the route of potential linear sweep. The nano structures of poly[Ni(saldMp)] have been obtained by adjusting the monomer concentration of 0.1, 0.2, 0.5, 1.0 and 1.5 mmol $L^{-1}$. The poly[Ni(saldMp)] prepared in acetonitrile solution with monomer concentration of 1.0 mmol $L^{-1}$ shows the fastest growth rate. The effects of potential window on charge-discharge efficiency and electrodeposition scan number on capacitance performance were discussed. Poly[Ni(saldMp)] prepared with less electrodeposition scans exhibits higher capacitance, but this goes against the improvement of the whole electrode capacitance. Sample with 8 deposition scans is the best compromise with the geometric specific capacitance 3.53 times as high as that of pure MWCNTs, and 1.24 times for the gravimetric specific capacitance under the test potential window 0.0-1.0 V.

• Nuclear Engineering and Technology
• /
• v.47 no.6
• /
• pp.700-711
• /
• 2015

Sodium-cooled fast breeder reactors use liquid sodium as a moderator and coolant to transfer heat from the reactor core. The main hazard associated with sodium is its rapid reaction with water. Sodium-water reaction (SWR) takes place when water or vapor leak into the sodium side through a crack on a heat-transfer tube in a steam generator. If the SWR continues for some time, the SWR will damage the surface of the defective area, causing it to enlarge. This self-enlargement of the crack is called "self-wastage phenomena." A stepwise numerical evaluation model of the self-wastage phenomena was devised using a computational code of multicomponent multiphase flow involving a sodium-water chemical reaction: sodiumwater reaction analysis physics of interdisciplinary multiphase flow (SERAPHIM). The temperature of gas mixture and the concentration of NaOH at the surface of the tube wall are obtained by a numerical calculation using SERAPHIM. Averaged thermophysical properties are used to assess the local wastage depth at the tube surface. By reflecting the wastage depth to the computational grid, the self-wastage phenomena are evaluated. A two-dimensional benchmark analysis of an SWAT (Sodium-Water reAction Test rig) experiment is carried out to evaluate the feasibility of the numerical model. Numerical results show that the geometry and scale of enlarged cracks show good agreement with the experimental result. Enlarged cracks appear to taper inward to a significantly smaller opening on the inside of the tube wall. The enlarged outer diameter of the crack is 4.72 mm, which shows good agreement with the experimental data (4.96 mm).

• Coupled systems mechanics
• /
• v.8 no.4
• /
• pp.339-350
• /
• 2019

A numerical simulation of the incompressible multiphase hydraulic jump flow was performed to compare the interface prediction through the use of the three RANS turbulence models: $k-{\varepsilon}$, $RNGk-{\varepsilon}$ and SST $k-{\omega}$. A three dimensional no submerged hydraulic jump and a two dimensional submerged hydraulic jump were modeled. Both the geometry and the mesh were created using the open source Gmsh code. The project's geometry consists of a rectangular channel with length and height differences between the two dimensional and three dimensional simulations. Uniform hexahedral cells were used for the mesh. Three refining meshes were constructed to allow to verify simulation convergence. The Volume of Fluid (abbr. VOF) method was used for treatment of the air-water surface. The turbulence models were evaluated in three distinct set up configurations to provide a greater accuracy in the flow representation. In the two-dimensional analysis of a submerged hydraulic jump simulation, the turbulence model RNG RNG $k-{\varepsilon}$ provided a better interface adjust with the experimental results than the model $k-{\varepsilon}$ and SST $k-{\omega}$. In the three-dimensional simulation of a no-submerged hydraulic jump the k-# showed better results than the SST $k-{\omega}$ and RNG $k-{\varepsilon}$ capturing the height and length of the ledge with a better fit with the experimental results.

• Journal of the military operations research society of Korea
• /
• v.5 no.1
• /
• pp.155-162
• /
• 1979

GERT modeling is in a dynamic stage of development. One of the most exciting and useful new developments in GERT modeling and Simulation is the modeling technology and computer package called Q-GERT. As the name implies, this provides the capability to analyze complex networks of queueing systems. The modeling approach is quite similar to GERT, but includes queue nodes called 'Select' nodes, which allow a considerable amount of logic to be included in the analysis of complex networks of multichannel, multiphase queueing systems should find the Q-OERT package of considerable interest.