• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.97-103
• /
• 2002

Vibration isolation technology using an air spring and laminated rubber bearing is widely used because it has excellent vibration isolation characteristics. In the part of that, we usually make use of the self-damped air suing. It is occupied two chambers, restrictor, diaphragm and load plate. Two chambers contain compressed air and the volume of chambers and the area of load plate give a definition of stiffness and load. The restrictor and the volume ratio of two chambers give a definition of damping ratio. The conventional model of restrictor is made of one orifice and it causes turbulent flow in the orifice at the region of large deflection. The stillness of air suing is larger and the damping is lower in the region of large deflection. In the multi-orifice case, the stiffness is similar to air spring with one orifice but damping ratio is larger than conventional air spring. And damping ratio is smaller than conventional air suing in small deflection region. Deflection is small in the region of high frequency so small damping is better than large damping. As a result, we can reduce the storage stiffness of air suing in the wide region of deflection and increase the damping ratio in the region of large deflection. After this, we will try to and the relation of Reynolds Number and Flow Resistance then we are going to make another restrictor for air spring to improve damping ratio and stiffness.

• Journal of the Korean Society of Safety
• /
• v.25 no.3
• /
• pp.15-21
• /
• 2010

A differential case equipped with LSD(limited slip differential) has several advantages over a normal type for rear wheel drive vehicles. Specially, the torque distribution can be done between left and right drive wheel in the state of limited slip differential. Also although LSD types are very various according to operating type, medium and torque distribution, a multi-clutch type is generally applied to rear wheel drive vehicles. So, this study presents the analysis of design parameters for development of a friction plate for multi-clutch type LSD using vehicle road test, the simulation of analytical model and the development of vehicle dynamics model by a benchmark product. According to this investigation, the design parameters which are pre-load of coil spring, friction plate and contact area quantity, friction coefficient and TBR(torque bias ratio) for a friction plate are derived from experiment and simulation and consequently, vehicle dynamics model has been constructed for the development of friction plate for multi-clutch type LSD.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.10a
• /
• pp.593-602
• /
• 2006

대구경 현장타설말뚝에 대한 시험하중의 증가와 함께 적용이 활성화되고 있는 오스터버그 셀(Osterberg cell)방식이 적용된 국외의 4 개소 시험결과에 대하여 소개하였다. 사례연구의 대상이 된 4 개소 시험말뚝은 일반적인 시험보다는 결과상의 특징이 있어 현재 및 향후 동일한 시험방법이 적용될 경우 고려될 수 있는 내용을 중심으로 기술하였다. 이들 말뚝시험에서는 가장 전형적으로 지지력의 균형이 이루어져 말뚝의 극한현상이 발생되지 않아 설계하중을 충분히 확인한 경우뿐 아니라 선단지지력이 부족하여 선단 그라우팅 후 재시험을 한 경우, O-cell을 말뚝의 선단에 가장 근접하여 설치 한 후 시험한 경우, 그리고 다단면(multi-level test)시험이 수행되었던 예 등을 살펴보았다.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.5
• /
• pp.698-704
• /
• 2012

This paper proposes a new methodology for evaluating the probabilistic reliability based grid expansion planning of composite power system including the Wind Turbine Generators. The proposed model includes capacity limitations and uncertainties of the generators and transmission lines. It proposes to handle the uncertainties of system elements (generators, lines, transformers and wind resources of WTG, etc.) by a Composite power system Equivalent Load Duration Curve (CMELDC)-based model considering wind turbine generators (WTG). The model is derived from a nodal equivalent load duration curve based on an effective nodal load model including WTGs. Several scenarios are used to choose the optimal solution among various scenarios featuring new candidate lines. The characteristics and effectiveness of this simulation model are illustrated by case study using Jeju power system in South Korea.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.8
• /
• pp.2875-2893
• /
• 2015

Existing coding aware routing algorithms focused on novel routing metric design that captures the characteristics of network coding. However, in packet coding algorithm, they use opportunistic coding scheme which didn't consider the queue state of the coding node and are equivalent to the conventional store-and-forward method in light traffic load condition because they never delay packets and there are no packets in the output queue of coding node, which results in no coding opportunity. In addition, most of the existing algorithms assume that all flows participating in the network have equal rate. This is unrealistic since multi-rate environments are often appeared. To overcome above problem and expand network coding to light traffic load scenarios, we present an enhanced coding-aware routing algorithm based on queue state and local topology (OQMCAR), which consider the queue state of coding node in packet coding algorithm where the control policy is of threshold-type. OQMCAR is a unified framework to merge single rate case and multiple rate case, including the light traffic load scenarios. Simulations results show that our scheme can achieve higher throughput and lower end-to-end delay than the current mechanisms using COPE-type opportunistic coding policy in different cases.

• Journal of Aerospace System Engineering
• /
• v.13 no.5
• /
• pp.57-64
• /
• 2019

Recently, avionics systems are being developed as integrated modular architecture applying the modular integration design of the functional unit to reduce maintenance costs and increase operating performance. Additionally, a partitioning operating system based on virtualization technology was used to process various mission control functions. In virtualization technology, the CPU processing load distribution is a key consideration. Especially, the uncertainty of the I/O processing time is a risk factor in the design of reliable avionics systems. In this paper, we examine the influence of the I/O processing method by comparing and analyzing the CPU processing load by the I/O processing method through use of case analysis and applying it to the example of spatial-temporal partitioning.

• Journal of Advanced Marine Engineering and Technology
• /
• v.12 no.2
• /
• pp.35-45
• /
• 1988

In this paper an experimental review of condition monitoring method using time domain vibration signals and statically measured wave forms of a multi-components damaged ball bearing is presented first time. Many investigators studied already about vibration characteristics of a single point damaged ball bearing but they did not make efforts to verify vibration phenomena of a multi-components damaged one. Even in case of a tripple components damaged (i.e, outer race, inner race and rolling element) one, the high frequency resonance technique (HERT) and the displacement time domain technique can be also used for its fault detection. According to experimental results undertaken a static displacement measuring method, the defect locations of components can be proposed confidently with simple calculation of the rotating angles of each component.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1990.04a
• /
• pp.186-194
• /
• 1990

Just-In-Time production is to keep the kanban system. When production managers implement and operate successfully the system in the multi-Line, multi-stage production setting, it is very important to determine the number of kanbans in deterministic kanban system under consideration with relevant factors as well as with cost. In concrete, we discuss about following factors in kanban system and provide a model formulating the multi-objective goal programming : Demand, stock on hand in process, Inventory cost and Labor cost, Vendor's suppling capacity, Work Load. Finally we analyze several numerical examples in order to test the model and attempt to expand the model in general case.

• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.200-202
• /
• 1999

This paper describes the optimization problem of real power rescheduling and present an algorithm based linear programming for studying the load-shedding and generation reallocation problem when a portion of the transmission system is disabled and at power flow solution cannot be obtained for the overload of some lines. And in case initial is infeasible, solution could not be converge. So this paper gives an algorithm being lie infeasible quantities within limit. The paper describes a LP-based algorithm to obtain the solution in power dispatch related to overload situations in power system and it is easily extened under various objective. The optimization procedures is based in linear programming with bounded variables and use the multi-segment curve method for a objective function and the validity of the algorithm is verified with two examples : 10-bus system and 57-bus system.

• Journal of Construction Engineering and Project Management
• /
• v.5 no.4
• /
• pp.16-22
• /
• 2015

This paper presents an automated computer vision-based system to update BIM data by leveraging multi-modal visual data collected from existing buildings under inspection. Currently, visual inspections are conducted for building envelopes or mechanical systems, and auditors analyze energy-related contextual information to examine if their performance is maintained as expected by the design. By translating 3D surface thermal profiles into energy performance metrics such as actual R-values at point-level and by mapping such properties to the associated BIM elements using XML Document Object Model (DOM), the proposed method shortens the energy performance modeling gap between the architectural information in the as-designed BIM and the as-is building condition, which improve the reliability of building energy analysis. Several case studies were conducted to experimentally evaluate their impact on BIM-based energy analysis to calculate energy load. The experimental results on existing buildings show that (1) the point-level thermography-based thermal resistance measurement can be automatically matched with the associated BIM elements; and (2) their corresponding thermal properties are automatically updated in gbXML schema. This paper provides practitioners with insight to uncover the fundamentals of how multi-modal visual data can be used to improve the accuracy of building energy modeling for retrofit analysis. Open research challenges and lessons learned from real-world case studies are discussed in detail.