• Journal of Broadcast Engineering
• /
• v.11 no.4 s.33
• /
• pp.533-540
• /
• 2006

In this study we propose to use a facial motion capture technique to track facial motions and expressions effectively by using the stereo vision module, which has two CMOS IMAGE SENSORS. In the proposed tracking algorithm, a center point tracking technique and correlation tracking technique, based on neural networks, were used. Experimental results show that the two tracking techniques using stereo vision motion capture are able to track general face expressions at a 95.6% and 99.6% success rate, for 15 frames and 30 frames, respectively. However, the tracking success rates(82.7%,99.1%) of the center point tracking technique was far higher than those(78.7%,92.7%) of the correlation tracking technique, when lips trembled.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1603-1605
• /
• 2001

Eight 300kJ modularized capacitor-banks have been constructed. These modules have been installed and assembled to make a 2.4MJ pulse power system (PPS). This 2.4MJ PPS was developed to be used as a driver of an electrothermal-chemical (ETC) gun. Each capacitor bank has six 22kV, 50kJ capacitors connected in parallel. A triggered vacuum switch (TVS-43) was adopted as a main pulse power-closing switch in each module. The module also contains a crowbar circuit made of three high-voltage diode-stacks, a multi-tap inductor and an energy-dumping resistor. Various current shapes have been formed by a sequential firing of multiple capacitor banks. Resistive dummy load has been used and various combinations of experimental parameters, such as charging voltage, trigger time and inductance, were tested to make flexible current shapes.

• ETRI Journal
• /
• v.38 no.3
• /
• pp.417-424
• /
• 2016

In this paper, an accurate characterization of a fabricated X-band transmit/receive module is described with the process of generating control data to correct amplitude and phase deviations in an active electronically scanned array antenna unit. In the characterization, quantization errors (from both a digitally controlled attenuator and a phase shifter) are considered using not theoretical values (due to discrete sets of amplitude and phase states) but measured values (of which implementation errors are a part). By using the presented procedure for the characterization, each initial control bit of both the attenuator and the phase shifter is closest to the required value for each array element position. In addition, each compensated control bit for the parasitic cross effect between amplitude and phase control is decided using the same procedure. Reduction of the peak sidelobe level of an array antenna is presented as an example to validate the proposed procedure.

• Steel and Composite Structures
• /
• v.20 no.5
• /
• pp.1133-1153
• /
• 2016

In this article, an additive performance ratio method using structural analysis of both 2D and 3D is introduced to mitigate the complexity of work evaluating structural performances of numerous steel outrigger alternatives in multi-story buildings, especially high-rise buildings. The combined structural analysis process enables to be the design of economic, safe, and as constructional demanding structures by exploiting the advantages of steel, namely: excellent energy dissipation and ductility. First the approach decides the alternative of numerous steel outriggers by a simple 2D analysis module and then the alternative is evaluated by 3D analysis module. Initial structural analyses of outrigger types are carried out through MIDAS Gen 2D modeling, approximately, and then the results appeal structural performance and lead to decide some alternative of outrigger types. ETABS 3D modeling is used with respect to realization and evaluation of exact structural behaviors. The approach reduces computational burden in compared to existing concepts such as full 3D analysis methods. The combined 2D and 3D tools are verified by cycle and displacement tests including comprehensive nonlinear dynamic simulations. The advantages and limitations of the Additive Performance Ratio Approach are highlighted in a case study on a high rise steel-composite building, which targets at designing the optimized alternative to the existing original outrigger for lateral load resisting system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.2
• /
• pp.150-157
• /
• 2012

This paper presents CAN-based parallel-operation and load-sharing techniques for the communication server power supply. With the load information obtained through CAN communication, each modules performs its current control independently and the power unbalance caused by impedance differences of converter modules can be reduced. In conventional method, slave modules are controlled by master module. On the other hand, the proposed load share algorithm uses the Multi-Master method. Therefore, accurate load sharing can be accomplished by the reference structure of each module's average current. Each converter has two stages and it is separated into PFC, which is responsible for harmonic regulation, and LLC resonant converter, which controls output voltage. To verified the performance of the proposed method, two 2KW prototypes has been implemented and experimented.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.5B
• /
• pp.489-499
• /
• 2003

This paper is a study about Honey-pot Model using CPN(Colored Petri Nets) that is a method of intrusion detection. Suggested Honey-pot model consists of two parts : \circled1 security kernel module for active induction of hacker's intrusion, intrusion detection and behavior pattern analysis. \circled2 virtual module for activity of induced hackers. However, suggested model was compared and analysed with conventional Denning model and Shieh nodel. The Honey-pot model using CPN can classify the characteristic of intrusion pattern, modeling intrusion pattern and pattern matching procedure, detect DDoS attack through multi hosts, and provide basis of study model for analysing intrusion pattern, finally.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.3A
• /
• pp.318-323
• /
• 2004

In this paper, we present a reducing power consumption of a scheduling for reuse module selection under the time constraint. Traditional high-level synthesis do not allow reuse of complex, realistic datapath component during the task of scheduling. On the other hand, the proposed scheduling of reducing power consumption is able to approach a productivity of the design the low power to reuse which given a library of user-defined datapath component and to share of resource sharing on the switching activity in a shared resource. Also, we are obtainable the optimal the scheduling result in experimental results of our approach various HLS benchmark environment using chaining and multi-cycling in the scheduling techniques.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.4
• /
• pp.131-138
• /
• 2011

We fabricated distributed feedback InGaAsP/InP laser diodes for optical fiber communication module and characterized the lasing properties in continuous wave operation. The active layer of 7-period InGaAsP(1.127 eV)/InGaAsP(0.954 eV) multi-quantum well structure was grown by the metal-organic chemical vapor deposition. The grating for waveguide was also fabricated by the implementation of the Mach-Zehender holographic method of two laser beams interference of He- Cd laser and the fabricated laser diode has the dimension of the laser length of $400{\mu}m$ and the ridge width of $1.2{\mu}m$. The laser diode shows the threshold current of 3.59 mA, the threshold voltage of 1.059 V. For the room-temperature operation with the current of 13.54 mA and the voltage of 1.12 V, the peak wavelength is about 1309.70 nm and optical power is 13.254 mW.

• The Journal of the Korea Contents Association
• /
• v.6 no.11
• /
• pp.225-234
• /
• 2006

In this paper, we design a combined security processor, ECC, MD-5, and AES, as a SIP for cryptography of securing contents. Each SIP is modeled and designed in VHDL and implemented as a reusable macro through logic synthesis, simulation and FPGA verification. To communicate with an ARM9 core, we design a BFM(Bus Functional Model) according to AMBA AHB specification. The combined security SIP for a platform-based SoC is implemented by integrating ECC, AES and MD-5 using the design kit including the ARM9 RISC core, one million-gate FPGA. Finally, it is fabricated into a MPW chip using Magna chip $0.25{\mu}m(4.7mm{\times}4.7mm$) CMOS technology.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.8A
• /
• pp.657-662
• /
• 2003

The OPM(optical performance monitoring module) is needed in order to monitor optical performance. the most importance of OPM is to measure the wavelength of optical signal. In the past time, it was very difficult to get the wavelength value because they used pilot tone. Since then, using AWG(arrayed waveguide grating) and AOTF(acousto optic tuneable filter), the wavelength and the transmission qualify for multi channel signal have been monitored. In this paper, we chose the fiber fabry-perot wavelength variable filter which be evaluated for optical resolution ability to excellent, so that FBG(fiber bragg grating) was used for setting reference wavelength because chose a wavelength variable filter.