• Korean Journal of Veterinary Research
• /
• v.41 no.4
• /
• pp.485-495
• /
• 2001

It was investigated whether $Ca^{2+}$ and $K^+$ channels were involved in the inhibitory action of nitric oxide (NO) on the contractile and slow wave activity of guinea pig gastric antral circular muscle. The gastric antral circular muscle showed spontaneous phasic contraction and slow wave. NO donors, 3-morpholinosydnonimine hydrochloride (SIN-1, $0.01{\sim}100{\mu}M$) and S-nitroso-L-cysteine (CysNO, $0.001{\sim}10{\mu}M$), reduced not only the amplitude of phasic contraction but also that of slow wave in a concentration-dependent manner. Both the perfusion of $Ca^{2+}$-free solution and the administration of $Ni^{2+}$, a nonselective $Ca^{2+}$ channel blocker, reduced the phasic contraction as well as the amplitude and frequency of the slow wave. The effects of these treatments were similar to those of NO donors. Nifedipine ($10{\mu}M$), a specific L-type $Ca^{2+}$ channel blocker, abolished the phasic contraction and remarkably reduced the plateau of slow wave but had no profound effect on the upstroke of slow wave. In the whole-cell patch clamp mode, CysNO shifted the steady-state activation curve for L-type $Ca^{2+}$ current to the right and the steady-state inactivation curve to the left. Pretreatment of various $K^+$ channel blockers such as tetraethylammonium (1 mM), 4-aminopyridine (0.5 mM), glibenclamide (10 mM), apamin ($0.1{\mu}M$), and iberiotoxin ($0.1{\mu}M$) did not affect the inhibitory action of SIN-1. These results suggest that NO donors suppress mechanical and electrical activity of guinea pig gastric antral circular muscle by inhibition of L-type $Ca^{2+}$ channel rather than by activation of $K^+$ channels.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1137-1140
• /
• 2002

A V-band low-noise amplifiers (LNA) based on the Millimeter-wave monolithic integrated circuit (MIMIC) technology were fabricated using high performance 0.1 $\mu\textrm{m}$ $\Gamma$-shaped pseudomorphic high electron mobility transistors (PHEMT＇s), coplanar waveguide (CPW) structures and the integrated process for passive and active devices. The low-noise designs resulted in a two-stage MIMIC LNA with a high S$\sub$21/ gain of 14.9 dB and a good matching at 60 ㎓. 20 dBm of IP3 and 3.9 dB of minimum noise figure were also obtained from the LNA. The 2-stage LNA was designed in a chip size of 2.3 ${\times}$1.4 mm$^2$by using 70 $\mu\textrm{m}$ ${\times}$2 PHEMT’s. These results demonstrate that a good low-noise performance and simultaneously with a high gain performance is achievable with GaAs PHEMT's in the 60 ㎓ band.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.304-309
• /
• 2001

With the development of electromagnetic communication technology and increased use of electromagnetic wave, the countermeasure of EMI(Electromagnetic Interference) becomes more important socially, and interest for the electromagnetic wave absorber has also increased. In this paper, we have studied characteristics of frequency dependency on complex permittivity and complex permeability according to the changes of composition rate and sintering temperature of NiCuZn ferrite also known as electromagnetic wave absorber and further looked into effect of electromagnetic wave absorption properties. From the measurement where the composition of Fe$_2$O$_3$ and ZnO of NiCuZn ferrite was fixed at 49 and 34 mol% respectively while composition of NiO and CuO has been varied at each test, we found out that initial permeability and permittivity were high and the absorbing ability of electromagnetic wave recorded best with loss tangent(${\mu}$r"/${\mu}$r′) displays more than 1 within the frequency band of 2MHz～9.5MHz when the composition ratio of NiO was ranged around 8.5～9.5 mol% and the sintering temperature was 1,080$^{\circ}C$.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.42 no.2
• /
• pp.141-145
• /
• 1997

The long wave infrared which is ranged to 4～1, 000 ${\mu}{\textrm}{m}$ is a kind of electromagnetic wave, and the wave is being absorbed by higher plant easily. The absorbed wave in the plant promotes the metabolism of plant cell by way of resonance with the water molecules of plant cell. This experiment was carried out to determine the effect of long wave infrared radiation ceramic on growth of rice seedling, and to make the optimum mixture rate of ceramic powder when ceramics was mixed with bed soil at 4, 8, 12, 16％ levels for machine transplanting. The results of this study indicate that the growth of the seedling significantly higher in the treatment sites than that of control sites. However, there was no significant differences in dry matter weight between the treatment and control sites. At the 9.6％ mixing ratio, the highest growth of rice seedling was found.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.5 s.335
• /
• pp.61-68
• /
• 2005

In this paper, low conversion loss 94 GHz MIMIC resistive mixer was designed and fabricated. The $0.1{\mu}m$ InGaAs/InAlAs/GaAs Metamorphic HEMT, which is applicable to MIMIC's, was fabricated. The DC characteristics of MHEMT are 665 mA/mm of drain current density, 691 mS/mm of maximum transconductance. The current gain cut-off frequency(fT) is 189 GHz and the maximum oscillation frequency(fmax) is 334 GHz. A 94 GHz resistive mixer was fabricated using $0.1{\mu}m$ MHEMT MIMIC process. From the measurement, the conversion loss of the 94 GHz resistive mixer was 8.2 dB at an LO power of 10 dBm. P1 dB(1 dB compression point) of input and output were 9 dBm and 0 dBm, respectively. LO-RF isolations of resistive mixer was obtained 15.6 dB at 94.03 GHz. We obtained in this study a lower conversion loss compared to some other resistive mixers in W-band frequencies.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.5
• /
• pp.702-712
• /
• 2016

A wrist watch type wearable cardiovascular monitoring device is proposed for continuous and convenient monitoring of the patient's cardiovascular system. For comprehensive monitoring of the patient's cardiovascular system, the concurrent electrocardiogram (ECG) and arterial pulse wave (APW) sensor front-end are fabricated in $0.18{\mu}m$ CMOS technology. The ECG sensor frontend achieves 84.6-dB CMRR and $2.3-{\mu}Vrms$-input referred noise with $30-{\mu}W$ power consumption. The APW sensor front-end achieves $3.2-V/{\Omega}$ sensitivity with accurate bio-impedance measurement lesser than 1% error, consuming only $984-{\mu}W$. The ECG and APW sensor front-end is combined with power management unit, micro controller unit (MCU), display and Bluetooth transceiver so that concurrently measured ECG and APW can be transmitted into smartphone, showing patient's cardiovascular state in real time. In order to verify operation of the cardiovascular monitoring system, cardiovascular indicator is extracted from the healthy volunteer. As a result, 5.74 m/second-pulse wave velocity (PWV), 79.1 beats/minute-heart rate (HR) and positive slope of b-d peak-accelerated arterial pulse wave (AAPW) are achieved, showing the volunteer's healthy cardiovascular state.

• Korean Journal of Optics and Photonics
• /
• v.30 no.1
• /
• pp.15-22
• /
• 2019

$Si_3N_4$ rib-optical waveguides for evanescent-wave integrated-optical biosensors were analytically interpreted, to derive the single-mode propagation conditions. The integrated-optical biosensor structure based on two-mode interference was proposed, and the rib width and thickness and core thickness for a single-mode and two-mode waveguide (sensing region) were proposed to be $3{\mu}m$, 2 nm, and 150 nm and $3{\mu}m$, 20 nm, and 340 nm respectively. The optical characteristics of each guided-wave mode were investigated utilizing the film mode-matching (FMM) analysis.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.26-29
• /
• 1987

This paper concerns methods for ${\mu}$-wave imaging. The image reconstruction of an object by range-doppler preceding using the X-Band Linear-FM signal is presented from tile simulated data. The high degree of range resolution is achived using large signal band width and cross-range resolution is obtained by doppler processing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.11a
• /
• pp.71-74
• /
• 1993

In this paper, the permeability(${\mu}$$\sub$r′/, ${\mu}$$\sub$r"/), permittivity($\varepsilon$$\sub$r′/, $\varepsilon$$\sub$r"/) and absorption properties of Ferroxplana/Rubber composites were investigated. The composite specimens were prepared by molding and curing the mixtures of matrix rubber and Ni$_2$Y ferroxplana powders which were synthesized by coprecipitated method. The permeability(${\mu}$$\sub$r′/) of specimen was decreased in the range of 8∼12.5(GHz) and the permeability(${\mu}$$\sub$r"/) and Permittivity($\varepsilon$$\sub$r′/, $\varepsilon$$\sub$r"/) were increased. The optimum thickness of electromagnetic wave absorber (F/R=4, 1,200($^{\circ}C$) ), utilizing the Smith chart, was about 3.0(mm). The Figure of Merit was 93(%).

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.8
• /
• pp.140-152
• /
• 1995

Derived was the scalar wave equation of optical fibers. Based on the derived equation, the dispersion characteristics of arbitrarily profiled fibers were analyzed. We applied the 1-D FEM employing quadratic interpolation fucntions to solve the scalar wave equation. To find the optimum index distribution of a fiber that has the ultra-low total dispersion, we analyzed QC fibers as objects. Adding 2$_{nd}$ and 3$_{rd}$ clads to DC fiber, we investigated the change of dispersion characteristics. We found the QC fiber parameters for which the dispersion was ultra-low flattened, less than 0.5 ps/km.nm for ${\lambda}=1.4~1.6{\mu}m$, and the dispersion value was as low as 0.20 ps/km.nm at ${\lambda}=1.55{\mu}m$.