• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.7
• /
• pp.938-947
• /
• 2003

In this paper, we derived the formula for estimating the power of the electric motors needed to operate the Decanter-type centrifuge. In the derivation of the formula the sludge-removal torque is to be supplied from the formula derived in the first paper. The intricate nature of the transmission mechanism in the planetary gear trains of the sludge-removal power and torque has been clarified in this second paper. In particular we considered two-motor system, where the main motor drives the machine while the differential-speed control motor plays the role of braking in adjusting the differential speed. Sample calculation for the specific design treated in the first paper showed that the selection criterion for the main motor depends on the lower limit of the differential speed; when the lower limit is set low, it should be selected based on the steadily operating power, while it should be selected based on the starting power when the lower limit is set high. The total power required by both the main motor and the differential-speed control motor increases as the differential speed is decreased. It is suggested that the power loss in the differential-speed control motor could be minimized by attaching an electric generator to it.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.3
• /
• pp.144-149
• /
• 2011

Currently, switched reluctance motors are studied to increase energy efficient. The switched reluctance motor is possible to control higher speed and torque than the induction motors and composition is simple. Current and rotor speed are considered to install the switched reluctance motor. In this paper, Simulink model of the switched reluctance motor is suggested and the adaptive controller is applied to the model for the speed control. Asymmetry converter including the IGBT is concerned with real-time control and the speed of switched reluctance motor is controlled by installing adaptive controller.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1026-1029
• /
• 1993

Inherent speed-torque performance of Switched Reluctance Motor is similar to that of series wound DC motor. Thus, the speed of the motor is extremely regulated according to load torque. For the purpose of controlling the speed and torque of SRM it is necessary to change the applied DC link voltage or the switch-ON and switch-OFF angles which control the phase current of the motor. This paper describes speed-torque characteristics of an integral horse power Switched Reluctance Motor by adjusting the switch-ON and switch-OFF angles. Speed at rated load torque can be regulated by adjusting the switching angles and the control scheme is applied to 2kW, 3 phase, 6/4 SRM.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.6
• /
• pp.830-836
• /
• 2012

Various control algorithms have been proposed for the speed-sensorless control for an induction motor. These control schemes are mainly based on the speed feedback with the flux and speed estimations. This paper proposes another method for the speed-sensorless control for an induction motor. The proposed scheme is based on the torque and flux compensation without speed estimations, in which the same controlled stator voltage is applied to both the induction motor and the numerical model so that the differences between torques and fluxes of the model and the induction motor may be compelled to give access to zero. The results of experiment show the effectiveness of the scheme.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.387-392
• /
• 1999

The micro electronic control technology with developing microcomputers make great contribution to electrohydraulic control systems. The electrohydraulic pulse control simplifies in conjunction with power electronic amplifier and high speed operated solenoid valves. It is necessary to valves to convert electronic pulse signal to hydraulic pulse flow as fast as possible. This study deals with the speed control of an oil hydraulic motor operated by two way high speed solenoid valves. The valves acts as converters of electronic-pulse signals to hydraulic power. By constructing systems in which a hydraulic motor is operated by two solenoid valves, the pulse with modulation method (PWM) has adopted as the speed control of hydraulic motor systems. The static and dynamic characteristics of the systems are investigated by the experiment. It is clarify that a hydraulic motor operated PWM show good performance as a control component, achieving accurate velocity control.

• Journal of Power Electronics
• /
• v.12 no.2
• /
• pp.305-316
• /
• 2012

The paper presents an accurate loss model based controller of an induction motor to calculate the optimal air gap flux. The model includes copper losses, iron losses, harmonic losses, friction and windage losses, and stray losses. These losses are represented as a function of the air gap flux. By using the calculated optimal air gap flux compared with rated flux for speed sensorless indirect vector controlled induction motor, an improvement in motor efficiency is achieved. The motor speed performance is improved using a fuzzy logic speed controller instead of a PI controller. The fuzzy logic speed controller was simulated using the fuzzy control interface block of MATLAB/SIMULINK program. The control algorithm is experimentally tested within a PC under RTAI-Linux. The simulation and experimental results show the improvement in motor efficiency and speed performance.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.8
• /
• pp.545-550
• /
• 2004

This paper is proposed a fuzzy neural network controller based on the vector controlled induction motor drive system. The hybrid combination of fuzzy control and neural network will produce a powerful representation flexibility and numerical processing capability. Also, this paper is proposed estimation and control of speed of induction motor using ANN Controller. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. The error between the desired state variable and the actual one is back-propagated to adjust the rotor speed, so that the actual state variable will coincide with the desired one. The back propagation mechanism is easy to derive and the estimated speed tracks precisely the actual motor speed. This paper is proposed the theoretical analysis as well as the simulation results to verify the effectiveness of the new method.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.9
• /
• pp.36-46
• /
• 1994

A analog disturbance observer, which is suitable for servo motor drive, was employed to suppressi control of the impact drop disturbance. The main advantage of the observer is that a fast response disturbance estimation is obtained using the detected motor cuttent and speed. And the new M/T method for motor speed detection is proposed. The method should be able to reduce the detection dead time compared with the Ohmae's M/T method. Also, the low speed control of a servo motor using instantaneous speed detection method is described. To estimate the instantaneous speed from the average speed, the speed estimator of the first order is proposed. Actually we confirmed that these methods improve the speed control performance of the servo system with experiments.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2203-2205
• /
• 2003

In this thesis, it is a purpose to carry out speed control of DC servo motor without using encoder and the resolver which are speed sensor of DC servo motor and it should use estimate algorithm or observer and must assume a speed in order to control speed sensorless. Therefore, high gain observer was designed to estimate rotor speed of DC servo motor and it carries out speed control from the feedback of the speed that assumed done in the thesis. Also, implementation used easy PI controller in speed-controller of DC motor though it was simple. It is compared estimate performance of Luenberger and high gain observer in a way of computer simulation in order to verify performance of the high gain observer which proposed in this thesis, and proved excellency of the high gain observer. And the thesis proved that smooth speed sensorless control of DC servo motor was implemented in invariable driving.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.5
• /
• pp.2040-2045
• /
• 2015

This paper deals with the electromagnetic and thermal analysis of high speed induction motor. The induction motor is analyzed by time-varying magnetic finite element method and its thermal analysis is carried out by using analytical lumped-circuit method. Analysis results are compared with the experiment of 29kW high speed motor prototype at 12,000rpm.