• Korean Chemical Engineering Research
• /
• v.46 no.2
• /
• pp.205-210
• /
• 2008

Poly(D,L-lactide-co-glycolide) (PLGA) has been widely used as carriers in controlled release delivery systems due to its biodegradability and relatively good biocompatibility. However, Release pattern of carriers fabricated using PLGA have disadvantage an initial burst within a few days, lag time several days and then sudden release changes. To solve these problems of PLGA, we fabricated PLGA wafer including monomer. Also, drug release behavior restraint sudden burst effect using recrystallization of PLGA. Recrystallized PLGA was characterized the morphological difference by SEM and in vitro release behavior measured by HPLC. The PLGA molecular weight analyzed to recognize monomer influence during degradation process of polymer using GPC. In this study, drug release duration cut short up to three days and was eliminated the lag time based on the bulk erosion.

• Korean Chemical Engineering Research
• /
• v.54 no.6
• /
• pp.806-811
• /
• 2016

Organosolv pretreatment is the process to frationation of lignocellulosic feedstocks to enhancement of enzymatic hydrolysis. This process has advantages that organic solvents are always easy to recover by distillation and recycled for pretreatment. The chemical recovery in organosolv pretreatment can isolate lignin as a solid material and carbohydrates as fermentable sugars. For the economic considerations, using of low-molecular-weight alcohols such as ethanol and methanol have been favored. When acid catalysts are added in organic solvent, the rate of delignification could be increased. Mineral acids (hydrochloric acid, sulfuric acid, and phosphoric acid) are good catalysts to accelerate delignification and xylan degradation. In this study, the biomass was pretreated using 40~50 wt% ethanol at $170{\sim}180^{\circ}C$ during 20~60 min. As a results, the enzymatic digestibility of 2-stage pretreatment of rigida using 50 wt% ethanol at $180^{\circ}C$ was 40.6% but that of 1-stage pretreatment was 55.4% on same conditions, therefore it is shown that the pretreatment using mixture of the organosolv and catalyst was effective than using them separately.

• Korean Journal of Microbiology
• /
• v.45 no.1
• /
• pp.32-40
• /
• 2009

To understand contribution of thermophilic microorganisms in decomposition of litter deposits on shore of lakes, we surveyed a lakeshore litter deposit for bacteria growing at $60^{\circ}C$. Ten thermophilic isolates were selected for in-depth characterization, based on their high capacity to degrade high molecular weight organic compounds. Based on phylogenetic analysis on their 16S rRNA gene sequences, all isolates were identified as Geobacillus. The optimal growth temperature and pH of the strains ranged $55{\sim}60^{\circ}C$ and 6.0${\sim}$8.0, respectively. Salinity was inhibitory to the growth of the isolates, showing marked decrease of growth rates at 3% salinity. Based on activities of hydrolytic enzymes and profiles of carbohydrate utilization (determined by API 50 CHB kit), three G. stearothermophilus strains showed patterns clearly distinctive from other isolates. Two G. kaustophilus strains also demonstrated distinctiveness in their metabolic pattern and ecological parameters. However, ecological and metabolic profiles of the other five isolates were more variable and showed some degree of digression from their phylogenetic classification. Therefore, it could be concluded that endospore-forming thermophilic bacteria in lakeshore litter deposits contribute to degradation of organic materials with diverse ecological niches while having successions similar to microbial flora in compost. We propose that the thermophilic isolates and/or their thermo-tolerant enzymes can be applied to industrial processes as appropriate mixtures.

• Korean Journal of Food Science and Technology
• /
• v.44 no.3
• /
• pp.274-279
• /
• 2012

The objective of this study was to develop oral matrix tablets for the sustained release of vitamin C. In this study hydroxypropyl methylcellulose (HPMC) has been utilized as an excipient, as it is one of the most widely used polymers, for use during long periods of time in formations. The vitamin C tablet formulation depends on the molecular weight and concentration of sustained-delivery in HPMC. Anti-oxidants have been added as a dissolution medium in order to prevent vitamin C degradation in water. The dissolution test was carried out in a distilled water medium, and the release model equation was applied to analyze the vitamin C release pattern. The results demonstrated that the release and lasting power of vitamin C tablets, containing HPMC, lasted for more than 12 h.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.140-140
• /
• 2018

The 3D interconnect technologies have been appeared, as the density of Integrated Circuit (IC) devices increases. Through Silicon Via (TSV) process is an important technology in the 3D interconnect technologies. And the process is used to form a vertically electrical connection through silicon dies. This TSV process has some advantages that short length of interconnection, high interconnection density, low electrical resistance, and low power consumption. Because of these advantages, TSVs could improve the device performance higher. The fabrication process of TSV has several steps such as TSV etching, insulator deposition, seed layer deposition, metallization, planarization, and assembly. Among them, TSV metallization (i.e. TSV filling) was core process in the fabrication process of TSV because TSV metallization determines the performance and reliability of the TSV interconnect. TSVs were commonly filled with metals by using the simple electrochemical deposition method. However, since the aspect ratio of TSVs was become a higher, it was easy to occur voids and copper filling of TSVs became more difficult. Using some additives like an accelerator, suppressor and leveler for the void-free filling of TSVs, deposition rate of bottom could be fast whereas deposition of side walls could be inhibited. The suppressor was adsorbed surface of via easily because of its higher molecular weight than the accelerator. However, for high aspect ratio TSV fillers, the growth of the top of via can be accelerated because the suppressor is replaced by an accelerator. The substitution of the accelerator and the suppressor caused the side wall growth and defect generation. The suppressor was used as Single additive electrodeposition of TSV to overcome the constraints. At the electrochemical deposition of high aspect ratio of TSVs, the suppressor as single additive could effectively suppress the growth of the top surface and the void-free bottom-up filling became possible. Generally, copper was used to fill TSVs since its low resistivity could reduce the RC delay of the interconnection. However, because of the large Coefficients of Thermal Expansion (CTE) mismatch between silicon and copper, stress was induced to the silicon around the TSVs at the annealing process. The Keep Out Zone (KOZ), the stressed area in the silicon, could affect carrier mobility and could cause degradation of the device performance. Cobalt can be used as an alternative material because the CTE of cobalt was lower than that of copper. Therefore, using cobalt could reduce KOZ and improve device performance. In this study, high-aspect ratio TSVs were filled with cobalt using the electrochemical deposition. And the filling performance was enhanced by using the suppressor as single additive. Electrochemical analysis explains the effect of suppressor in the cobalt filling bath and the effect of filling behavior at condition such as current type was investigated.

• Applied Chemistry for Engineering
• /
• v.7 no.3
• /
• pp.490-495
• /
• 1996

Low molecular weight linear chlorine terminated siloxanes (yields;71.2~86.5%) were prepared by reactions of cyclotri-, cyclotetra- and cyclopentasiloxane with dimethyldichlorosilane in the presence of pyridine N-oxide catalyst. The amine terminated siloxane oligomers were obtained in good yields(76.2~85.3%) by the reaction of linear chlorine terminated siloxanes with dimethylamine at $0^{\circ}C$. In this investigation, we have studied on the syntheses and properties of copolymers (yields;58.0~71.0%) obtained from the reaction of amine terminated siloxane oligomers with 1,4-bis(dimethylhydroxysilyl)benzene. The structures and properties of the copolymers were examined by FT-IR, $^1H$-NMR, TGA and DSC. Initial degradation temperatures($T_D{^i}$) of the polymer I and IV were confirmed as 476 and $485^{\circ}C$, respectively. The thermal stabilities of the polymers were found to be increased with increasing n of $(R_2SiO)_n$. The glass transition temperatures(Tg) of the polymers were increased with decreasing n of $(R_2SiO)_n$, and the lowest Tg revealed $-76^{\circ}C$ when n=5.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.52-59
• /
• 2011

L-PLA or D-PLA was synthesized in bulk at $140^{\circ}C$ by ring opening polymerization(ROP) of L-lactide or D-lactide as a monomer using tin(II) octoate and lauryl alcohol as a catalyst and an initiator with changing the amounts of catalyst(0.25~1.0 wt%) and initiator(0.l~0.5 wt%). And stereocomplex-PLA was prepared by L-PLA/D-PLA having a wide range of molecular weight(30000~90000 g/mol) and L-PLA/D-PLA blends having different mixing ratio ($X_D$). The melting temperature. thermal degradation temperature and thermal stability of stereocomplex-PLA were higher than those of homopolymers(L-PLA, D-PLA). We supposed that these improvements arose from a strong interaction between L-PLA and D-PLA. The improved mechanical properties and changes in morphology of LPLA/D-PLA blends were compared to those of homopolymers(L-PLA, D-PLA).

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.24 no.1
• /
• pp.1-11
• /
• 2018

In this study, pro-oxidant($d2w^{(R)}$) and rPP/ZnO nanocomposite flexible films for food packaging were prepared, and their mechanical and antimicrobial properties were investigated. As a result, the carbonyl index and hydroxyl index increased with exposured time to heat and UV rays. Surface analysis showed that the addition of zinc oxide improved the dispersibility and compatibility of the polymer, so that the surface of the composite film was smooth and the zinc oxide particles were smaller than the compared film. And it kept the physical properties by heat and UV ray blocking effect, and it worked to reduce decomposition. In the antimicrobial activity test, the microbial reduction rate was 3 logs or more at the use concentration of zinc oxide. The tensile strength was increased and the elongation was decreased. Oxidative degradability of multi-layered film in UV exposured for 72 hours, the molecular weight of the film decreased by 75.6%, 1,294 g/mol Mn and 5,920 g/mol Mw. In the safety analysis of food packaging materials, we obtained that are in standard of polypropylene, a food contact material of domestic law.

• Food Science of Animal Resources
• /
• v.22 no.3
• /
• pp.259-266
• /
• 2002

The egg shell membrane degrading isolated from soil was identified as Bacillus licheniformis by 16S rDNA identification method. A keratinase was isolated from the Baciilu licheniformis culture. DEAE-cellulose ion-exchange and Sephadex C-75 gel chromatograhies were used to purify the enzyme. The specific activity was increased 17.3-fold by the purification procedures. Sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) analysis and Sephadex G-75 chromatography indicated that the purified keratinase was monomeric and had a molecular weight of 65 kDa. The enzyme showed optimum activity at pH 9.0, and was stable above pH 9.0. The optimum temperature was 50$\^{C}$ and the enzyme was stable in the temperature ranges from 20$\^{C}$ to 50t. By the addition of 1 mM and 10 mM FeSO4, the activities of the enzyme were increased to 111$\pm$4.6% and 133$\pm$3.79%, respectively. The keratinase was an alkaline serine pretense because it was inhibited only by phenylmethylsulfonylfluorice (PMSF).

• The Korean Journal of Zoology
• /
• v.28 no.1
• /
• pp.31-43
• /
• 1985

The $(Ca^{2+}+Mg^{2+})$-ATPase has been purified homogeneously from sarcoplasmic reticulum of rat skeletal muscle by sucrose density gradient centrifugation. The purified enzyme has a molecular weight of 115,000 as judged by polyacrylamide gel electrophoresis in the presence of sodium dedecyl sulfate, and therefore has the same size of the enzyme in rabbit and chick skeletal muscle. $Ca^{2+}, Mg^{2+}, Fe^{2+}, Co^{2+}, and Mn^{2+}$ at 50 $\\muM$ show stimulatory effect on the ATP-ase, while $Zn^{2+}, Cu^{2+}, and Hg^{2+}$ inhibit it at the same concentration. The ATPase activity is insensitive to antimalarial drugs such as quinine and quinacrine, but is sensitive to inhibition by p-hydroxymecurie benzoate and phenylmethylsulfonylfluoride. The enzyme has optimum pH of 6 to 7 and Km value for ATP is estimated to be 98 $\\muM$. Thus, a number of biochemical properties of this enzyme appear to be different from those of the enzyme that have been isolated from rabbit skeletal muscle. The $(Ca^{2+}+Mg^{2+})$-ATPase appears to be selectively degraded in microsomal fraction. The activity of metalloendoprotease is evident in the microsomal preparation when assayed by radioactively labeled protein substrate, such as $^{3}H-casein and $^{125}I$-insulin. However, it is presently unclear whether the metalloendoprotease is responsible for the degradation of the $(Ca^{2+}+Mg^{2+})$-ATPase.