• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.4
• /
• pp.538-542
• /
• 2004

Comminuted sausages with reduced fat (25-0%) and increased moisture (19-44%) combinations were manufactured, and their chemical composition, and physico-chemical, textural and sensory properties were determined for the selection of the most palatable sausage treatment. The moisture and fat contents of the comminuted sausages varied from 55-79% and 26.4-2.14%, respectively, whereas, the protein content was relatively constant at 13.5-14.5%. Expressible moisture (EM, %) decreased with increased fat addition, and the high-fat control sausage (~25% fat) had lower EM than those with lower than 15% fat addition. Increased fat level also increased Hunter L values (lightness) of sausage samples taken from the core, and differences in lightness were observed between 15 and 25% fat level at the initial mixture. Sausages without fat addition had different textural characteristics from high-fat control sausages in most texture profile analysis (TPA) values. However, no differences in TPA values were observed among treatments with added fat (<25%) in the formulation. Results of the sensory evaluation showed that the most appropriate fat content of comminuted sausages to have better sensory properties ranged from 15-20% of added fat at the initial mixture. These results also indicated that decreased fat and increased moisture contents produce sausages with higher EM and lower lightness. Comminuted sausages without fat addition had different textural characteristics from the high-fat control.

• Journal of Biosystems Engineering
• /
• v.27 no.1
• /
• pp.45-50
• /
• 2002

This study was performed to develop thin layer drying equations fur short grain rough rice using far-infrared ray. Thin layer drying tests was conducted at four far-infrared ray temperature levels of 30, 40, 50, 60$^{\circ}C$ and two initial moisture content levels of 20.7, 26.2%(w.b.). The measured moisture ratios were fitted to Lewis and Page drying models by stepwise multiple regression analysis. Half response time of drying was affected by both drying temperature and initial moisture content at drying temperature of below 40$^{\circ}C$, but at above 40$^{\circ}C$ was mainly affected by drying temperature. Experimental constant(k) in Lewis model was a function of drying temperature, but K and N in Page model were function of drying temperature and initial moisture content. Moisture ratios predicted by two drying models agreed well with experimental values. But in the actual range of drying temperature above 30$^{\circ}C$ Page model was more suitable for predicting of drying rates.

• Journal of Biosystems Engineering
• /
• v.32 no.4
• /
• pp.237-246
• /
• 2007

In this study, the microwave free-space transmission technique was used to measure the dielectric property of powdered food at microwave frequencies. The sample holder was designed and fabricated to transmit the microwave signals ranging from 1 to 15GHz. From the microwave propagation theory the equation expressing the dielectric property of powdered food was derived and validated by standard dielectrics. The dielectric property of powdered food such as wheat flour, coffee powder and milk powder was measured and analyzed. In the uniform range of bulk density of material, the real parts of permittivity of the food samples increased with the increase of moisture content, bulk density and temperature of the samples. The propagation properties such as attenuation and phase shift increased linearly as the moisture density of the food samples increased. As a measuring frequency of the moisture content, the X-band was recommended.

• Macromolecular Research
• /
• v.17 no.11
• /
• pp.907-911
• /
• 2009

To improve the moisture stability of the $CaS:Eu^{2+}$ red phosphor, surface coatings with silica nanoparticles were performed using five different methods, i.e., $P_1$, $P_2$, $P_3$, $P_4$, and $P_5$. The phosphors were coated with silica nanoparticles using a dip coating method ($P_1$) and sol-gel method ($P_2$). The phosphors were coated using a solution containing silica nanoparticles and poly(1-vinyl-2-pyrrolidone), PVP, $(P_3$). The phosphors were also coated with silica nanoparticles by reacting with the 1-vinyl-2-pyrrolidone (VP) monomer ($P_4$) or by reacting with mixtures containing VP and tetraethylorthosilicate ($P_5$). A decrease in the photoluminescence (PL) intensity was observed regardless of the coating methods. However, the moisture stability of the phosphors was enhanced by the coating when aged in a temperature-controlled humidity chamber. Among these methods, the $P_4$ (or $P_5$) method exhibited the greatest increase in moisture stability of the phosphors. The coated phosphors showed a relatively constant intensity with aging time, whereas the uncoated phosphor showed a decrease.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.229-229
• /
• 2007

In this study, HEMA-based hydrophilic copolymers were synthesized and dielectric constant (K) of the polymer thin films were investigated by change hydroxyl group (-OH) ratio in the polymer chain. The different hydroxyl group ratios were characterized by FT-IR and its thin films were obtained by spin coating. As a result, due to the moisture absorption of the hydrophilic thin film, the dielectric constant has been increased as was expected. The highest dielectric constant (K=4.19, @1MHz) was observed at 40% hydroxyl group ratio among the several polymers.

• Journal of Power System Engineering
• /
• v.15 no.3
• /
• pp.46-51
• /
• 2011

Low temperature vacuum drying technique, whose drying time and quantity of exhausting energy is about 25~30% of hot air drying, is very excellent in the drying efficiency. This paper is made out in the aspects of heat engineering with the object of developing Korean drying machine which can dry once a large quantity of objects to be dried in the state of low temperature and vacuum. As the results, it took about 17 hours(3~4 days in case of hot air drying) for material to reach about 18% of the final moisture content in order to store products for a long time, from about 78~80% of the early moisture content at the beginning of drying, and maximum drying rate comes to about 0.35 kg/m2hr at about 400% of the moisture content.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.233-235
• /
• 1997

A free sparse transmission method using X-band standard gain horn antenna is applied to measure the attenuation and phase shift of microwave signal through the wetted grain such as rough rice, brown rice and barley. The moisture content of grain varied from 11 to 25% based on its wetted condition. The dielectric constant and loss factor, which depend on the moisture content of the wetted grain are obtained from the measured attenuation and phase shift by vector network analyzer. The measured values of dielectric constants as a function of moisture density are compared with values of those obtained using the predicted model for estimating dielectric constants of grain.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.20 no.4
• /
• pp.4799-4804
• /
• 1978

In order to investigate the effect of delayed compaction on the strength of the lime soil mixtures, labroatory test with two kind of soils was performed at four levels of lime content, at five levels of water content, and at six love's of delayed times. The results are summarized as follows; 1. Maximum dry density and optimum moisture content decreased with increase of the delayed times. The decreasing rate of those values at the earlier delayed time were large, and those values showed almost constant after about four hours of delayed time. 2. According to the increase of the delayed time, the decreasing rate of maximum dry density and optimum moisture content was large ia S-2 sampl, but was a little in S-1 sample. 3. Unconfined compressive strength of lime soil mixtures decreased with the increase of the delayed time, and the decreasing rate of its strength increased with the increase of the lime content. 4. Water content corresponding to the maximum strength was a little higher than the optimum moisture content along the increase of lime content and delayed time but its value was large in fine soil.

• Journal of the Korea Society of Computer and Information
• /
• v.23 no.11
• /
• pp.123-128
• /
• 2018

When the injection molding system molds some plastic products, defective product rate will be increased if plastic materials have some excessive moisture content. Therefore, it is very important to control the dehumidification and drying of plastic material. Since the moisture content of the plastic material may change from time to time depending on the material and the molding process, it is necessary to observe the change in real time and maintain a constant moisture content. To solve these problems, I proposed a smart factory system model for plastic molding in this paper. In addition, I designed the interface module to be installed in the dehumidifying dryer which is the core of this process. In addition to this, performance tests were conducted to check the effectiveness and the results were verified as valid.

• Journal of the Korean Vacuum Society
• /
• v.7 no.3
• /
• pp.167-272
• /
• 1998

The fluorine doped silicon oxide (SiOF) intermetal dielectric (IMD) films havc been of interest due to their lower dielectric constant and compatibility with existing process tools. However, instability issues related to hond and increasing dielectric constant due to water absorption when the SiOF film was exposured to atmospheric ambient. Therefore, the purpose nf this research is to study the effect of post oxygen plasma treatment on the resistance of nioisture absorption and reliability of SiOF film. Improvement of moisture ahsorption resistance of SiOF film is due to the forming of thin $SiO_2$ layer at the SiOF film surface. It is thought that the main effect of the improvement of moisture absorption resistance was densification of the top layer and reduction in the numher of Si-F honds that tend to associate with OH honds. However, the dielectric constant was inucased when plasma treatment time is above 5 min. In this study, therefore, it is thought that the proper plasma treatment time is 3 min when plasma treatment condition is 700 W of microwave power, 3 mTorr of process pressure and $300^{\circ}C$ of substrate temperature.